15 axelfrom 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Faceted containers by axelfrom
...lls i can print. at the same time i created something useful. the objects are created in 123 design. i added a lid for the bowls.
thingiverse
free
Minicraft power plug by axelfrom
...them. black/green cable is + and goes to the thick pin. place the pins in one half and mate the to pieces together with som glue.
thingiverse
free
Nut to mount the Minicraft to a Dremel Workstand by axelfrom
...inicraft in the dremel work stand. the minicraft has a very good chuck that takes 5 mm drills, it also has a very good precision.
thingiverse
free
Stackable pillboxes by axelfrom
...lution in the cylinder walls and 1.5 mm side walls giving no fill in the walls.
if you find my design useful please give me a tip
thingiverse
free
Holder for Hobbyking 12 LED Cluster by axelfrom
... might have to grind a little on the edge of the led pcb to make it fit snugly.
if you find my design useful please give me a tip
thingiverse
free
Malyan M180 Tilted Control Panel by axelfrom
...el, so if you don't like it, it can be restored to it's original state.
if you find my design useful please give me a tip
thingiverse
free
K40 Laser Inline temp sensor housing by axelfrom
...perature sensor. now the readings are correct and not affected by surrounding heat, especially radiated heat from the laser tube.
thingiverse
free
Malyan M180 filament tube holder by axelfrom
... used for the original bracket, thus no changes to the printer is necessary.
if you find this thing useful please give me at tip.
thingiverse
free
Malyan M180 X-Carriage for Flexion extruder by axelfrom
...on extruder and 24 mm linear bearings the m180 really gives good print results.
if you find my design useful please give me a tip
thingiverse
free
SDS Max drive shaft cover/protector by axelfrom
...e cover, it is essentially the same but with added support for the columns when printing. these should be cut away after printing
thingiverse
free
Spherical 3 pipe coupling for 16 and 8 mm pipes by axelfrom
... pvc. any 16 mm pipe will do, choose a pipe that will give you enough rigidity.
if you find my design useful please give me a tip
thingiverse
free
Malyan M180 Fan Holder by axelfrom
... ready to go.
from now on any problem behind the fans can be fixed in a second!
if you find my design useful please give me a tip
thingiverse
free
Malyan M180 Y--axis belt tensioner by axelfrom
... loosen the stepper motor and put in the wheel, when tension is applied to the belt will stay in the location where you have put.
thingiverse
free
X-Carve elegant dust boot / collector by axelfrom
...er the router bit and adjust the level over your material 3-5 mm.
tighten the knobs so the collector is fixed.
start the carving.
thingiverse
free
Malyan M180 and Flexion Dual Extruder X-Carriage by Heliart
...x-carriage by heliart thingiverse i redesigned the x-carriage from axelfrom because i liked to use the igus rj4jp 01-08...