25 earlynerd 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Yet another Bus Pirate Remix (Inserts Edition) by earlynerd
... edition) by earlynerd
thingiverse
lid and base split up, base modified for 3.8mm length thermoplastic m3 inserts from mcmaster!
thingiverse
free
IN-12 Nixie socket by earlynerd
.... heat from a soldering iron seats the pins the rest of the way, and locks them in. the tube helps make sure they go in straight.
thingiverse
free
Reptile S800 motor mount w/ inserts by earlynerd
...nserts. specifically mcmaster-carr part number 94180a331. the wing will need some small cuts to make relief holes for the bosses.
thingiverse
free
Realacc X210 lightweight antenna tube mount by earlynerd
...10. slides over standoffs, use a bit of double sided tape to secure to the bottom plate. fits standard 1/8" od antenna tube.
thingiverse
free
Runcam Owl HS1177 adapter by earlynerd
...nd should hold into the mount with a little bit of double sided adhesive. step file provided in case you'd like to modify it.
thingiverse
free
Rakon Tiny Whoop pico camera mount by earlynerd
... frame but may also fit the standard size one. i got the camera at readymade rc, but highly similar ones are available elsewhere.
thingiverse
free
Hive150 Antenna mount and VTX mount by earlynerd
...ideo transmitter which slides onto the horizontal standoffs behind the camera. i used a little double sided tape to hold mine on.
thingiverse
free
Hive210 VTX and receiver antenna mount by earlynerd
...attaching them to zip ties! there's also a version without the rx antenna spikes, if you prefer to mount them somewhere else.
thingiverse
free
Micro 85 Propeller Guard by earlynerd
...htly depending on material and machine. for me, 101% fits well in petg and 103% is about right in abs, but your mileage may vary.
thingiverse
free
Hive 210 underbody LED tray by earlynerd
...ight! great for making sure your quad can be seen in opponent's fpv feed.
weighs around 7 or 8g with leds when printed solid.
thingiverse
free
Saleae Logic pro 16 Analyzer dock station by earlynerd
...er in order and assists with clean cable management.
looks like the stl is upside down, print with the flat side down, obviously.
thingiverse
free
120mm fan Rostock Max side panel duct by earlynerd
... throughput and less noise than a smaller fan. the fan installs onto the duct using m3 threaded heat set inserts and 30mm screws.
thingiverse
free
Rostock Max Dual PSU panel by earlynerd
...he duet control to switch main power of both units on and off.
i use an iec y cable to power both supplies from a single outlet.
thingiverse
free
Rostock max clip on T10 LED by earlynerd
...ffiliate link)
these bulbs have bridge rectifiers on them so it makes no difference which pad you solder positive or negative to.
thingiverse
free
Realacc X210 stack offset and X4R mount by earlynerd
...the output facing forward, the band/channel leds are easily visible in the top plate cutout, and button accessible from the side.
thingiverse
free
Realacc X210 flexible 45° vtx antenna mount by earlynerd
... 2017: added 60 degree and 30 degree options for the mount! and a step file of the original to make it easier to mod if you like.
thingiverse
free
XBL117 SLY.VESTER pack by earlynerd
...ch for it to clear the rear standoff the way i wanted it to, but its easy just to solder in a jumper for sbus without the switch.
thingiverse
free
1.5mm motor shaft to 5mm propeller adapter by earlynerd
...ield tested these props yet but livingroom hover/punch test looked promising :)
edit: .sldprt uploaded too if you need to modify.
thingiverse
free
370Z B pillar finisher clips by earlynerd
... simply search for 76988-4n000. they snap right into the printed brackets, and then the whole thing pops right back onto the car.
thingiverse
free
Rostock max sorbothane dampening replacement feet by earlynerd
... abs "spring" with the sorbothane pads on the bottom of that to help absorb both lower and higher frequency vibrations.
thingiverse
free
Headplay "Sly-Versity" receiver upgrade by earlynerd
... steps and no pictures, i will update with a more detailed build guide and can answer any questions via messages in the meantime!
thingiverse
free
Runcam Owl adapter and minimosd mount for Spaceonefpv aero pod by earlynerd
...minimosd into its mounting location.
i've provided the .sldprt file, feel free to modify however you like, post remixes, etc.
thingiverse
free
Dual or single DPS-1200FB power supply mount by earlynerd
...ly free up some interior volume for the ssr and the current power panel could have a large fan in place of the current iec inlet.
thingiverse
free
Hive 150 20mm tailpiece by Tramol
...20mm tall deck height of the intrepid. thanks to earlynerd for the cool design. i wish all my copters...
thingiverse
free
Remixed X210 body with camera guard and 45 deg SMA mount by Rollerah
...with the nice 45 degree sma mount created by earlynerd together with the included additional supports, this mount has...