20 techmav 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Rear Corner Braces for Wilson II by TechMav
...erse
recreated the z-axis corner braces to add a cable pass-through hole to avoid running the cable up and over the lower rails.
thingiverse
free
Dell Z750P Power Supply Release Clip by TechMav
...this is a replacement cover for the rubber lock release that comes on the dell z750p power supplies (found in dell 2950 servers).
thingiverse
free
110mm Calibration Test with X/Y Orientation by TechMav
...e
i added an x and y marker to the part to make it easier to track the orientation after the part is removed from the print bed.
thingiverse
free
Smart LCD Controller Case by TechMav
... bracket in this remix.
openscad files are included. printed and tested to verify fit. lcd mount bracket was updated on 12/30/15.
thingiverse
free
BBB and Replicape Case with 80mm top fan by TechMav
...0mm fan to the top of the case, instead of the 30mm on the end, as i needed access to the ethernet jack the 30mm fan would block.
thingiverse
free
Minimal Replicape/Beaglebone Cooling Solution for 80mm fan by TechMav
...ion for 80mm fan by techmav
thingiverse
just resized this to allow for mounting an 80mm fan, as i didn't have a 50mm on hand
thingiverse
free
Modular Universal Phone Loading Dock Remix by TechMav
...er power block section for the original. it allows you to run docks on both sides, and to run a larger power brick in the middle.
thingiverse
free
Printrbot Simple 1405 Front Foot by TechMav
... it walk all over as it prints.
i also included a cut-down version that will print in the 100x100 area of the standard printer.
thingiverse
free
Wilson II Bowden Mount by TechMav
...ount for the motor to feed the hot end. i just used a regular bowden extruder and mounted it to the frame for the filament spool.
thingiverse
free
LM2596 Step-Down Regulator Mounting Board by TechMav
...mount the board with m3 x 3 screws. the corner holes are 2.5mm for threading, but you may want to adjust the hole size as needed.
thingiverse
free
Arduino Mega2560 and LM2596 Regulator Board Mount by TechMav
...ile is included. i tried to make it as parameterized as possible, but towards the end (the cutout section) i just wanted it done.
thingiverse
free
Printrbot Simple 1405 18"x6" Print Bed by TechMav
...uminum, to hold a steel plate that will give you roughly a 15 1/2" x 6" print surface, if you upgrade your y-axis also.
thingiverse
free
NEMA 17 Fan Cooler with zip tie slots by TechMav
...
i've also included two more that have the corner nipped out, to allow for clearance for the wire connector if you need that.
thingiverse
free
Wilson II Print Bed for Prusa i3 plate by TechMav
...h. the bridge is a very tight fit, to keep it from shifting.
fyi, the fan you can see in the picture is to cool the y-axis motor.
thingiverse
free
D-Bot bed leveling with big knob, 2020 version by TechMav
...side down so the adjustment wheel is underneath the extrusion.
recreated the part in openscad, in case anyone needs to modify it.
thingiverse
free
Y-Axis Drag Chain Mounts for Wilson II by TechMav
...unts to the lower frame using one of the screws from the z-axis brace. you will need to replace the 10mm screw with a 20mm screw.
thingiverse
free
Hypercube Evolution BLTouch Parametric Mount by TechMav
... file is just a sample. it is not meant to be downloaded and printed. use the openscad file and generate your custom length part.
thingiverse
free
2.5" to 3.5" SSD to Hot Swap Tray Adapter by TechMav
...pdate: slight mods, shortened the overall length to fit into the sled better, changed the screw holes slightly to line up better.
thingiverse
free
Wilson II X-Carriage Ends by TechMav
... the hole, but it will fit if your printer is properly calibrated. as such, i'm taking these off the work in progress status.
thingiverse
free
Beaglebone Black & Replicape Case by OCD3D
...black and replicape case... 30mm fan ** i added techmav#39;s version of the case utilizing a 80mm cooling fan...