19 giulianom 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Lumia 640 Mount by GiulianoM
...l shrink to the correct size. abs will also more likely resist high temperatures in a car, so i wouldn't recommend using pla.
thingiverse
free
Dust Collector Blower to 6" Duct by GiulianoM
...l fit in sdr pipes of slightly varying diameters.
used for venting the blower outside or otherwise into some other 6" input.
thingiverse
free
4" x 6" Oval Hole Template by GiulianoM
... 7", and the distance between the two walls is 6.04".
clamp it down over a 6" board and the oval will be centered.
thingiverse
free
MicroSwiss Ender 5 Plus Direct Drive Plate by GiulianoM
...ve-extruder-for-creality-ender-5
i am using the stl to design a cooling shroud since there are extra mounting holes on the plate.
thingiverse
free
Dial Indicator Mount for MGN12H Linear Block by GiulianoM
...m3 10mm screws for mounting the adapter block to the mgn12h carriage.
1 x m3 screw, 10-15mm long for securing the dial indicator.
thingiverse
free
Arducam 5MP OV5647 Camera Mount by GiulianoM
...e should come with the camera kit.
if not, you'll need 4 x m2 15mm screws and 4 x m2 nuts.
m2 - 2mm screws, not m2.5 - 2.5mm.
thingiverse
free
LM8LUU Bearing Blocks for Prusa Y-Axis by GiulianoM
...the blocks to the y-carriage. 20mm are long enough if your plate is threaded - use 25-30mm with nuts if yours is drilled through.
thingiverse
free
i3 Z-Ends for LM8LUU and 8mm Anti-Backlash Nut by GiulianoM
...44
these are the z-end parts that correspond with the x-ends i designed:http://www.thingiverse.com/thing:1060956
work in progress
thingiverse
free
Mini Height Differential IR Sensor Board Mount for E3D v6 / Prusa i3 Rework by GiulianoM
...t onto the bottom two m4 bolts for the "e3d v6 compact extruder for i3 rework":
http://www.thingiverse.com/thing:725082
thingiverse
free
Dual Melzi Box for RepRapPro Tricolor Mendel by GiulianoM
...clips on the top piece snapped off really easily, so i modified the top to make the clip walls a little thicker (2.0mm vs 1.5mm).
thingiverse
free
Prusa Rework X-Carriage for LM8LUU by GiulianoM
...ck, and insert one of the m3 screws through the loop to secure it.
repeat the same for the other side, and then tension the belt.
thingiverse
free
NEMA17 Sub-Micro Servo Bracket for Auto Bed Leveling by GiulianoM
...ni switch of that same shape.
the alignment of the pins puts the switch's roller end to be just under the servo's axis.
thingiverse
free
Ender5 MicroSwíss 4020Fan Part Cooler Ring by h3nkGer
...fits the upcoming remix of the fan shroud by giulianom ...
thingiverse
free
i3 X-Ends for LM8LUU and 8mm Anti-Backlash Nut by GiulianoM
... i had to revise the motor part to be a bit thicker. also made the belt pathway wider, to 10mm, so it can handle a 9mm-wide belt.
thingiverse
free
Ender 5 Plus Linear Rail Conversion by GiulianoM
... then adjust the pulleys on the y-axis to compensate, then print another yacs x/y calibration part.
repeat above until satisfied.
thingiverse
free
Lumia 640 mount by galbro
...usa mounting system. i started with the mount by giulianom edited it in the microsoft 3d builder to trim...
thingiverse
free
MicroSwiss Backplate for Ender 5 by MyFunctionalDesigns
...this is a remix of the stl posted by giulianom well, not really a remix, just a cleaned up...
thingiverse
free
Fan Shroud for MicroSwiss Direct Drive Extruder on Ender 5 Plus by GiulianoM
...e bridging angle to be 180 so that the bridge goes horizontally across the x axis.
otherwise the fan shroud printed great in pla.
thingiverse
free
Ender 5 Plus MicroSwiss Cooling Duct - Single Side Only by blammojp
...- single side only by blammojp thingiverse remix of giulianom#39;s cooling duct to remove the duct on the side...