43 ntdesign 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Parametric Base for Boardgames by ntdesign
...ametric to some extend (see provided stl files for examples). the bases in the foto are 17mm dia, 1mm slit, 5mm height, 80 faces.
thingiverse
free
remixed T-slot nut for 8020 by ntdesign
...tdesign
thingiverse
remixed t-slot nut for 8020 with 8mm slot width. slides in nicely, tight clamping with a single m4x12 screw.
thingiverse
free
Corner drilling jig by ntdesign
...arks [mm]: dist
number of marks: mark
upper & lower radius of holes: rup / rlo
make sure to use a well-calibrated printer :-)
thingiverse
free
improvised light stage by ntdesign
...arizing foil to the inside and use this in my lecture with a cheap usb microscope, to demonstrate polarizing effects in crystals.
thingiverse
free
Bead Chain connector by ntdesign
...is just pressed in, tolerance can be adjusted.
the provided model is set to 4.5mm diameter, 1.5mm wall strength, 0.2mm tolerance.
thingiverse
free
Mixing cup for concrete / cement by ntdesign
...d out to be not the best idea, my quick-dry cement basically degraded the material within 1 minute (huge mess - not recommended).
thingiverse
free
Jabra Evolve 20/30 Headset holder by ntdesign
...t & remote. the remote slides in smoothly & stays removable. the holder is designed to be affixed with double-sided tape.
thingiverse
free
Microscopy Slide Carrier by ntdesign
... here, or use the original thing and configure the container with these parameters:
diameter=32.0;
height=78.0;
inside_chamfer=0;
thingiverse
free
Skeleton Case upright by ntdesign
... a viewport). enough space to fit everything, i didn't bother redesigning for usb access and just drilled a hole in the side.
thingiverse
free
Micromount Sample Carrier by ntdesign
...mm/sec, 20% infill.
make sure to rotate the lid for printing, so the top is facing down (sorry for that, i lost the design file).
thingiverse
free
Rechargeable Battery Organizer by ntdesign
...back, tolerance of the battery sockets). battery symbols colored in with a felt-tip pen.
edit: added a version for 2x6 batteries.
thingiverse
free
Ergonomic Grip for Needle Collet by ntdesign
... is set to 5.5 mm, which works well for me with pla. it takes a bit of force to push in the metal grip, but still allows removal.
thingiverse
free
Cable Clip for IKEA Kallax by ntdesign
...eter in the scad file. it would actually work with a bundle of cables, but then you need more thickness and probably longer arms.
thingiverse
free
Generic Webcam 2020 extrusion mount by ntdesign
...5 sized hole, i designed this little part.
use the original bolt & screw, friction fit feels comparable to the original part.
thingiverse
free
Customizable Shop Vac Hose Adapter by ntdesign
...eceiving end to ensure a tight fit.
the provided stl fits a 32mm hose to this dust shoe: https://www.thingiverse.com/make:355128.
thingiverse
free
Parametric Box by ntdesign
... split at least 2mm bottom thickness is advisable. i plan to just glue the pieces together with a piece of tape on the underside.
thingiverse
free
Garage Remote Replacement Case by ntdesign
...only cosmetic and can be omitted.
do not print from pla, it will warp if you leave the car in the sun. pet-g works for me so far.
thingiverse
free
"El Cheapo" Magnet Base by ntdesign
...s. note: the print needs to be paused to insert the magnets. so far they fit and work well, time will tell how long they hold up.
thingiverse
free
Blast Shield Bracket by ntdesign
...m, 5mm sheet thickness, m6 screwholes.
the piece in the foto was printed with pla, 0.2mm layers, 80mm/sec. no supports necessary.
thingiverse
free
HPLC and snap-lid vial holders by ntdesign
...t fits various sizes of standard issue vials, the 20-slot variant is designed specifically for 1.1 (tapered) and 2 ml hplc vials.
thingiverse
free
Parametric Wood Strip Connector & Endcap by ntdesign
...ded stl files are only for show since my needs were rather exotic (15x30mm to 28x18mm and 3mm wall). holds up pretty well so far.
thingiverse
free
Glass Stopper Opener by ntdesign
...u run into problems, scale up the print slightly or adjust the parameters id14 / id29 in the scad file.
ns24 tolerances untested!
thingiverse
free
parametric HPLC vial rack by ntdesign
...periments. they are bit offset, so that they're always in the same place when plates with different tilt angles are combined.
thingiverse
free
Laundry Rack Riser by ntdesign
... mine from fillamentum flexfill 98a. the pins are only needed for centering, probably some cardboard slips will do just as well.
thingiverse
free
Biqu B1 Dial Gauge Holder by ntdesign
...int bed levelling positions still work. original fan screws can be used. don't forget to remove the gauge before printing ;-)
thingiverse
free
Perishable Food Day Marker by ntdesign
...ashup version with included bag clip: https://www.thingiverse.com/thing:4895918
based on https://www.thingiverse.com/thing:330151
thingiverse
free
2020 extrusion to UNC tripod adapter by ntdesign
...lows threading the usb cable through if necessary. wouldn't mount an slr on it, but for a lighter camera it is stable enough.
thingiverse
free
Ergonomic Grip for Needle Collet v2 by ntdesign
...t still allows removal.
minor changes from the original design: now all hollow, slightly improved printability and cooler endcap.
thingiverse
free
Custom travel toolkit by ntdesign
...le to fit it in). good printer accuracy is necessary, if they bake together just split the print and print everything separately.
thingiverse
free
Customizable Cyclone Separator (RMX) by ntdesign
...of testing with aluminum, it works fine so far. the bottle i'm using compresses a bit from the vacuum but still does the job.
thingiverse
free
Biqu B1 3D Touch Mount (for older clones) by ntdesign
...fset is -0.65 on my printer.
just tested this with an original bltouch 3.1, and it seems to work fine with roughly -1.5mm offset.
thingiverse
free
USM Haller cable mounts by ntdesign
...y poorly with overhangs). shown test pieces were printed in pla, but black petg is probably best (especially for printed screws).
thingiverse
free
BIQU B1 Smart Filament Sensor Bracket (parametric height) by ntdesign
...ile has parameters for the m3 diameter and a height offset relative to the pjraw version. with my extruder 3mm lower was spot-on.
thingiverse
free
X-Carve Loc-Line Holder by ntdesign
...s nice and flush. the design leaves the on/off switch accessible if you are using the dewalt router. you also need 3 m4x8 screws.
thingiverse
free
Heater Box for PTC element by ntdesign
...to attach the relief to the box with an m3 screw.
i designed two vial holders for this: https://www.thingiverse.com/thing:2891050
thingiverse
free
Microscope Slide Cooler by ntdesign
...blished. temperature control is possible but very limited (maybe +/- 15° but the base temp is predetermined by the actual setup).
thingiverse
free
Swisscom Internet Box 3 mounting bracket by ntdesign
...to file off a bit from the bracket to get access to the copper internet cable, but since i'm using fibre i didn't bother.
thingiverse
free
USB Microscope filter holder by ntdesign
...t want to get going, "filter_assembly_withclips.stl" very probably includes everything you need except the filter foil.
thingiverse
free
E3D v6 and Titan extruder Cyclone layer fan (new model Titan) by ntdesign
...ng toward x tubes and up): https://www.thingiverse.com/thing:2299900
i'll post a picture as soon as my x gantry is completed.
thingiverse
free
Drytube for Silicate Pellets with Anti-Backflow by ntdesign
...as shown, or nothing). the provided stl works with a 60mm diameter acrylic tube and a connecting hose with 12.5mm inner diameter.
thingiverse
free
Parametric Bag Clip with Perishable Food Date Marker by ntdesign
...t; by masterfx (https://www.thingiverse.com/thing:330151) with changes by bikecyclist (https://www.thingiverse.com/thing:3388572)
thingiverse
free
1980's Bow Lamp Repair by ntdesign
...covered with printed plug. this should hold forever. my press-in brass thread is 8.3mm long, 6.55mm od (press in from back side).
thingiverse
free
MP Select Mini Glass Bedclips by ntdesign
...om/thing:1835673
edit: removed a bug in the .scad file pointed out by pete. please use the fixed file if you want to play around.