21 bob99 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Toothbrush Holder by Bob99
...oothbrush handle up to 15mm in diameter.
use it to keep the brush bristles in the open air for maximum drying between brushing.
thingiverse
free
Small Bottle Holder by Bob99
..., such as bottles for eye drops. small bottles have a tendency to tip over and this is useful for keeping them neatly organized.
thingiverse
free
Lipstick Holder by Bob99
...ot is about 24.5mm square and 35mm deep. the walls are 3mm thick.
overall dimensions: width: 60mm length: 114mm height: 37mm
thingiverse
free
Glue Stick Holder for 8 sticks by Bob99
...simple glue stick holder that is meant to make to make it easy to grab and replace glue sticks. it is 155mm long by 120 mm wide.
thingiverse
free
Tool Holder for 4 Tools by Bob99
...and organized so you know where to find them.
easy printing - just use a 0.40 nozzle, maybe a brim to keep the base from warping.
thingiverse
free
Tube Holder 4x4 by Bob99
...i intended this to be a glue stick holder but it could be used to hold tubes, cylinders or anything that fits in something round.
thingiverse
free
Meanwell Fan Silencer by Bob99
...ilter, if needed.
you will notice there is only one screw holding the silencer in place but it is enough, friction does the rest.
thingiverse
free
Toothbrush & Eyedrop Bottle Holder by Bob99
..., adds a bit of organization to your counter, keeps your toothbrush dry ... and you can move two little toiletries in one motion.
thingiverse
free
CA Glue Bottle Holder by Bob99
...ounce bottles and three slots for 1 ounce bottles. they fit my bottles but i can't guarantee the slots will fit all bottles.
thingiverse
free
Lipstick Holder 3 x 3 by Bob99
...ife's various taller lipsticks it could be useful to hold small tools such as xacto knives, screwdrivers, felt tip pens, etc.
thingiverse
free
Light Shield Hinged Flap by Bob99
...er hinge supports.
you need to print two of the "hinges". they are designed for a 4.5mm (or roughly 5/32") shaft.
thingiverse
free
Furnace Intake Screen by Bob99
...all it, spread a thin coat of goop or similar rubbery stuff on the inside rim, let it dry and then push the screen over the pipe.
thingiverse
free
iPad-1 Sound Enhancer by Bob99
...k for you.
print it "on edge". no support is needed. bridging works fine when it reaches the top of the sound slot.
thingiverse
free
T-oothpaste T-ube S-queezer - Another One by Bob99
...e table. it gives a shiny face and looks a lot better.
just slip it over the used part of the tube, slide it up and remove it.
thingiverse
free
CA Glue Bottle Holder - Larger and Improved by Bob99
...o help with placement.
measurements:
240mm max overall length
61mm wide
2 oz pockets: 55mm x 30mm
1 oz pockets: 45mm x 26mm
thingiverse
free
Marker Lights for night time RC flying by Bob99
...w to assemble. this requires some gluing and soldering and assumes some basic wiring skill and familiarity with led strip lights.
thingiverse
free
Prusa Mk2/S LCD Knob - Flared by Bob99
...to use an x-acto knife to chamfer the edge of the hole to remove the "squish factor" to help the shaft will fit easily.
thingiverse
free
Clipboard Pen/Pencil Holder - Magnetic by Bob99
...quot; in case you need one for your group.
prints fine at 0.2mm layer height and no supports.
measurements shown are millimeters.
thingiverse
free
Single Edge Blade Holders by Bob99
... balsa and paper where a diy'er would want to hold the blade at 45 degrees and press while cutting with the tip of the blade.
thingiverse
free
RC Servo Wire Holder by Bob99
... can print them as you find in the stl's or rotate them 90 degrees on the x-axis, either way works well. no supports needed.
thingiverse
free
Endoscope Holder for Rostock Max V2 by Bob99
...s about 50 minutes to print.
i used pla, but you may want to use abs depending on how much heat reaches the holder on your setup.