19 maot1985 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Knobs by maot1985
...printing you can press din934 nuts into the knobs. for the star knobs there are small round plates, which can also be pressed in.
thingiverse
free
Vinyl Cutter by maot1985
...e a selfmade wooden cnc. for the roland-vinyl-cutter i needed a holder. the holder i designed is spring-loaded with rubber bands.
thingiverse
free
Vacuum pads by maot1985
...me simple designs of vacuum pads.
for my little cnc i wanted to have some vacuum holders. they are quite small and easy to print.
thingiverse
free
Mixer 30mm by maot1985
...n has a mouth of 35mm. i made her a 30mm mixer. using a m8 cutter, an m8 threaded rod and a nut, the mixer was quickly assembled.
thingiverse
free
moMPCNC by maot1985
... used in prusa printers. the belt tension will be placed on the carriages and the stepper motors on the top of the corner posts.
thingiverse
free
Hammock Rain Protection by maot1985
...ickness.
glue the pieces over the ring with some hot glue so that no water can flow between the printed parts and the steel ring.
thingiverse
free
PL55 stopper by maot1985
...er/scheppach-zubehoer-set-/p/20749949).
use a m6 nut, a din912 m6 bolt and a m6 lever (e.g. from misumi) and you are ready to go.
thingiverse
free
Clamp M8 by maot1985
...he clamp in black pla from bq. layer height 0,3mm, 50% infill. the base is printed with supports generated by autodesk meshmixer.
thingiverse
free
moDRO by maot1985
...
the lcd-address can be found with this little sketch from https://playground.arduino.cc/main/i2cscanner
i hope i made no mistake
thingiverse
free
Kindle Fire ridgeline mount by maot1985
...et in from the side and hang the mount on the ridgeline.
you need two threaded rods m5x140,10 nuts m5 and two bolts din912 m5x25.
thingiverse
free
Clamp M5 by maot1985
...he clamp in black pla from bq. layer height 0,3mm, 30% infill. the base is printed with supports generated by autodesk meshmixer.
thingiverse
free
Galaxy Nexus wall-mount by maot1985
... attached to a acrylic window and i wanted to have a secure mounting. so i changed the existing mounting to 4 holes for m3 bolts.
thingiverse
free
mophesto 2.0 by maot1985
... plates of the x-axis are planed as acrylic plates.
the system looks a little bit heavy, but i'm not printing at high speeds.
thingiverse
free
Qi-Car-Dock by maot1985
...-joint from brodit.
update:
since last week i have the lg g4 with its official circle flip case. therefore i also made a dock ;-)
thingiverse
free
Cyclone by maot1985
...trands in the vacuum cleaner, only a little little bit of dust. to clean the cyclone i only have to remove the bottom dn110 pipe.
thingiverse
free
mophesto by maot1985
...d=0
the voltage divider and the capacitive sensor for the z-axis are from http://www.3d-proto.de/index.php?p=tips_autobed#autobed
thingiverse
free
BQ Hotend DIY by maot1985
...lex kk396 connectors. i attached a kk396 header to the original heater cartridge cable in order to use the original hotend again.
thingiverse
free
DN110 Cyclone Adapter by MrConcept
...bucket lid adapter for the cyclone dust collector by maot1985 ...
thingiverse
free
Geeetech A10 Semi-Circular Fan Duct by dsaiz
...impresora geeetech a10 basado en el diseño https://www.thingiverse.com/thing:3537682 de maot1985 duct for layer fan in semi-circular format for geeetech...