21 killacycle 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Paintball Cylinder Cap by KillaCycle
...takes about half an hour to print using pla. it is always a bit of a challenge to make threads that work correctly. these do. :-)
thingiverse
free
Taz5 Bracket for DiiiCooler Duct by KillaCycle
... peer between the fan duct and the table.
(see my low profile heated bed tabs that you will also need if you install this duct.)
thingiverse
free
Low Profile Heated Bed Tabs by KillaCycle
...aching it. rest the duct on three of these tabs and tighten the screws. your diicooler duct will be level and the correct height.
thingiverse
free
Dishwasher Basket for Silverware and CHOPSTICKS! by KillaCycle
...file. the grate extrusions are "delicate". if you attempt resize the bars, etc. they tend to fail. (ask me how i know.)
thingiverse
free
Heated 3D Printer Enclosure by KillaCycle
...it in the last picture. you can use a very compact 120vac space heater with a built-in thermostat instead if you are on a budget.
thingiverse
free
LH Mount for Turbo Fan Duct, Taz5 by KillaCycle
...u might wish to replace the 24volt 30w heater in your extruder with a 24volt 40w heater. you can then run the fan all the way up.
thingiverse
free
M-33 V-belt for Mitsubishi DB-130G Sewing Machine by KillaCycle
...o fit it, however, but it is near the minimum range for the adjustment.
inventor 2018 file included so you can change the length.
thingiverse
free
Overhead Filament Spool Holder (Lulzbot Taz) by KillaCycle
... nuts wedged in the center slot in the printer rail. seems to work fine for us just resting on the rails without screws, however.
thingiverse
free
Taz replacement 25mm hotend Fan Duct by KillaCycle
...ut abs would work as well. pla or hips would likely soften or melt in use, but you could try it if that is what you have on hand.
thingiverse
free
Digital Dial Indicator/Caliper Connector with Built-in Level Shifter by KillaCycle
...this connector on masterkookus' thingiverse post, and learn how to wire up the level shifter on wel-hsiung huang's blog.
thingiverse
free
Smaller (50mm) Motor Pulley for Mitsubishi Sewing Machine DB-130 by KillaCycle
...w.thingiverse.com/thing:3033488
best to print with petg (innova, nvent, etc.) you could print it with abs or nylon if you prefer.
thingiverse
free
RPM Hall Sensor for Motor Fan Mount, Speedometer, Arduino by KillaCycle
...magnet on the wheel somewhere, mount the ky003 sensor so that the magnet passes nearby, and "bob's your uncle". :-)
thingiverse
free
Overhead Filament Spool Holder (Lulzbot Taz) (For 16mm OD rod) by VooDooMoN
...rod) by voodoomon thingiverse this is a remix of killacycle#39;s initial part. i modifies the spool rod diameter to...
thingiverse
free
Filament Pelletizer Cutter, Pellet Maker, Filament Recycle by KillaCycle
...xact combination and concentration of pigment you want. you can remix the pellets so the color is more evenly blended if need be.
thingiverse
free
Lulzbot Mini 30mm Hot End Cooling Fan by littlelocos
...30mm fan from evercool (fan-ec3010m05ca). it was inspired by killacycle#39;s taz, however, it has been redesigned to work with...
thingiverse
free
Extended Overhead Filament Spool Holder (Lulzbot TAZ) by rogerpeng1
...holder (lulzbot taz) by rogerpeng1 thingiverse a remix of killacycle#39;s overhead spool holder to accommodate 3kg filament spools. new...
thingiverse
free
Overhead Filament Spool Holder (Lulzbot Taz) - With Retaining Pin by JMcAz7
...a lulzbot taz printer. this is a remix of killacycle#39;s spool holder, but i've modified it so that the...
thingiverse
free
Updated Overhead Filament Spool Holder (Lulzbot Taz 6 or Taz 5) by Dereksunday
...space. found this really good filament spool holder from killacycle that looked great - the style matches the printer...
thingiverse
free
DiiiCooler for Wanhao Duplicator i3 / Maker Select by Pawpawpaw85
...i3. [adapters for other printers] taz5 - http://www.thingiverse.com/thing:1306388 (by killacycle taz5 - http://www.thingiverse.com/thing:1462875 (by killacycle) folger tech 2020 i3...
thingiverse
free
Easter Egg, Two Color Gift Box by EvaHakansson
...egg. you can download them here from http://www.thingiverse.com/thing:1424791 user killacycle#39;s thingiverse page. cooling: 100 % cooling fan speed gives...
cults
free
Extended Overhead Filament Spool Holder (Lulzbot TAZ)
...taz) cults 3d_printer_accessories 3d_printer_parts filament_spool_holder spool_holder a remix of killacycle#39;s overhead spool holder to accommodate 3kg filament spools. new...