53 Toddf 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Replicator Hood by ToddF
...replicator hood by toddf
thingiverse
this is a removable hood for the makerbot replicator.
thingiverse
free
Replicator front and side panels by ToddF
...replicator front and side panels by toddf
thingiverse
removable side and front panels for the makerbot replicator.
thingiverse
free
Zip Tie Organizer by ToddF
...ddf
thingiverse
an organizer for zip ties, pens, or what have you. 1.25" hex cells are 3", 4", and 5" deep.
thingiverse
free
Reinforced scupper plug by ToddF
...couple of the original scupper plugs broke. this is a refinement where the upper part of the plug is thickened up near the ears.
thingiverse
free
Sunshade for Lowrance Hook Reveal 7 by ToddF
...hook reveal 7 by toddf
thingiverse
a sun visor for a lowrance hook reveal 7.
as seen in this video: https://youtu.be/lqs3xf0dwzi
thingiverse
free
GoPro Session mount for GEPRC Mark4 HD5 frame by ToddF
...gopro session mount for geprc mark4 hd5 frame by toddf
thingiverse
hero 8 mount for the geprc mark4 hd5 frame.
thingiverse
free
Tetrahedral corners for straws by ToddF
...d with quadcopters, like the one shown. the stinger is used to pick up the tetras.
test video here: https://youtu.be/df9udwbfp4s
thingiverse
free
GoPro Hero 9 mount for Reptile Cloud 149hd frame by ToddF
...gopro hero 9 mount for reptile cloud 149hd frame by toddf
thingiverse
hero 9 mount for the reptile cloud 149hd frame.
thingiverse
free
GoPro Session mount for Reptile Cloud 149hd frame by ToddF
...e
gopro session mount for reptile cloud 149hd frame. versions with camera tilt angles 10 degrees up, level, and 5 degrees down.
thingiverse
free
Jaguar motor controller by ToddF
...jaguars to replace the real ones in some of our robots which are on display in the virginia air and space center, in hampton, va.
thingiverse
free
XT60 connector clamp by ToddF
...perfectly suited for use on other builds, though. it mounts the connector so you can plug and unplug your battery with one hand.
thingiverse
free
Rear looking GoPro Session mount for Reptile Cloud 149hd frame by ToddF
...e by toddf
thingiverse
rear looking gopro session mount for reptile cloud 149hd frame. versions with 5 and 10 degree down tilt.
thingiverse
free
Rekon 5 stock Vista antenna mount by ToddF
...pacers with a gps unit mount. i print it with the layers at a 45 degree angle to the antenna tube, for optimal bending strength.
thingiverse
free
4mm nut drivers and wrench by ToddF
...long driver can be held in your 8mm prop tool. a bit of heat shrink on one of your other hex drivers makes a handy storage spot.
thingiverse
free
"Mag" wheel for FRC robot by ToddF
... goes face down on the bed, and is grown using "full support". this keeps the upper lip of the rim properly supported.
thingiverse
free
GoPro 8 mount for GEPRC Mark4 HD5 frame (V2) by ToddF
.... similar to the v1 design, but with protection for all corners of the camera. includes files for 10 and 20 degree camera tilt.
thingiverse
free
Hex hole sizing plate by ToddF
...parts do not fit onto 1/2" hex shafting. i created this plate to allow the proper sizing of the hex holes in a solid model.
thingiverse
free
Rekon 5 FPV camera mount with XT30 clamp by ToddF
...i designed this camera mount for the caddx nebula pro to be similar to the included camera mount, but with the features i wanted.
thingiverse
free
Capacitor mount for GEPRC Mark4 HD5 frame by ToddF
...is a simple little part to allow the capacitor to be mounted to the bottom plate with a zip tie between the stack and the camera.
thingiverse
free
Reptile Cloud camera mount for 20mm reduced height standoffs by ToddF
...mount plates no longer fit. i replaced them with tpu parts that slide over the front standoffs and index in the top plate slots.
thingiverse
free
XT30 connector mount to Cloud 149hd frame by ToddF
...wire. m2 nuts are inserted in slots in one of the parts, and the two halves clamped in place with m2x12 screws. made from pla+.
thingiverse
free
Kodak Playsport belt clip by ToddF
...one handed removal from clip easier. this may necessitate covering up one of the top corners of the screen to preserve strength.
thingiverse
free
Waterproof bulkhead housing for Anderson Power Pole connectors by ToddF
...t and rubber washer from an off-the-shelf pg16 gland nut, if you have any extra.
installation video: https://youtu.be/ju1locfurhc
thingiverse
free
Reptile Cloud XT30 connector mount by ToddF
... needed to be mounted above the top plate. as in the previous design, this uses m2x12 screws and m2 nuts to clamp the connector.
thingiverse
free
Rekon 5 stock Vista antenna mount by ToddF
...spacers with a gps unit mount. i print it with the layers at a 45 degree angle to the antenna tube, for optimal bending strength.
thingiverse
free
FPV goggle battery rear strap mount by ToddF
...er balances the goggles both side to side and front to back. it also gives a nice "handle" to help put on the goggles.
thingiverse
free
camera mount for GoPro Hero 9 to GEPRC Mark4 HD5 frame (v2) by ToddF
...ers all 8 corners. includes files for a 20 degree camera tilt for fpv videos, and zero degree camera tilt, for cinematic videos.
thingiverse
free
camera mount for GoPro Hero 9 to GEPRC Mark4 HD5 frame by ToddF
...two flat head screws that thread into the front standoff with slightly longer screws. use washers to prevent tearout of the tpu.
thingiverse
free
Akaso V50x mount for Cloud 149hd frame by ToddF
...from pulling through in a crash. the back is secured with zip ties. this was printed laying on the flat side, with no supports.
thingiverse
free
GoPro 8 mount for GEPRC Mark4 HD5 frame (V1) by ToddF
...s is the v1 version, which is a close match to the hero 9 mount, and has a 10 degree tilt. there is another version coming soon.
thingiverse
free
Kodak Playsport belt clip ver 2 by ToddF
...camera loose with my index finger.
beefed up belt clip. the previous clip snapped off at the attachment point, during testing.
thingiverse
free
Spoked wheel for FRC robot by ToddF
...nd the spokes properly supported.
this wheel uses the same hub and rim as the "mag" wheel, from which it was derived.
thingiverse
free
Faired wheel for FRC robot by ToddF
...ners for mounting the tread. four small holes, visible in one of the pictures, show where the bosses are located.
weight: 95gm
thingiverse
free
Reptile Cloud 149hd tail for VTX, receiver, and antennas by ToddF
...w the instructions in the guide pages for assembling. other close up views can be seen in my other uploads from this same build.
thingiverse
free
Session 5 camera mount for Reptile Cloud frame by ToddF
...bit, so the retaining bumps on the sides could probably be reduced in size to more easily get the camera in and out of the mount.
thingiverse
free
Newport Vessels trolling motor tilt lock V2 by ToddF
... of the interior of the 3d print with 5 perimeters. i expect it to be more durable, but it needs on-the-water testing to be sure.
thingiverse
free
Reptile Cloud 149 duct for Gemfan 5 bladed prop, with ribs by ToddF
...light test video comparing flight times between these ducts and the stock reptile cloud 149hd ducts: https://youtu.be/k1fxbmoxsla
thingiverse
free
Reptile Cloud 149hd arm fairings by ToddF
..., and cover the motor wires. if you try them, post a comment about how they affect your quad's performance and battery life.
thingiverse
free
Rekon 5 All In One Flight Controller adapter (AIO) by ToddF
...ounting screws thread into the adapter. the 2mm screws will cut their own threads, but i suggest using a tap for the m3 threads.
thingiverse
free
DJI Air unit mount and antenna protector for GEPRC Mark4 HD5 frame, V2 by ToddF
...ending back by top plate.
base of antennas reinforced at breakage points.
zip tie holes added for optional prop guard attachment.
thingiverse
free
Reptile Cloud, Caddx Vista stock antenna mount by ToddF
... increase the length or add more spacers if using the stock 35mm standoffs. antenna mount printed from tpu and spacers are pla+.
thingiverse
free
DJI Air unit mount and antenna protector for GEPRC Mark4 HD5 frame by ToddF
...amp uses m2 nuts in slots on the tpu part, and clamps with m2x12mm screws. xt60 clamps printed with pla +. other parts are tpu.
thingiverse
free
GoPro Hero 9 mount for Reptile Cloud 149hd frame by ToddF
...mode button by mistake and couldn't see the screen. here's a flight (and crash) test video. https://youtu.be/qx64l3zyfie
thingiverse
free
90 degree waterproof bulkhead power pole connector housing by ToddF
...elp tighten the clamp nut. the housing is assembled with stainless hardware: m4 nuts and m4x14 stainless socket head cap screws.
thingiverse
free
GEPRC Mark4 HD5 prop guards by ToddF
...he left hand side. for right hand side parts, mirror them in your slicer software. print plugs laying on their sides, as shown.
thingiverse
free
Cloud Reptile ducts V2 improved durability by ToddF
...s.
there are two file versions, one with a tight fit on the gemfan 5 blade prop, and the other sized to fit the hq 8 bladed prop.
thingiverse
free
DJI Air unit mounts for GEPRC Mark4 HD5 by ToddF
... the antenna connectors. there are also lugs added for connecting the antenna protector/gps mount, which is uploaded separately.
thingiverse
free
regulated 2S 18650 battery pack for DJI goggles by ToddF
...vdc constant voltage. keeping the regulated voltage setpoint low (rather than 12 volts, say) makes the regulator more efficient.
thingiverse
free
DJI FPV goggle shims for temples and nose by ToddF
... wire bundling strips to the front and back of the temple shims. the nose shim is held in place with strips of narrow glue tape.
thingiverse
free
GEPRC Mark4 HD5 embedded arm protector by ToddF
...rinted with 25% gyroid style infill. the stock arms weigh 11 grams, and with the protectors the per arm weight goes to 15 grams.
thingiverse
free
Reptile Cloud 149 duct for Gemfan 5 bladed prop by ToddF
...tock ducts. plus, you can make them any color(s) you want.
credit to fpvcycle for the dimensions of the mounting hole pattern.
thingiverse
free
4s 18650 Battery Pack, square, zip tie, battery contacts by ToddF
... the nuts from backing out of their holes inside the pack. if the nut comes loose, you'll need to open up the pack to fix it.
thingiverse
free
4s 18650 Battery Pack, "flat" for pocket or belt, battery contacts by ToddF
...the nuts from backing out of their holes inside the pack. if the nut comes loose, you'll need to open up the pack to fix it.