20 mysophobe 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Rope thimble by Mysophobe
...e.
hole diameter is 10mm, so scaling is easy .. 80% for 8mm rope, 120% for 12mm etc
includes a simple spacer with same dimensions
thingiverse
free
USB simple stackable hanger by Mysophobe
...ger by mysophobe
thingiverse
print, connect, hang, store.
simples!
no it doesn't stress the plug! (someones going to say it)
thingiverse
free
Mysophobic Finger Keyfob by Mike-vom-Mars
...printing:
no supports needed
layer height 0.1mm - 0.3mm
use a raft for good adhesion
print size can be adjusted to fit your needs
thingiverse
free
Sanding pad Micro mesh organiser by Mysophobe
...e holder for your micro mesh pads with a slot in the rear for the grit reminder sheet.
can be printed without supports or infill.
thingiverse
free
Mask respirator - The Platypus by Mysophobe
....4 due to very thin parts.
for best fit, print a test fit section only .. squish your pouty mush into it; then scale accordingly.
thingiverse
free
Thermocouple wire storage by Mysophobe
...into the plug slot, use the clip (not tested) or the tried and true method of elastic bands.
designed around an 8.5mm x 16mm plug
thingiverse
free
Wiregate carabiner by Mysophobe
... complex and then messed up, but a model was created so i'm sharing it until i remake it with better "editability".
thingiverse
free
Rugged storage box by Mysophobe
...strength.
80+% fill recommended, most importantly the clip needs full fill.
stl box dimensions (mm) 25h x 30w x 95l (30/70 split)
thingiverse
free
Raspberry Pi camera case by Mysophobe
...not the wide angle version but may work if the lens extends out of the case.
uses 3 & 4mm bolts.
for camera board 25mm x 25mm
thingiverse
free
Rugged box large by Mysophobe
....(only because i have 4mm rod)
box 120mm x 70 x 50 internal
hinges might not have clearance
some post processing may be required.
thingiverse
free
LED Arch bridge - half circle by Mysophobe
...her with m3 nuts or tie wraps.
not tested/built/printed. just a concept at this time. there's far easier ways to build these.
thingiverse
free
LED spiral cone by Mysophobe
... strips won't handle the compound curve.
plenty of room inside to stuff any electronics.
hang from the ceiling for fun times!
thingiverse
free
RaspberryPi Zero W case by Mysophobe
... a sightly thicker top and taller where the ports are as the printed lid touched the hdmi port.
dimensions (mm) 6.5 x 71.2 x 36.2
thingiverse
free
Sine wave pill box by Mysophobe
...ions, so would love feedback on how better to generate this sine wave.
editable file also available here: https://a360.co/336gggt
thingiverse
free
Temp tower for labelling by Mysophobe
...an be used with 0.1 and 0.2 nozzles also.
...06noz_03layer.stl = 0.6 nozzle & 0.3 layer. can be use with 0.1 and 0.3 nozzles.
thingiverse
free
Bow - Cam rework by Mysophobe
...ildplate supports.
0.4nozzle, 0.1 layer, 100% fill, petg
i also have some accessories - https://www.thingiverse.com/thing:4840065
thingiverse
free
Tiny part organiser by Mysophobe
...tion. i'll model that soon. (no promises).
holds approx. 1 trillion molecules when not in use.. unless you live in a vacuum.
thingiverse
free
Compound bow accessories by Mysophobe
...es buildplate support needs and improves line channels. got an excellent print from petg, 0.4 nozzle, 0.1 layer height, 100% fill
thingiverse
free
Rotary Tool Drill Bit Sharpener by Mysophobe
..." can have a 4mm rod inserted (any material) as a brace for even less flex. the drill bit itself is usually the wobbly part.
thingiverse
free
Tap Flap - Clean as you go! by Simonwlchan
...imilar taps, so i'm mainly sharing this as a design idea. if you have a similar tap and it works for you too, let me know! :)