22 altermac 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
ZMR250 VTX-Holder universal by altermac
...e design. use a zip-tie to fix the vtx on the holder. you need to cut out the top-plate of a zmr250 to make room for the antenna.
thingiverse
free
Quad-/Tricopter Landing Gear 50mm by altermac
... with two zip-ties. it will lift the arm by 50mm. with a hard landing you only break the zip-ties. the 10mm leg weights about 4g.
thingiverse
free
ZMR250 Quadrocopter Landing Gear ziptied by altermac
...h by moving on the ziptie.
i created this version after some hassle with the screwed-version. i printed a flexible set with tpu.
thingiverse
free
CC3D Atom mount - glue in by altermac
....com/thing:526082), you need an opening in the body of your thing (plane or copter) to access the usb. check this before glueing.
thingiverse
free
Wrench for Sunnysky 2216 1250KV by altermac
...with pla although this might be to weak if you pull yout nut really tight. in this case use 100% infill to get a stronger wrench.
thingiverse
free
Hinge for R/C-plane by altermac
...your model.
there is another hinge for r/c-plane without holes. use that one when you glue your hinge to the surface of the wing.
thingiverse
free
VTX-Holder for ZMR250 by altermac
...ttp://www.thingiverse.com/thing:1266000
the et25-holder fits behind the led-spacer from http://www.thingiverse.com/thing:1599750
thingiverse
free
LED-Riser for Eheim classicLED by altermac
... ca (superglue), the other is put together with m3x16mm screw and m3-nut. there are three holes for m3 screws, you need only two.
thingiverse
free
Motor-wrench for Multistar Elite 2216-920kv by altermac
...another wrench for sunnysky 2216 1250kv motor ( https://www.thingiverse.com/thing:4661718 ) wich ist often used for a mini talon.
thingiverse
free
ZMR250 Quadrocopter Landing Gear by altermac
...oose once in a while, so pla is your eco-friendly choice.
v3.2: stronger sphere, older version was a bit thin for rough flying...
thingiverse
free
CC3D Atom mount by altermac
...//www.thingiverse.com/thing:1599750 to mount the screws thru both bottom plates. it makes live easier, when working with the pdb.
thingiverse
free
Realacc X210 motor protector or cover by altermac
... on the motorshaft and bearings. fix and pull it tight with a 3mm ziptie.
print it lying flat as in the stl-file. use pla or tpu.
thingiverse
free
ZMR 250 LowRider by altermac
...ike: when using all screws and locknuts for the arms it's a pain to remove the upper carbon to get a hand on the electronics.
thingiverse
free
Stack your RX on CC3D Atom flightcontroller by altermac
...ersion may fits also to other fcs.
maybe you also like the complete stack for cc3d atom: http://www.thingiverse.com/thing:1684887
thingiverse
free
ZMR250 Quadrocopter Spacer-Set 3mm by altermac
...ers. use m3x10mm-screws to fix the posts and pdb/flightcontroller, now you can unmount your fc without opening the bottom plates.
thingiverse
free
ZMR 250 motor-protector zip-tied by altermac
...s all motor screws. no dirty hex-screws, no mud on the motorshaft and bearings.
print upright as in the stl-file. use pla or tpu.
thingiverse
free
Tricopter Motor Tilt by altermac
... with called '...servohorn' when the universal_tilt_motor without splines doesn't work for you.
does it work for you?
thingiverse
free
ZMR250-X LOS-Trainer by altermac
...e http://www.thingiverse.com/thing:1905550 as motor-protector.
auw of my build is 417g with 3s 1300 mah and 448g with 4s 1300mah.
thingiverse
free
FPV Set for PS-240 X-Quad by altermac
...e 06/13/2016: added a raised version of the 15 degree cam-mount. you can use a diatone led-board (30x7mm, 12v) for a front-light.
thingiverse
free
Mini Tricopter: Another Tail and Battery-Cover by altermac
...he servo mounts a bit lower. added 10mm to the 6i-tail-arm to make room for 6" props. should work with the short front-arms.
thingiverse
free
sera Biotop LED Cube 130 XXL: Filtereinlass / filter intake by altermac
...r is designed for the filter inlet of a sera biotop cube 130 xxl led, but may fit to other, similarly structured internal filter.
thingiverse
free
CC3D Atom Nano / Micro Skyhunter mount by Zapf
...what a kludge! thanks for your hard work though altermac should work with ~16mm m3 screws, i'm using 18mm...