63 drazen 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Silverstone FT03 Case Badge by Drazen
...03 case badge by drazen
thingiverse
replacement case badge ornament for silverstone ft03 mini pc case.
v3 is slightly larger.
thingiverse
free
Silverstone FT03 PC Case Clip by Drazen
...rstone ft03 pc case clip by drazen
thingiverse
this is a replacement clip for the silverstone ft03 panel clips that break allot.
thingiverse
free
Crinkle Lamp Base by Drazen
...t with no solid top or bottom and use infill to make a partially hollow structure. i think i settled on honeycomb at ~15% infill.
thingiverse
free
Pegboard Clip by Drazen
...file is attached if you want to edit it.
here is a full collection of my pegboard stuff:http://www.thingiverse.com/thing:1486547
thingiverse
free
2013 Honda Civic Trunk Hook by Drazen
...ngiverse
this remix is scaled to fit the trunk of a 2012-2015 honda civic (this is 9th gen). confirmed to fit a 2013 civic coupe
thingiverse
free
Designer Toothbrush Caddy- 1 Brush by Drazen
...
i cut down the 2 toothbrush holder for just 1. there are a couple of minor irregularities in the mesh, but it printed out well.
thingiverse
free
Dog Crate Latch by Drazen
...ved a crate for free but it was missing all of the pins.
i included the .ipt file if you want to edit this in autodesk inventor.
thingiverse
free
Cupholders for Thor Motorcoach Axis by Drazen
...ide, and the other is passenger. they are deeper than the factory parts. can be printed upside down without any support material.
thingiverse
free
Bike Chain Guide by Drazen
...tain your chain and keep it from falling off. i wanted to run a 'standard' chain ring as a 1x without a front derailleur.
thingiverse
free
3mm nut by Drazen
...s.
if these come out too large or too small for you, consider scaling them a few %.
i printed with pla using 0.1mm layers.
thingiverse
free
Caprock Canyon Topography by Drazen
...t my similar map of palo duro canyon for an idea of what this will look like when printed!http://www.thingiverse.com/thing:606081
thingiverse
free
Fiestaware Soap Pump Repair Sleeve by Drazen
...epair a cracked pump. you may need to scale this slightly up or down depending on your nozzle and calibration. modeled in freecad
thingiverse
free
Wanhao I3 Filament Lever Catch by Drazen
...would slip off too easily on the original version. this fixed it for me.
should fit on all version of wanhao i3, cacoon, ect ect
thingiverse
free
![Wanhao Duplicator i3 - Guide Ring (Turnable Knob) [Remix from Drazen] by israngkul](/t/8812812.jpg)
Wanhao Duplicator i3 - Guide Ring (Turnable Knob) [Remix from Drazen] by israngkul
...iddle position and insert filament through this ring (can turn this ring 360 degree as needed)
thanks drazen for original design.
thingiverse
free
Nexus 5X Case by Drazen
... put it on.
i printed it with no solid bottom layers and a fun infill patter for a textured back. i only printed two top layers.
thingiverse
free
Z Axis Endstop Adjustment Duplicator I3 Wanhao by Drazen
...djusted. i did not design this- it is available on the wanhaousa website for download. i am adding it here so people can find it.
thingiverse
free
Palo Duro Canyon Topography Texas State Park by Drazen
...larger, but this print shows the part that is inside the state park. palo duro is the second largest canyon in the united states.
thingiverse
free
Star Tealight Candle Holder by Drazen
...a should work fine too.
modeled in freecad. freecad file is attached to this make. i printed with 3 walls and around 10% infill.
thingiverse
free
Dog Casting Mold by Drazen
...rill. please wear protection with this sort of project! i was wearing a face shield, long leather gloves, long pants and sleeves.
thingiverse
free
OpenRC F1 2017 Rear Axle Reinforced by Drazen
...larger to accept a #8 threaded rod. the hole runs the full length of the axle.
use a drill to help thread the rod into the axle.
thingiverse
free
Cauldron- Easy Print Remix by Drazen
...rim or leave a mark. the cauldron i show in the photo is scaled to 400%.
this is a witches cauldron / pot / halloween decoration
thingiverse
free
OpenRC F1 Rear Suspension Engine Cover by Drazen
...vement. my motor has large pins for cables to be soldered on. to clear these pins i had to thin out a section of the motor cover.
thingiverse
free
OpenRC F1 Rear Fin 2017 by Drazen
...bility, but any material will work.
update 3/4/17: added a new version of the fin. it is a little shorter and has some chamfers.
thingiverse
free
3DRC Bumpers for RC Car by Drazen
... other version mounts over the carrier.
the rear bumper is a modified version of the original. it has more coverage of the motor.
thingiverse
free
Simple Advent Calendar With Star by Drazen
...ck of the tree to hang it from a hook.
i forgot to take photos before i gave it to someone... i'll try and get photos later.
thingiverse
free
Spool Hanger for Closet, Wanhao by Drazen
...re "through" so you can either thread the bolts into the plastic and use the stock bolts or use longer bolts with nuts.
thingiverse
free
Ikea Grundtal Towel Rack Knob by Drazen
... the glue adhere.
for color and smooth texture, i painted them with white 'hammered look' spray paint. three light coats.
thingiverse
free
Openrc F1 Rear Suspension Pivot by Drazen
... the correct bushing size so i did not model this... you could get away with using a bit of tape rather than a bushing if needed.
thingiverse
free
XTR M960 Chain Guide by Drazen
...ty calf laceration on them after a fall. as such... i tend to run a bash guard instead of the outer large ring whenever possible.
thingiverse
free
OpenRC F1 Wheels for F103 Tires by Drazen
...he tire to ensure they stay in place but you might get away without this. the tires fit well with no glue- especially the fronts.
thingiverse
free
Bulbasaur with More Dirt, Low Poly by Drazen
...e the model shown in photos is 4x scale.
i also upgraded the drainage a little bit. the idea it to make bulbasaur a passable pot!
thingiverse
free
Bike Cable Plug for Internally Routed Cables- YT Jeffsy by Drazen
...o in a ~12x6mm oval shaped hole.
must be printed with flexible filament to work. i used a really soft tpe. ninjaflex would work.
thingiverse
free
Duplicator i3 feet: Foam Remix by Drazen
...place but this probably wasn't necessary.
printed with pla @200c with 0.15mm layers. currently i have 6 of them installed.
thingiverse
free
Bike Handlebar End Cap (Mountain) by Drazen
...go embossed
not split, yes embossed with logo
yes split in side, yes embossed with logo
yes split in side, not embossed with logo
thingiverse
free
Strong Pegboard Accessories by Drazen
...uot;roughneck" shed had just 4 hangers for a 2x4 ft pegboard. i added 8 more mounts using these spacers and 1/4 inch screws.
thingiverse
free
YT Jeffsy Bike Chain Guide by Drazen
...t i started from scratch and reshaped the whole thing. mine is printed with sls nylon, but i think fff could also make this work.
thingiverse
free
OpenRC F1 2017 Front Chassis by Drazen
...so has a little opening in the side to allow a wire to pass through. i use this to mount the power switch on the side of the car.
thingiverse
free
X Cable Chain Relief- Duplicator i3 Wanhao by Drazen
...h to pull on the cables constantly. i was afraid of an eventual failure...
this upgrade will require 2 m3 ~5mm screws and nuts.
thingiverse
free
OpenRC F1 2017 Wings by Drazen
...dated model has not been uploaded.
update: 2/26/17 (2): new models uploaded for front wing.
update 3/12/17: new front wing design
thingiverse
free
Duplicator i3 Lamp Mount by Drazen
...roducts/20169658/
if you want to mount this on the other side or use two lamps make a mirror image of the model with your slicer.
thingiverse
free
Birdhouse, Easy Print, No Support, Mid-century by Drazen
...s it shallower, but wider.
this will print without any supports.
i included the inventor files so it can be edited if you like.
thingiverse
free
3DRC Upgrades by Drazen
...ink r- strengthened
rear hubs- strengthened
i'll probably add more parts as i break things and decide they need improvement.
thingiverse
free
Manitour Mars Damper Repair Parts by Drazen
...
let me be honest- this turned out much better than i would have guessed on a first try... but time will tell for the durability.
thingiverse
free
Bike Bash Guard for ISCG05 tabs by Drazen
...cg mounting tabs.
update 3/23/19:
added another file designed by vshen116. this works with a 32t oval:
bashguard_32t_vshen_v1.stl
thingiverse
free
Squirrel Piggy Bank (coin bank) by Drazen
...n you open these files in repetier it might say it is non-manifold. i sliced them using standalone prusa slic3r without problems.
thingiverse
free
OpenRC F1 Nose with S-duct by Drazen
... has increased ground clearance under the front wing. no more 'nostrils' on the front- just a smooth. retains the s-duct.
thingiverse
free
openrc F1 2017 Tires with Studs by Drazen
... me a week or 2 and i'll have them tested!
i print the tires with just two walls and 0% infill. 1mm top and bottom thickness.
thingiverse
free
Bike Steerer Tube Storage Plug by Drazen
... used two nuts but there are a few ways you could do this. print the wing nut if you want to make it 'tool-less' to open.
thingiverse
free
Duplicator i3: Top Mount Spool Adapter by Drazen
...3 outer shells. 4 layers on top/bottom. i had to slightly enlarge the holes on the steel bracket with a drill bit by hand to fit.
thingiverse
free
Bike Cable Plug for Internally Routed Cables- YT Jeffsy by Drazen
...ble because it is split in 1 side.
more 3d printed bike parts, including metal ones, here:https://www.instagram.com/nickb_makes/
thingiverse
free
Front Suspension OpenRC F1 - flexible filament by Drazen
...lternative you can just trim the normal part with a razor blade or leave it as-is. this chassis has a couple of other tweaks too.
thingiverse
free
Wanhao Duplicator i3 Filament Guide Tube Adapter by Drazen
...with a slightly smaller hole. file name is now filguide4mmv2.stl
update 10/18/15:
updated 4mm tube holder with repaired stl file.
thingiverse
free
Duplicator Z axis brace top cover filament guide tubing mod by Plastic_Innovations
...filament guide tube adapter by drazen. print one of drazen#39;s guides filguide4mmv2.stl for the extruder, and make this for...
thingiverse
free
Nexus 5x Fire Hydrant Case by RappmanD
...rappmand thingiverse remix of mb20music's fire hydrant (https://www.thingiverse.com/thing:148256) and drazen#39;s nexus 5x case...
thingiverse
free
2012 Honda Civic Bag Hook by JimAlex
...bag hook by jimalex thingiverse original design taken from drazen thingiverse no: 1514035. redesigned to fit 2012 honda civic...
thingiverse
free
Wanhao / Maker Select V2 7/16 Flex Lamp Mount by Armstrongbc
...mount holes on the duplicator i3 lamp mount by drazen but the hole placement and size wouldn't do for...
thingiverse
free
Wanhao Duplicator i3 Filament Guide Tube Adapter 4mm by Jeffeb3
...adapter 4mm by jeffeb3 thingiverse based on this (obviously, drazen gets all the credit) http://www.thingiverse.com/thing:877258. but the 4mm version...
thingiverse
free
USB cable holder for pegboard by fDutchman
...so i used tinkercad to make a remix with drazen#39;s pegboard hook that fits my pegboard perfectly. extended the...
thingiverse
free
Monoprice / Wanhao Duplicator i3 upgrade - replacement x-axis cable drag chain starter link by rasarmg
...same issue, however, each require additional mounting hardware: by drazen published jun 17, 2015 by antscran, published feb 17,...
thingiverse
free
OpenRC F1 2017 Front Suspension - flexible filament by Torandi
...update parts with the design and flex block from drazen#39;s suspension. video of the suspension: https://www.youtube.com/watch?v=x9xcfjb56qk i printed the...
thingiverse
free
Wanhao Duplicator i3 IKEA JANSJÖ Bottom Mount by Luddy
...i3. i modified the duplicator i3 lamp mount by drazen concept by moving it to the bottom of the...
thingiverse
free
OpenRC F1 Front Suspension Servo Saver Solution by marcotheboy
...2 versions of the front suspension mod: https://www.thingiverse.com/thing:2069719 (by drazen https://www.thingiverse.com/thing:2282773 (2017 version by torandi) (the photo shows it...
thingiverse
free
Wanhao Duplicator i3 v2.1 PTFE Filament Guide and Mount (compatible with z-braces mod) by FChamberlain
...remix of herman_pid's filament guide remix here https://www.thingiverse.com/thing:904146 and drazen#39;s ptfe tube mount here https://www.thingiverse.com/thing:877258 i noticed there were...