11 Towndrunk 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
![Magnetic Camera Mount by TownDrunk](/t/10240344.jpg)
Magnetic Camera Mount by TownDrunk
...ate 6/30/2021 created shorter versions (v2) with 5 magnet holes (3 on top, 2 on side) for base and rotated properly for printing.
thingiverse
free
![Mosfet Mount for JGMaker Artist-D by TownDrunk](/t/9675406.jpg)
Mosfet Mount for JGMaker Artist-D by TownDrunk
...0 board: aceirmc 2pcs 30a mos tube heat bed power module expansion board
50x60 board: heat bed mosfet, mactisical 2 pack - 25 amp
thingiverse
free
![Runout Sensor Mount for JG Maker Artist-D by TownDrunk](/t/10240346.jpg)
Runout Sensor Mount for JG Maker Artist-D by TownDrunk
...crew or drill a hole and use a m3 screw.
update 6/17/2021: uploaded tall versions of both mounts with more 15 mm more projection.
thingiverse
free
![Part cooling duct for BMG Aero mount (JGMaker Artist-D) by TownDrunk](/t/8339957.jpg)
Part cooling duct for BMG Aero mount (JGMaker Artist-D) by TownDrunk
...this fan has a bigger foot print.
print fan duct with supports with bottom flat side down. m3 hardware needed to attach to mount.
thingiverse
free
![LED Strip Mount for Artist-D Pro by TownDrunk](/t/10235166.jpg)
LED Strip Mount for Artist-D Pro by TownDrunk
...ut had to lengthen the wire by about 2 ft.
i tucked my wires under the blue plastic strip that houses the filament runout wiring.
thingiverse
free
![Case for Raspberry Pi 7" Screen by TownDrunk](/t/9238838.jpg)
Case for Raspberry Pi 7" Screen by TownDrunk
...0 blue led fan
raspberry pi touchscreen setup - instructables
raspberry pi documentation
install octoscreen
octoscreen setup help
thingiverse
free
![BMG Aero mount for JGMaker Artist-D by TownDrunk](/t/8356635.jpg)
BMG Aero mount for JGMaker Artist-D by TownDrunk
...er fan mounts with the proper offset to work with the mistral fan. also what i hope is the final version of the part cooling fan.
thingiverse
free
![myQ Chamberlain Smart Garage Door Opener - Sensor Mount by TownDrunk](/t/9689224.jpg)
myQ Chamberlain Smart Garage Door Opener - Sensor Mount by TownDrunk
... of the time.
links:
myq chamberlain smart garage door opener - wireless garage hub and sensor with wifi & bluetooth (amazon)
thingiverse
free
![Drag Chain mounts for JG Maker Artist-D by TownDrunk](/t/10236780.jpg)
Drag Chain mounts for JG Maker Artist-D by TownDrunk
...you decide to drill into your case.
bed mount: two #3x12mm screw, nut.
links:10x10 chain on amazon.
10x11 open chain on amazon.
thingiverse
free
![Y-Tensioner for JG Maker Artist-D by TownDrunk](/t/10238670.jpg)
Y-Tensioner for JG Maker Artist-D by TownDrunk
...
no knob: #5 x 20 (or 25) mm hex bolt, washer and nut, and #5 x 16 mm bolt & nut.
6mm belt on amazon 35 inches is generous.
thingiverse
free
![Fan duct for BMG Aero Wind/Bondtech BMG Mount (JGMaker Artist-D) by TownDrunk](/t/8506767.jpg)
Fan duct for BMG Aero Wind/Bondtech BMG Mount (JGMaker Artist-D) by TownDrunk
...ariations. z-coordinate will vary with bondtech, volcano, v6.
update 4/20/2021: added an experimental fan duct for opposite side.