18 nenadr 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
OneUp/TwoUp wire bundle guide by nenadr
...naps onto the bottom part..the upright is offset to the right, so it clears the top of the x gantry for x=0.
model in freecad.
thingiverse
free
TwoUp V2 nut holder by nenadr
...the original holder's too flimsy, and the hex nut hole is too large. i've made it beefier, with a better nut holder hole.
thingiverse
free
Simple harness for Nexus 5 by nenadr
...s and do a fairly minimal editing.
i place no restrictions on the use of this code - you are welcome to do what you like with it.
thingiverse
free
GoPro clip mount by nenadr
...d_primitives) and as a thing
(http://www.thingiverse.com/thing:1679551).
please feel free to use, share as modify as you see fit.
thingiverse
free
Plumbcheck gizmo to verify X-Y-Z axes are orthogonal by nenadr
... all the angles were 90 degrees.
the end of the x axis of the gizmo is cut off to mark it, so i would know which axis is which.
thingiverse
free
OneUp - TwoUp Z axis range extender by nenadr
... wires between the gantry and the handle. if you route the wires above the handle, you only need a 15mm shim.
model in freecad.
thingiverse
free
Box for Canon SX700HS Camera by nenadr
...y with certain cavities i placed in around battery holder to reduce the weight.
please fell free to use or modify as you see fit.
thingiverse
free
Filament spool bearing by nenadr
...
obviously, you will need two of each piece to mount a spool.
model in freecad. you're welcome to use and modify as you like.
thingiverse
free
openSCAD Primitives Library by nenadr
...n a 2x2x2 array in a hopefully intuitive fashion.
i maintain this code on github: https://github.com/imageguy/openscad_primitives
thingiverse
free
Small quick release clamp by nenadr
... make each jaw.
i put no restrictions on this design and related code. you are welcome to use, share or modify it as you see fit.
thingiverse
free
Thumbwheel-controlled twin potentiometer assembly by nenadr
...utral and green connects the pots.
i put no restrictions on this thing - you are welcome to use, share, modify etc. as you like.
thingiverse
free
Garmin Montana Kayak daybag mount by nenadr
... the montana is attached to the clip itself. the stl also has just the mount part of the clip, print clip.stl for the other part.
thingiverse
free
OneUp - TwoUp QU_BD kit heated bed retainer clips by nenadr
...
i have a sheet of pei on my bed, but the thickness should not make much of a difference.
model in freecad, feel free to remix.
thingiverse
free
Adapter to mount a filament spool on a thinner axle by nenadr
...ter in use on a 1/2" dowel axle.
i make no restrictions on this code, feel free to use, modify, share, etc., as you see fit.
thingiverse
free
Perimeter Bear Alarm Fence by nenadr
...arate pieces. but it still took weeks before i got to the point i was really efficient with setting up and taking down the fence.
thingiverse
free
3d Printer End Stop Made from Scratch by nenadr
...ve-resistor/ for the gory details.
i make no restrictions on use of this code, feel free to use, modify, share, etc. as you like.
thingiverse
free
E3D V6 hotend retainer clip for QuBD One/Two/ThreeUp Printers by nenadr
... and don't obstruct the clip.
i place no restrictions whatsoever on this design - feel free to use and modify as you see fit.
thingiverse
free
Wire Guide front faced by dmaccallum
...use them instead. hope this helps someone. thanks to nenadr for the first design that let me remake it...