19 melihka 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
FPV250 Frame Top Plate by MelihKa
...fpv250 frame top plate by melihka
thingiverse
top plate for hobbyking fpv250 frames.
thingiverse
free
8mm Propeller Nut Wrench by MelihKa
...8mm propeller nut wrench by melihka
thingiverse
easy to use this wrench for prop tightening. it's really useful.
thingiverse
free
Decathlon Swimming Mask 22mm HME Filter Adapter by MelihKa
...decathlon swimming mask 22mm hme filter adapter by melihka
thingiverse
unfinished project
thingiverse
free
Easy Print Slug Trap by MelihKa
...single part slug trap.
no support or raft required.
half circle design is ideal for garden edges and green houses.
just add beer!
thingiverse
free
114mm Square Gutter End by MelihKa
...'m using these gutters to grow strawberries.
i've printed the end from abs and used pvc adhesive to glue it to the place.
thingiverse
free
Eachine camera to HK FPV250 adapter. (10 degrees tilted) by MelihKa
...hk fpv250 adapter. (10 degrees tilted) by melihka
thingiverse
you need 4 pcs m2 screw for camera and 2 pcs m3 for frame montage.
thingiverse
free
Mini Solar Charger Adjustable Foot by MelihKa
...y.com/itm/230993092332
you can use it for solar panels and photo frames.
you need only one set 20mm m3 bolt and nut to hinge.
thingiverse
free
FreeTrack / TrackIR Infrared LED Clip by MelihKa
... resistor
1x on/off switch
1x cr2032 battery holder
1x cr2032 battery
~30cm wire.
epoxy resin or hot glue to fix the components.
thingiverse
free
Underwater Glider Design by MelihKa
...ody tube. (between body and tail)
you can use lead, small stones or sand as balance.
i will take a glide video in a few days.
thingiverse
free
3D Printed Hand Corker for Wine Bottles by MelihKa
...e hole and press with the insert. that's all.
you can use pure acetone to improving the surface quality of the inner surface.
thingiverse
free
TrackIR Headset for FreeTrack Software by MelihKa
...ge.
polymorph plastic melt in hot water and molded by hand over leds as diffuser.
it's working perfect with hacked ir webcam.
thingiverse
free
MicroQuad for 7mm Hubsan motors and propellers by MelihKa
...or abs
you can find h107l motors and props on ebay. (total ~£10)
i'm using with hk x-dart controller but waiting for scisky
thingiverse
free
Cola Bottle Bidet - Toilet Roll Saver by MelihKa
...e output for the hard stuff :)
however, no support needed.
3 layer wall thickness
0.2 mm layer
pla+
please share your makes here.
thingiverse
free
Time Lapse Pan Motor (Kitchen Timer) by MelihKa
...er), you need 1-2mm paper as spacer. or use sponge or something like that.
it is working like a clock, because it is a clock :)
thingiverse
free
DJI Spark Remote to GoPro Adapter (compatible with Mavic) by MelihKa
...egrees as the photo for continuous flexible surfaces.
dji spark remote carbon fiber skin: http://www.ebay.co.uk/itm/122653077308
thingiverse
free
Tiny Trak Chassis for N20 Motors v4.0 by MelihKa
... motor controller board with frsky receiver.
the magnetic top replaced with screw holes. you can use m2 screws for the top cover.
thingiverse
free
Tiny Trak Chassis for N20 Motors v5.0 by MelihKa
...y own tinydrive v1.0 sbus motor controller board with frsky receiver.
i didn't design a top cover yet, you can make your own.
thingiverse
free
Tiny Trak Chassis for N20 Motors v1.0 by MelihKa
...or driver and control the tank over the free rcwcontroller app. you can also use rc receiver and brushed esc to drive the motors.
thingiverse
free
Tiny Trak Chassis for N20 Motors v2.0 by MelihKa
...are and default abd profile to print 0.3mm layer thickness for a fast test prototype. this is why my end results are really poor.