16 fickert 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Shower drain by Fickert
...can be scaled as well to fit your shower / bath tub drain without issues. i checked sizes for scaling with common pipe diameters.
thingiverse
free
Hpperlow CG Power Wire Retainer by Fickert
...ingiverse
a quick print to keep the power wires retained on any 30 x 30mm screw pattern. specific to the hyperlow series frames.
thingiverse
free
Pixhawk 2.1 mounting Template by Fickert
...eated this model for you guys to print. it has the cube centered with the four inner holes, and has the drilling portions marked.
thingiverse
free
Folger Tech FT-5 Spool Mount for 25mm Carbon Fiber Tube by Fickert
...r tube by fickert
thingiverse
this is for a requested size upgrade for some spare carbon fiber tubes someone asked for.
cheers!
thingiverse
free
Panel Due 7in TFT mount Rev1 by Fickert
... or tomorrow for ease of use with anyone's printer. this is meant to be mounted in the corner of two extrusions (right side).
thingiverse
free
Ummagawd Remix TBS Unify / RDQ Mach 2 VTX Pigtail Mount by Fickert
...for vtxs that use the t style pigtail. works great and very sturdy. no supports needed. recommend abs or petg; a sturdy material.
thingiverse
free
Magpul M Lok Rail Cover Insert for Loose Rail Covers by Fickert
...to spec. these are designed to account for the additional room. these may not work for you without modification. best of luck! :)
thingiverse
free
Pixhawk Safety Switch Mount by Fickert
... flat: this is the same design to hide the screw threads, but with a flat bottom. easier to print for most and should do the job.
thingiverse
free
ScottyBoard Teesnys LED Drive PCB Case by Fickert
...e currently. if the smaller 10uf can fit without interference please let me know and i will remove the circular hole for the cap.
thingiverse
free
Glass Fasteners for print Bed (Designed for FT-5) by Fickert
...versions. use 100 percent infill to ensure strength.
you will also need 8x m3 nuts to use to mount like in the pictures provided.
thingiverse
free
Hyperlow CG VTX Pigtail Mount W/ Capacitor Mount (TBS Unify style pigtail) by Fickert
...ecommend simplify3d as automatic supports tend to make too many.
i included a photo of the best orientation you will print with.
thingiverse
free
DJI/Tarot 15 x 5.5 Folding Prop Balancer Adapter by Fickert
...ing an fdm. there are minor drafts and features that will likely not turn out well unless you do so. material is your preference.
thingiverse
free
Folger Tech FT-5 Spool Mount for 16mm Carbon Fiber Tube by Fickert
...amps are fine. this will use 4x m3 x16mm screws you have left over from your ft-5 kit and uses 6x m5 x 10mm screws and 6x t nuts.
thingiverse
free
Folger Tech FT-5 TFT32 Screen mount (Rev 3) by Fickert
...unt.
as before my printer is still down (i have about 2 pieces of hair left on my head) so please provide feedback to this model.
thingiverse
free
DJI Inspire 2 X5S Balance Ring Adapter for 45-175mm Panasonic Lens - LEAD WEIGHT REQUIRED by Fickert
...o adhere the lead weight.
refer to the photo with the yellow surface, this is where hot glue is applied to hold the lead weight.
thingiverse
free
FT-5 Enclosure Braces for 1/8in acrylic by Fickert
...) mounted if you have made it this far.
any questions please ask me on here or in the folgertech forum/ facebook group.
cheers!