26 bobdavis73 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Arduino Ramps 1.4 Mount by BobDavis73
... mount ramps/arduino in or to hold the top on the base, access hole for display cables. i hope someone can find this useful.
bob
thingiverse
free
Delta Counterbalance by BobDavis73
... pulleys are sized for para-cord. if you use the corner tap an m5 thread into the center of the aluminum extrusion for mounting.
thingiverse
free
MKS 3.2 Verticle Mount for a delta printer by BobDavis73
...or easy access to the wiring as well as cooling. this design has slots for sd cards as well as two openings to store drive keys.
thingiverse
free
12864 RepRap Discount Full Graphic Controller by BobDavis73
...r/button diameter. there are several versions of this board around and more than none button design. i hope you find it useful.
thingiverse
free
Optical Switch Holder and vertical slide flag by BobDavis73
.... you can file the top of the flag to raise the position or shim the switch block down to lower it. i hope you find it helpful.
thingiverse
free
Wire Traps by BobDavis73
...ving made one yet so i hope it fits your 20/20 extrusion ok. edit: i have made them now and they work great in 2020 extrusions.
thingiverse
free
Corner Stabilizer Bracket by BobDavis73
...rackets maintained the precision of the bed through all of that. i must admit i was surprised. i hope it works as well for you.
thingiverse
free
Wire Clip by BobDavis73
...onal wires. i have not yet tried the longer ones so they may be a problem printing without a skirt on the base for bed adhesion.
thingiverse
free
Center column mounted Display Console by BobDavis73
...either of the designs yet. there may be issues i have not addressed. it is a work in progress though i think it is a slam dunk.
thingiverse
free
Proximity switch holder/fan combo by BobDavis73
... fan and printed abs without any melting of the end of the nozzle. hot end maximum temperature tried without the fan on is 245c.
thingiverse
free
Reel Holder for Mega Kossel by BobDavis73
...ck. i put bearings on mine and printed a tubular sleeve to be just under the i.d. of the spools i use. i printed this with pla.
thingiverse
free
12864 Control Panel by BobDavis73
...y to the 12864 control panel. you will note that this is set up for a 20 x 60 rail. be sure to modify this to fit your machine.
thingiverse
free
Arduino Ramps 1.4 Side Extrusion mount by BobDavis73
...to move out but i thought the latch would be a nice feature. it has a mount for a 1.5" fan on the side to keep things cool.
thingiverse
free
Table & Machine Leveler by BobDavis73
...the nuts so they don't fall out when assembling. if they end up too tight for your nuts use a soldering gun to push them in.
thingiverse
free
Octo PI & Camera mount by BobDavis73
...can see i have printed it and it works great. the camera will tilt and pan (manually). i hope someone can find this useful.
bob
thingiverse
free
Bowden hot end fan and proximity switch holder by BobDavis73
.... it has a much improved air flow as well as it has a smaller foot print so it can get closer to the columns of a delta machine.
thingiverse
free
MKS TFT28 V1.2 Vertical Rail Mount by BobDavis73
...ss you could say that it had not been fully tested but i doubt the two rectangular holes would have any ill effect on the design.
thingiverse
free
Delta Dual Extruder Flying Mount by BobDavis73
...e to the heat generated by the hard working extruder motors. pla is just fine if you mount and wire up the fan as always on.
bob
thingiverse
free
Proximity Switch holder for a REK hot end by BobDavis73
...sor wires and connect it to the npn proximities third wire. this allows the sensor to work without any resistors in the circuit.
thingiverse
free
BLTouch mount with auxiliary fan mount and hot end clamp by BobDavis73
...ct. i made mine out of abs due to the close proximity of the hot end but i have made these before out of pla without any issues.
thingiverse
free
Angular Control Panel Mount by BobDavis73
... to anyone that made this model before this edit. that was a right hand mount and the sd card slot did not have adequate access.
thingiverse
free
MLK HLK-WiFi Ver. 1.1 Mount for 2020 vertical extrusion by BobDavis73
... finds this helpful. if you have questions about the wifi board i may be of help later. right now i'm just figuring it out.
thingiverse
free
Car/Truck Mirror Monitor Mount by BobDavis73
... model. don't attempt to use pla as it will sag under the weight when the inside cab temperature rises in the summer months.
thingiverse
free
NO Cussing Kossel Motor Corner Remix by BobDavis73
...r corners made from petg for added heat stability should i choose to make it more portable. don leave pla in a hot car for long!
thingiverse
free
Delta Control Panel Top Mount with SD card storage by BobDavis73
...re don't go above the aluminum extrusion so if you have a spool mount or extruder sitting on top it will still fit up nicely.
thingiverse
free
Extruder hanger with fan and end of material switch for TFT 2.8 & 3.2 by BobDavis73
...h improved design. i didn't note before but the design also has zip tie points along the back to help manage the umbilical .