62 cfeniak 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Corner Shelf by cfeniak
...cfeniak
thingiverse
corner shelf, sectioned into pieces to fit on my 8"x12" bed. printed in pla, attached with epoxy.
thingiverse
free
Tornado Foosball Rod Holder by cfeniak
...tornado foosball rod holder by cfeniak
thingiverse
used for holding rods for practice shots or goalie wars.
thingiverse
free
Rain Diverter Concept by cfeniak
...nspout to divert rain water to rain barrel.
*** this is a concept only, please use model as inspiration for further development
thingiverse
free
ZMR250 Cable Catch by cfeniak
... power and balance charge cables away from the props. 2mm and 3mm version. best printed in something flexible like abs or petg.
thingiverse
free
Multistar Baby Beast Motor Bell Wrench by cfeniak
...multistar baby beast motor bell wrench by cfeniak
thingiverse
makes removing nyloc prop nuts easier
thingiverse
free
Bowden Tube Holder Accessory by cfeniak
...t with two m3 bolts at 10mm spacing. guides the bowden tube. longer one is the one you need to go with the extruder i designed.
thingiverse
free
Shorter 30mm Fan Shroud for Pico Hot End by cfeniak
...shorter 30mm fan shroud for pico hot end by cfeniak
thingiverse
30mm fan shroud for the pico hotend. print in abs.
thingiverse
free
Big Guy Statue Split by cfeniak
... slic3r. exported as individual files. much more printable, but still needs support.
see source references in original version.
thingiverse
free
Stepper motor feed knob by cfeniak
... designed for use with direct drive filament setups for manually feeding filament. push fit. smaller sized knob is big enough.
thingiverse
free
Fluval Flex aquarium lid prop by cfeniak
...niak
thingiverse
simple lid prop i designed to hold up the fluval flex 32.5 gallon / 123 liter tank lid during maintenance, etc.
thingiverse
free
15mm extrusion open ramps mount by cfeniak
...3mm screws. for use with ramps and 15mm open beam extrusion. designed for use on ob1.4 printer but will work on similar setups.
thingiverse
free
ZMR250 Camera Mount by cfeniak
...y a long m3 bolt right behind the camera. this file is more vibration resistant as the small camera side bolts can easily strip.
thingiverse
free
Countertop Compost Bin by cfeniak
...ers with an 8"x8" or larger print bed (actual footprint is 180mmx180mm). it can also be fully printed with no support.
thingiverse
free
PSU Fan Exhaust Duct by cfeniak
... to exhaust mine out the side instead of the front/back. i added a mirrored version to work in the original orientation as well.
thingiverse
free
Video Game Frame by cfeniak
...515 openbeam aluminum extrusion comes in normal or black.
got mine here:https://solarbotics.com/
just search "openbeam"
thingiverse
free
WaveOnWave Tablet Stand by cfeniak
...our tablet.
while designed for the ipad air the slots are large enough for thicker tablets too.
enjoy and please post your makes.
thingiverse
free
5/16 (8mm) Pastry Icing Bag Nozzle by cfeniak
...iverse
this was designed to make macarons. nozzle tip is 5/16 inch or 8mm in diameter. simple cone with slip ring to hold bag.
thingiverse
free
Mini V Slot Wheel 1/4" spacer by cfeniak
...cer for v slot mini v wheel. print in sets so that they are equal in length (to compensate for inconsistent first layer squish).
thingiverse
free
B3 Pico Hot End 30x30mm Fan Shroud by cfeniak
...for use with the pico nozzle and a 30mm fan. print in abs only. pla is too brittle to make the spread and can handle less temp.
thingiverse
free
Tornado Foosball Rod Holder, single by cfeniak
...s. print as is in pla, no supports needed. there is a large bridge but it shouldn't be a problem if you have a cooling fan.
thingiverse
free
Toilet Paper Holder by cfeniak
...sh so that the lid pattern remains. i had too much on my first print shown here, but reduced it on later ones and it looks good.
thingiverse
free
IPad Air Base 3 Position Static Stand by cfeniak
... 3 position static stand, no moving parts. very stable in all orientations except the middle slot for the tall/long orientation.
thingiverse
free
OB1.4 End Stop Mounts for prusa mod (45mm) by cfeniak
.../thing:302416
x/y bases are just a collection of:http://www.thingiverse.com/thing:273711http://www.thingiverse.com/thing:276229
thingiverse
free
ImmersionRC 5.8Ghz Audio/Video Split Transmitter Case (25mW) by cfeniak
...0mw version for the central antenna mount of 25mw vtx. split the object with your slicer if you want to print on half at a time.
thingiverse
free
OB1.4 Direct Feed Filament Stand, Cantilevered (for 15mm extrusion) by cfeniak
... rod and
-8mm bearing with some type of holder
ex: http://www.thingiverse.com/thing:80580
http://www.thingiverse.com/thing:49250
thingiverse
free
ImmersionRC 2.4Ghz Audio/Video Split Transmitter Case (700mW) by cfeniak
...ed 5.8 ghz case and relocated dip switch access.
updated version with correct dimensions:http://www.thingiverse.com/thing:1269670
thingiverse
free
5mm to 8mm Z Coupling by cfeniak
...he fly 1st layer height adjustment.
update: added files with alternate diameters for the 5mm end. 7mm to 5.5mm. see file names.
thingiverse
free
Split Downspout Rain Diverter for Rain barrel by cfeniak
...e lower section of the water bypass portion around the downspout tubing
i used a 2 part epoxy to attach the pieces after printing
thingiverse
free
60mm ID Filament Roll/Spool Support for 8mm bearing by cfeniak
...y to print. bearing is press fit for 22mmx7mm. heat bearing housing surface with a lighter to make the bearing press in easier.
thingiverse
free
Various 20x20 V-Slot Extrusion Brackets by cfeniak
...nt depends on how the extrusion butts up to the piece.
note: corner piece holes are printed to 1mm on purpose. drill out to 5mm.
thingiverse
free
ImmersionRC 5.8Ghz Audio/Video Transmitter Case (600mW) by cfeniak
...s. adds flat surfaces to velcro to.
check out my new design for better antenna support:http://www.thingiverse.com/thing:865127
thingiverse
free
Direct Drive Bowden Extruder; MK8 version by cfeniak
...e to motor base to reduce cantilevered load on motor shaft
-tensioning bolt catch is slotted to allow quick release functionality
thingiverse
free
C-Bot 3D Printer by cfeniak
... none the less, you can see printed parts like corners and tees that can be replaced with items from the open builds parts store.
thingiverse
free
1.75mm Filament Cleaner / PLA Oiler Accessory by cfeniak
...addition. print in place hinge allows the container to pivot for alignment but also be moved out of the way if switching to abs.
thingiverse
free
ImmersionRC 5.8Ghz Audio/Video Split Transmitter Case (600mW) by cfeniak
...ectrical tape so that they wouldn't interfere with my velcro.
make sure the zip tie at the connector is as tight as possible.
thingiverse
free
Beersbee Topper by cfeniak
... need many more wraps to get a good fit to the inside of the pvc
frisbee and beer not included. please beersbee responsibly. ;)
thingiverse
free
M5 Jam Nut Catch for 20mm V Slot by cfeniak
... over tightening the bolt can cause shear failure (as opposed to bending) of the extrusion edge... also don't over tighten ;)
thingiverse
free
Pivoting LCD frame for 20 mm extrusion by cfeniak
...r m3 nut.
if you need modifications let me know.
update 2015/08/28 added modified version made by elmo clarity (openbuilds tag)
thingiverse
free
M300 Quadcopter by cfeniak
...!)
6040 or 6045 otherwise
m5 nyloc nuts and washers for props (unless you have multi direction threads or a different size mount)
thingiverse
free
Multi Use Stand by cfeniak
...ottom by bolting on some steel flat bar to the 2020 aluminum. it requires flat bar, t-nuts, and the appropriate length m5 bolts.
thingiverse
free
Direct Drive Bowden Extruder for 20 mm extrusion by cfeniak
...per driver for 3mm filament. they can be found on ebay. just make sure they can still mount on the normal nema 17 bolt pattern.
thingiverse
free
OB1.4 Direct drive, direct feed extruder for 45mm X axis by cfeniak
...d pulley
long m3 bolt and nut (or knurled thumb nut)
spring
m3 bolts to mount motor
m3 bearing for idler w m3 bolt for attachment
thingiverse
free
Assassin Creed Belt Buckle by cfeniak
...o finish the job and for a brighter metal appearance redo key areas (the first rag will have a lot of black in it)
-let dry fully
thingiverse
free
Toilet Paper Holder by alexose
...toilet paper holder by alexose thingiverse no changes to cfeniak#39;s design. i just split the two pieces into separate...
thingiverse
free
ZMR250 Chop Spacer and Adjustable Angle Camera Mount (25mm housing) by cfeniak
... bolt behind the camera to clamp the sides. better vibration resistance. leave the camera side bolts in place to act as pivots.
thingiverse
free
Rain Barrel Water Diverter for 2-5/8" square downspout by cfeniak
...the downspout pipe. i used a ring of caulking which the lower pipe sealed against.
update 03/2015: survived the first winter!
thingiverse
free
Rotated Snowball Maker by Bomark
...by bomark thingiverse derivative of snowball maker by walter. cfeniak suggested printing the snowball maker with one of the...
thingiverse
free
IRC 2.4GHz 700mW Case by prjoe
...measurements provided were incorrect. credit and thanks to designer cfeniak ...
thingiverse
free
1.75mm Filament Cleaner/Oiler Bracket for Wanhao i3 by Mk42Workshop
...i3 by mk42workshop thingiverse this is an addition to cfeniak#39;s filament cleaner/oiler, found here: http://www.thingiverse.com/thing:482043 it is a bracket...
thingiverse
free
Cbot DBot Rear Idler - Extra Z by StefTheo
...ak_eric" the main change from the original design of cfeniak / ak_eric is the invertion of the orientation of...
thingiverse
free
Wall/Door mount for Countertop Compost Bin by mdietz
...a door/wall mount for the "countertop compost bin" from cfeniak i printed the original bin as well as the...
thingiverse
free
Y 3 Wheels Guide v2 by StefTheo
...a 4-wheel system. an other remix for d bot (cfeniak / spauda01 / nickrimmer) . just few changes from...
thingiverse
free
CoreXYbedmount by Dre363
...thingiverse designed to be used for corexy http://www.thingiverse.com/thing:500041 by cfeniak bed mounts very loosely based on a design by...
thingiverse
free
Triple C-Bot by TheDirector
...with components and ideas from: c-bot 3d printer by cfeniak (rework files)triple c-bot on openbuilds psu mount by carlsenlcd...
thingiverse
free
D-Bot Core-XY 3D Printer by spauda01
...all credit for the original c-bot design goes to cfeniak thanks to those who contributed at...
thingiverse
free
Rain Water Diverter by Matterthings
...rain water diverter by matterthings thingiverse improvement to cfeniak elegant and clever rain water diverter. (thing:351234) now you...
thingiverse
free
Extruder Knob / Dial by robertwallace
...extruders is not accessible. this thing was inspired by cfeniak#39;s stepper motor feed knob (http://www.thingiverse.com/thing:474394). i liked the design,...
thingiverse
free
Rain Diverter Improved by kendallb
...will modify it as needed. enjoy and thanks again cfeniak for the...
thingiverse
free
Bottom Crank Heart Gear by jneilliii
...one is taller to reduce the gap, thanks to cfeniak for pointing this out. the original upload was a...
thingiverse
free
C/D-Bot Direct Drive X-endstop Mount by pizzachef
...c/d-bot direct drive x-endstop mount by pizzachef thingiverse cfeniak created a direct drive version of his x-carriage to...
thingiverse
free
PowerBot 3D Printer by PowerPlayground
...all credit for the original c-bot design goes to cfeniak thanks to those who contributed at http://www.openbuilds.com/threads/c-bot.726/ the changes...
thingiverse
free
2-5/8" Cork downspout by shivinteger
...[2] thing url : http://www.thingiverse.com/thing:351234 [2] thing author : cfeniak [2] thing licence : creative commons - attribution -...