20 exruder 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Dual 40mm Cooling Fan Ring for E3D V6 Exruder by roadie3rd
...g fan ring for e3d v6 exruder
requires:
2x 40mm fans,
1x 30mm fan,
10x m3 x 16 screws
4x m3 x 8mm
2x m3 nylock nuts
2x m3 washers
thingiverse
free
Bowden input exruder upgrade for CR-10 by wbarber69
...449006
that uses bowden tube from the spool all the way to the extruder, so i needed to make a bracket to mount the ptfe tube to.
thingiverse
free
A8 Exruder Fan Mod with hinge pin by rmorrow50
...lly hard time finding a screw for the hinge so i simply just made one, i ended up just needing 2xm3-30mm with nuts and 2xm3-20mm.
thingiverse
free
CR10 exruder fan
... support and use your good judgment. it can be hard to remove support from the small duct without destroying the flange in there.
thingiverse
free
M6 Nut Funnel Cover - Exruder Filament Guide by nBurn
...00 models that use a thinner m6 nut to hold the bowden tube in place. the wide version has a width 50% greater than the original.
thingiverse
free
Bowden Extruder - 625zz Bearing by rawkstar320
...- 625zz bearing by rawkstar320 thingiverse i redrew this exruder in order to be able to use a 625zz...
thingiverse
free
Ender 3 Pro Exruder Relocation Mount with Filament Guide / Runout Switch by WesCassar
...t.
i also put a mount on the unused space of the top section with the filament runout, for future light / camera / anything else.
thingiverse
free
SC8UU Minimal Bearing Carrier with AM8 Y endstop trigger wing by quualudes
... it looks fine, will deform the bearing and then you will be riding an oval bearing on a round rod - with the obvious issues. :p
thingiverse
free
FAN bracket by GeirJansen
...25-30mm lenght 4mm screw. i made this for the exruder stepper on my machine that really gets quite hot...
thingiverse
free
Prusa I4 Throat Fan Duct by munive
...the extruder and damage the teflon lining. remove the exruder fan assemble the heat sink with shorter screws move...
thingiverse
free
Extruder Exhaust Fan for Overlord Pro by chrisdug
...enclosure really works well. after several hours - the exruder motor is at room temp still. now i can...
thingiverse
free
Ender 6 extruder move kit by snebragd
...another to make it reach. attention: remeber that the exruder is not fastened with screws if you flip your...
thingiverse
free
RAMP 1.4 Enclosure (Proven to fit) by chumxeed
...l scad using dxf file in linear exrude statement while mine was modified to be a self contained so there is no dxf file included.
thingiverse
free
M6 Funnel Bolt - MK8 Extruder Filament Guide by nBurn
...stock extruder, try my m6 nut funnel cover - exruder filament guide. notes there are 2 versions, one with...
thingiverse
free
Robo3d Z-Carriage Drag Chain adaptor by 1stgenbrz
...running the wiring thru that chain and wire-tucking the exruder who wants to go back and undo everything to...
thingiverse
free
Basic Bowden Extruder V2 by FerociousDesigns
...this is a further iteration from my 'simple bowden exruder#39; based on the anet a8 stock extruder design but...
thingiverse
free
Elemental Coasters (Fifth Element inspired) by DasMia
..."+" showing, the other side "-" showing). instructions: single exruder print all 5 coasters and one triangle with the...
thingiverse
free
3D Drucker mit Kreuzkinematik mit 120g Direct Extruder, Nema 14 Stepper und kugelgelagertem Druckkopf auf Carbonwellen by astfaellergerald
...8 x 4 x 3mm getriebe u. extruder schrauben: exruder mit e3d v6 hotend: 3 x m3x35 senkkopf 1...
thingiverse
free
QED Hot End Cooling System with Convergence Part Cooling Nozzle for: Creality CR10 CR10S Pro V2 Ender3 Ender5 MicroSwiss E3DV6 Volcano Hotend 4010 5015 Direct Drive by magnokneeto
...others. based on center of mass considerations direct drive exruder that pass the filament to the left of the...
3dwarehouse
free
Toilet Partition Headrail
...s. includes wall or corner bracket. #anodized #bracket #dressing #extruded_aluminum #headrail #partition #rail #toilet_room #wall