21 imgumby 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
no mask by imgumby
...no mask by imgumby
thingiverse
3d printed no mask logo.......use as you see fit..
thingiverse
free
TBS Source V arm bumper remix by imgumby
...tbs source v arm bumper remix by imgumby
thingiverse
remix of https://www.thingiverse.com/thing:4395732
thingiverse
free
Launch Pad for Dave_C_FPV Rocket Drone by imgumby
...thingiverse
for dave_c_fpv rocket drone..figured it needed a launch pad but no hope of landing on this so a net is in the works.
thingiverse
free
shark byte control board holder by imgumby
...ngiverse
made this just to protect it a little and the byte frost holder here doesn't fit the newer board....print in tpu...
thingiverse
free
Shark Byte Module Monitor Clip by imgumby
...8mm deep monitor as is...slot is 20mmx28mm and fingers are sized for stock module.
hope this helps
printed
20% infill
3 walls
pla
thingiverse
free
TBS SOURCE Aureo Arm Guards by imgumby
...on weighs 4.2 grams each @10% infill and the lightweight version sans motor protection weighs in at 2 grams..approximately..ypmv
thingiverse
free
TBS SOURCE Aureo Arm Guards by imgumby
...on weighs 4.2 grams each @10% infill and the lightweight version sans motor protection weighs in at 2 grams..approximately..ypmv
thingiverse
free
32mm solder flux anti tip bottle holder by imgumby
... in tpu . slides right in fine but may want to consider scaling up a percent or 2 in the slicer if printed in a harder plastic.
thingiverse
free
Armattan Rooster JHE20B Quad Finder cheek mount by imgumby
...lem.the other mounts i found were for belly mounting slightly smaller buzzers.clears a 5 inch prop but probably not a 5.1 inch...
thingiverse
free
TBS Source Aureo GoPro style finger mount by imgumby
...ndard gopro mount..
attach with 2mm screws plus a nut and washer under the canopy
printed in tpu @ 100% infill = about 5 grams...
thingiverse
free
Catalyst Machineworks 4" Shocker UL parts by imgumby
.../www.thingiverse.com/thing:4736559
little minimalist rear landing skid so you're not landing on the gps mount all the time...
thingiverse
free
Shark Byte VRX Tile angled by imgumby
...inted mine with sma connector face flat on the bed with tree supports
remixed from https://www.thingiverse.com/thing:4652189
thingiverse
free
Quadcopter Drone Max Cell Tags by imgumby
...else..1,2,3,4,6,and 12 cell tags..i guess i should have made up a 5 but don't use them myself ...yet.
3 lines 100% infill tpu
thingiverse
free
18650 21700 battery pack accesories by imgumby
... i printed in tpu .to be honest i made the caps and don't use them but included just in case someone might find them useful..
thingiverse
free
TBS Source Aureo Side Impact Guards by imgumby
...re than minor tumbles but better than nothing i think if you can stand the weight penalty..
printed with 3 walls at 100% infill..
thingiverse
free
ImmersionRC Ghost Antenna mounts by imgumby
...test printed only #1,2,and 5 as those were the ones i needed and they fit fine....the rest..?????...
measure twice..print once...
thingiverse
free
Hydrophobe fpv camera cover by imgumby
... tested yet..be the first !..lol
hopefully this is helpful to someone.
based on...https://www.thingiverse.com/thing:4227933/files
thingiverse
free
Cable strain relief for SMO 4K Camera by imgumby
...ate connector down stream closer to the flight controller so you don't rip the wires from the board for another safety valve.
thingiverse
free
Shark Byte TX5S.1 Vtx 30x30 Adapter remix by imgumby
...y bolts have to stop about 4mm in from bottom to avoid hitting underside of vtx... ...print in tpu so you can flex the vtx in...
thingiverse
free
insta360 one r fpv lens guard adapters by imgumby
...rd stitching option turned on..have not tested durability as of yet but they are firmly attached.
printed in tpu at 100% infill.
thingiverse
free
x-knight 360 gopro cable sd card storage box by imgumby
...n pla...3 walls...20 % infill ...the lid fits snug but probably won't stand being shaken upside down with anything inside.