22 jakabo27 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Greek Delta Symbol Cookie Cutter by jakabo27
...greek delta symbol cookie cutter by jakabo27
thingiverse
simple delta cookie cutter that isn't wavy on the side.
thingiverse
free
Tea Dispenser Magnet Holes for Tea Packets by jakabo27
...ngiverse
a remix with the thumbhole and inset areas for magnets to go in the back. my magnets are 60mm x 10mm x 3mm from amazon
thingiverse
free
Light Switch Cover Lock by jakabo27
...ould still bump the switch and momentarily turn the outlet off. this is my solution - don't let you touch the switch at all.
thingiverse
free
No Brim Krups Espresso Splash Guard Lid by jakabo27
...gs in the slicer before printing it. i recommend printing with supports on everything, it will look nicer than without supports.
thingiverse
free
LED Strip holders for APA102 144/m LED strip by jakabo27
...trip - "apa102 daylight white dc5v 144leds/m programmable led strip lights- 1m/3.28ft per roll" on superlightingled.com
thingiverse
free
Pixel Pushing Jig for Boscoyo ChromaTrim V4 by jakabo27
...supports. i set the walls to have 4 perimeters and 25% infill. it's wicked strong, if you break it you did something wrong.
thingiverse
free
Rubber Gasket for Waterproof Ethernet Connector by jakabo27
...ctor + one end waterproof head ethernet lan cable connector double head coupler adapter female to female with waterproof/dust cap
thingiverse
free
Vertical Mount for 4 String Differential Smart Receiver Board by jakabo27
... to the part. you can install the power connector after mounting to the part but it will probably be easier if you do it before.
thingiverse
free
Smooth PPD Geo Wreath Mount Remix by jakabo27
...tps://boscoyostudio.com/
ppd: https://www.pixelprodisplays.com/
xlights facebook group: https://www.facebook.com/groups/xlights
thingiverse
free
Stronger Link-2 Arm for Polar Bear with Seal Automata by jakabo27
... pull on it too hard, or when you look at it funny.
print with supports for best results (for the pin end, not my reinforced end)
thingiverse
free
Flat Velcro Mount for Smart Receiver 4-String Differential Receiver by jakabo27
...product
use short m3 bolts to attach the smart receiver to the part. it has two support areas under the board for added strength
thingiverse
free
Bathroom Sink Vanity Top Organizer Holder by jakabo27
...//www.thingiverse.com/thing:370074
printed it separately for strength and so i can swap it out easily if it gets gross and dirty.
thingiverse
free
Panel Mount for BTF-LIGHTING generic Waterproof Electrical Connector by jakabo27
...in and the 4-pin, so i'm assuming it's the same for 3, 5, and 6 as well.
print laying flat on the bed, 2 per connector.
thingiverse
free
Shelf Corner Bumpers for Head Protection by jakabo27
... just resize the file in your slicer to the dimensions you want. mine is designed for a shelf that is 140mm deep by 16.5mm tall.
thingiverse
free
xConnect Panel Mount Flat by jakabo27
...rough the mount and into the hex nut (attach hex nut here if you haven't already). tighten it up nicely and you're done!
thingiverse
free
Corner Stake Replacement for Volleyball Court Ground Webbing by jakabo27
...int with supports everywhere, but change the overhang threshold to just 10° so that the rear side doesn't get supports added.
thingiverse
free
Dish Wand Refillable Soap Scrubber Holder for Kitchen Sink by jakabo27
..." feature on the small one. the larger one needs to be printed with supports under the arms as shown in one of the pictures
thingiverse
free
Snap-together Filament Spool Holder 608 bearings by jakabo27
...distance" parameter to change the separation between the sides.
original: https://www.thingiverse.com/thing:3335976/files
thingiverse
free
Meanwell LRS-350 Mounting Feet and Ventilation Shelf by jakabo27
...esigned to be printed with the chamfered hole facing vertical, like you would put a screw straight down it and have it fit flush.
thingiverse
free
5mm Adapter for 60mm Mecanum Wheels to Stepper Motors by jakabo27
...g to maximize your use of the given space like we are this year for our 7" by 7" by 7" robot for southeastcon 2021
thingiverse
free
XT-60 Female Flat Panel Enclosure Mount for Amass Connectors IMPROVED by jakabo27
...'t bother removing the supports because it's just 2 layers of it and screwing in the nut breaks free of it easily enough.
thingiverse
free
Yet Another Motorized Lazy Susan Spinning Platform by jakabo27
...he project and don't feel like improving it now, but yeah expect to need to attach it to a base board. i just used hot glue.