20 dissifilo 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Test Nut Set by dissifilo
...test nut set by dissifilo
thingiverse
just for test.
3 pieces can combined together.
thingiverse
free
Print Test by dissifilo
...print test by dissifilo
thingiverse
infill 15% at least 填充最低限制
層高建議使用layer height 0.06~0.1mm
初始層高使用first layer height 0.1~0.15mm
thingiverse
free
CR-10S5 Leveling Knob Aid 熱床平衡調整鈕 by dissifilo
...filo
thingiverse
i've moved to cults~ please download therehttps://cults3d.com/en/users/trunkey/creations
我已搬遷到寇特網，請前往觀看更多檔案
thingiverse
free
APPLE Deco 蘋果得口 りんご林擒Ringo by dissifilo
...蘋果得口 りんご林擒ringo by dissifilo
thingiverse
蘋果appleりんご
hollow inside 內部空心
可用15~100%infill填充
support indeed必須使用全支撐
good luck!
祝好運!
thingiverse
free
CR-10S5 Leveling Knob 熱床調整鈕輔助塊Aid 1.0 by dissifilo
...filo
thingiverse
i've moved to cults~ please download therehttps://cults3d.com/en/users/trunkey/creations
我已搬遷到寇特網，請前往觀看更多檔案
thingiverse
free
HappyRabbit俏耳兔兔 by dissifilo
...p; 底部bottom(選擇性開啟optional)
層高layer height: 0.1mm
壁厚wall thickness: 0.7↑
now there are a fat rabbit and a smaller one.
檔案中有肥兔和小兔兩種
thingiverse
free
Card Stand Test Cube列印測試方塊名片座 by dissifilo
...issifilo
thingiverse
card stand test cube
列印測試方塊名片座
infill填充: 15~20%
layer height層高: 0.1%
speed速度: 80mm/s
duration列印時間: 42min~1h
thingiverse
free
(Testテスト) Spiral & Slope Test 斜面與螺紋測試組 by dissifilo
...hingiverse
just try the scale change to test if your machine has extrusion or moving inaccuracy
運用螺紋與斜面測試尺寸誤差，測試出組合件所需要調整的比例縮放數值
thingiverse
free
The Failed Fidget Spinner 失敗的指尖大陀螺 by dissifilo
..., you have to adjust first layer height percisly.
檔案製作尺寸是 16.5公分寬
如果真的要手指玩的尺寸，必須縮小到35~45%的大小，才會是手指上的七公分大小。
縮小後建議填充100%，才有足夠的旋轉質量。
thingiverse
free
Functional Trancated octahedron test cube截角八面體測試塊名片座 by dissifilo
... could be a card stand, or a piece of note paper chop as well.
填充infill: 15% up以上
線寬line width: under 0.6mm
層高layer height: 0.1mm
thingiverse
free
203040 Calibration Step 校正階段塊 三階校正塊 by dissifilo
... 60mm help you to modify x y plane axis free spacing
accumulation.
三段高度20 30 40mm和三段寬度20 40 60mm幫助你計算出累計的實質誤差，藉以調整馬達步數，或是抓出零件游離間隙
thingiverse
free
M5 Hex Nut Knob Shell M5螺絲螺母輔助殼 by dissifilo
...t tools.
quite helpful for m5 hex nuts,
you can scale it for other size nuts,
hope you enjoy it!
手轉輔助m5螺絲螺母外殼，
可自行縮放符合其他尺寸
希望你會喜歡
thingiverse
free
Thorn Pike Pad Poke 刺刺林 處罰墊 by dissifilo
...回痛感/解緩痠痛感，用來按摩或是替人消災解厄都很適宜。
80~100% infill填充率
if you felt over pierced, please lower the ratio of z height.
可以藉由z軸比例高度調整，變化尖刺的高度喔
thingiverse
free
CR-10S Left Side Fan Rack by dissifilo
...，則需要手動以工具貫穿，噴風口長度可手動裁剪。
(有大約五度角傾斜空間可調整噴風高度)
如果安裝發現和左上角滾輪螺絲有空間上的抵觸，請使用墊圈偏移位置。
或可使用rack2第二種較厚的形式直接安裝，而不用墊圈來調整位置。
有設計上的問題請通知我，
使用愉快。
thingiverse
free
創吉藝Edge Hook for Scooter 三陽SYM發財高手 機車前箱掛勾 by dissifilo
...%↑ ~100%
layer height 層高0.3mm↓
nozzle噴嘴 0.8mm↓
scale: 80~150% 比例最好介於0.8~1.5倍
for you hanging drinks or something more
用來掛飲料甚麼的都好用
thingiverse
free
Note Paper Sticker Clip 便利貼 紙張夾 備忘錄 by dissifilo
...cale 125%
填充infill: 100%
耗時time elapse: 5~7min
層高layer height: 0.1mm
no support不需要使用支撐
it worked, confirmed already.
真的可以用，已經實驗過了
thingiverse
free
Mobile Cellphone Lying booth Site 5吋手機座 by dissifilo
...讓你的手機有地方躺著看電影，或許放大一點也可以讓平板跟著躺。
建議填充使用0.4~0.6mm 線寬 作30%的三角形內部填充，
外壁用0.6~0.8mm厚度，讓它保持一點點的彈性。
不需使用支撐，請將物件擺正底部朝下，平放在床板上再切片列印。
希望你會喜歡。
thingiverse
free
Missile 味噌 みそ 火箭 Rocket grenade by dissifilo
...ayer 5~10
第5~10層時建議吹冷風量調到100%
if any trouble occurs while your 3dp geeing, pls inform me informally.
要是任何問題發生在打印的ㄐㄓ聲當中，都可以反應讓我知道喔
thingiverse
free
(Failed失敗版)CR-10S E3D Titan V6 Volcano Direct Drive Extrude Set_v1 火山噴嘴近端擠出 by dissifilo
...cting e3d-titan mount and the top of heatsink, this distance is helpful for retraction.
另外還需要減一小段鐵氟龍管來接泰坦座底部和散熱管上端，作為擠出回抽的線材緩衝空間。
thingiverse
free
CR-10S E3D V6 Volcano Titan Direct Drive Extrude 火山噴嘴近端擠出 Set_v2 by dissifilo
...retraction.
另外還需要減一小段鐵氟龍管來接泰坦座底部和散熱管上端，作為擠出回抽的線材緩衝空間。
i choose e3d titan clone from china, setting is 1674~1680 steps/mm 我的馬達步數設定