28 curioustech 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Wire Clasp by CuriousTech
... curioustech
thingiverse
yet another wire clip. push a straight pin through the hing and clip off.
v2 uses a 2mm plastic screw.
thingiverse
free
Align TRex 150 Tail Fin by CuriousTech
...align trex 150 tail fin by curioustech
thingiverse
replacement tail fin for a trex 150x. 100% infill.
thingiverse
free
Wire Magnets by CuriousTech
...take any round magnet, enter the mm diameter and length, and print. add .3 to the diameter, and subtract about 2 from the length.
thingiverse
free
Parametric push pin by CuriousTech
... pin size, base thickness and height. it works with 0.15mm resolution. probably loose in 0.1mm, so 0.4mm space would be better.
thingiverse
free
Blade 400 landing gear strut by CuriousTech
...ut by curioustech
thingiverse
remixed/resized from the original, and holes moved. also added skid end caps since they were easy.
thingiverse
free
Anycubic i3 MEGA TUSH remix by CuriousTech
...
thingiverse
tush remix for the i3 mega gantry. print part 1 with a brim. i haven't used it yet. very nice for quick change.
thingiverse
free
Gaui 200 landing gear strut by CuriousTech
...ich is a remix, just shrunk and the holes moved. it's taller than stock, so print 2. use supports. more infill is stronger.
thingiverse
free
Panasonic ER-GB80 Wall Holder by CuriousTech
...nger for a mirror and brush at the end that don't really work well there.
50% infill which could be much lower. no supports.
thingiverse
free
APS996 Remote Battery Cover by CuriousTech
...better, and i'll rework it later.
updated: all good. the lip at the end has a bad overhang, but just needs scraping a little.
thingiverse
free
TRex 150 Landing Gear by CuriousTech
...s to press the struts into the frame.
the stock one was 2.1g and this is 3.8g total, so it's a bit heavier but much stronger.
thingiverse
free
Socket Sleeve scratch protector by CuriousTech
... nothing else needed.
use openscad to create any size. this adds a wall thickness to the original, but seems to work well at 1mm.
thingiverse
free
Lemarchand's Fidget Configuration by CuriousTech
...t)
one 608 bearing
half dozen or so turtured souls
the scad is also available if you want to fidget with the numbers or remix it.
thingiverse
free
Tools on rails (modular) by CuriousTech
...some don't, or cause extra pain, like the horizontal tape holder. it broke loose half way through without an adhesion skirt.
thingiverse
free
12V 8AA to 3 14500 Li-Ion adapter by CuriousTech
...prings or 9v clips would probably be better. add foam to hold it in devices that can shake around because it's half the size.
thingiverse
free
GoolRC G90 Pro case and parts by CuriousTech
...s (piano wire or an old 450 flybar)
there's also a tpu foot and battery holder, and camera mount i made at 15 and 18 degrees.
thingiverse
free
Anycubic i3 MEGA Bed Cable Guide by CuriousTech
... made it too close for a larger knob. i guess i should add the knob since it's pictured. it's smaller than some others.
thingiverse
free
Trans Am WSQ Grill by CuriousTech
... for supports (and raft if needed). it's an even thickness, a bit larger, and mounts easier, plus the hex design was rotated.
thingiverse
free
Milwaukee M12 Battery by CuriousTech
... other 2 need 10k resistors. the resistors (1/16w) were meant to fit into the holes vertically, so the leads become the contacts.
thingiverse
free
Anycubic i3 MEGA SD card flipper by CuriousTech
...ust make sure the front 2 lower screws aren't touching components on the card slot pcb. it shouldn't be a problem though.
thingiverse
free
TriggerCap (AirSoft) safety cap by CuriousTech
... sunlight or heat, becoming weaker over time, not being used properly, or breaking/coming off from dropping the (airsoft) weapon.
thingiverse
free
i3 Mega Micro Filament Sensor by CuriousTech
...nc-subminiature-micro-switch-w-lever-roller-5pcs-s7p7/172667598181?sspagename=strk%3amebidx%3ait&_trksid=p2060353.m2749.l2649
thingiverse
free
Smart Bearing Block remix by CuriousTech
... and smooth.
when assembling, leave it loose enough to fit the rod in without force, then tighten down until there's no play.
thingiverse
free
Desk Magnifier Mod by CuriousTech
...ke this as thin as i could. it only has 3mm of space in the back part.
update: led_ring_v2 has no bevel so the lens fits tighter.
thingiverse
free
Anycubic i3 MEGA Chains by CuriousTech
..., or touch the bed leveling knob, and reaches the full range.
edit: z_topright is actually the bottom swivel link for both sides.
thingiverse
free
Anycubic i3 MEGA Rear Blower by CuriousTech
... side some, so it can't fully travel to the right of the bed, unless the mount is cut off. it's about 8 mm from the edge.
thingiverse
free
Anycubic i3 Mega Spool Holder by CuriousTech
...opening. then the adapters should be a quick print, and have some space at the flex point between the inner ring and outer tabs.
thingiverse
free
Anycubic i3 Mega Spool Holder
...upgrade version of "anycubic i3 mega spool holder" by curioustechquot;. this one is thinner and with fewer parts(uses original...
thingiverse
free
AnyCubic Chains Simple
...anycubic chains simple thingiverse this is a remix of curioustech#39;s chains. his build had imop way to many different...