31 Stmorgan 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Garden hose to 1/4NPT adapter by stmorgan
...garden hose to 1/4npt adapter by stmorgan
thingiverse
need to back flush the block on the tractor. this should do it.
thingiverse
free
Honda Keychain Solid Back by stmorgan
...chain solid back by stmorgan
thingiverse
wanted a bit sturdier keychain so i filled in the hollow version with a 2mm thick back.
thingiverse
free
Flat top cap for desiccant box by stmorgan
...a slick lid to make everything easier to print by flipping it over and having it flat on the glass, so i chopped the letters off.
thingiverse
free
Big Black Bowden Bulkhead by stmorgan
...nt to print the regular nuts with a raft. i ran into problems with the overhang where it began building threads close to the bed.
thingiverse
free
Height Micrometer by stmorgan
...001"? just move one notch, loosen bit and lightly push it up from the underside until it contacts micrometer. retighten jig.
thingiverse
free
Blade disposal box for Stanley single edge razors by stmorgan
... stanley single edge razors by stmorgan
thingiverse
just a little box to keep your dull blades from poking out of the trash bag.
thingiverse
free
E3DNonVolcanoMount-enlarged nut pockets by stmorgan
...this and the 3mm nuts slip in much easier. i've however since swapped to a microswiss because i didn't like losing the y.
thingiverse
free
CR-10 Carriage minus wheels - TinkerCAD friendly by stmorgan
...ke this more tinkercad friendly. just slabbed them off. threads and standoffs are still there, x and z dimensions still the same.
thingiverse
free
CR-10 Pen holder by stmorgan
...ear the reduced diameter where the cap snaps on and trimmed the outside edge so it doesn't hang over the original x carriage.
thingiverse
free
Pi Camera mount by stmorgan
...al old pla, print the top standing vertically with supports, resist the urge to lay it flat, the hooks will break at layer lines.
thingiverse
free
Modular Pi camera mount by stmorgan
...nt2 file is 30.4mm tall, designed to center the lens as close to 15mm up from the bottom as i could. this one is as yet untested.
thingiverse
free
Star PCB LED mount by stmorgan
...ectly. don't have the correct heatsink on hand yet, they're on the way. will test the clip and assembly when they arrive.
thingiverse
free
Pi3 Modular mounting plate by stmorgan
...t plate could leave room for the connectors. 3mm version is untested but confirm that 1.5mm version doesn't work with my pi2.
thingiverse
free
CR-10 Relocated Extruder V5 by stmorgan
...was lost off of the model while i was tinkering. also countersunk one of the screws that would get in the way of the tension arm.
thingiverse
free
Janky CR-10 Heatsink Mockup (Measurements from MicroSwiss All Metal) by stmorgan
...k.
1.75mm model is with 1.75mm filament modeled in place.
2mm model is with 2mm modeled in place, use for clearance for filament.
thingiverse
free
12° angle block for making a tangential toolholder by stmorgan
...compound angle for the tool bit slot.
plans can be found on www.gadgetbuilder.com on the "tangential toolholder" page.
thingiverse
free
CR-10S Fully integrated direct drive by stmorgan
... 12hr shifts at work coming up. buyer beware, things may not be lined up just right, i got it as close as i could eyeball though.
thingiverse
free
Straight line extruder and sensor by stmorgan
...and the extruder plate, it would have made it weak. updated and printed out v3 and it's fine. i'm calling it ready to go.
thingiverse
free
CR-10 Filament sensor 2020 mount by stmorgan
...ormal version is 80mm overall length, long version is 100mm.
"round" versions have had 2mm fillets added to most edges.
thingiverse
free
Pumpy the Younger by stmorgan
...
►found another microscopic gap in the foot_retained model. fixed and reupped. tinkercad must do some rounding off of dimensions.
thingiverse
free
Toolless PiPlate for RPi 2 or 3 by stmorgan
...ing on their side though, so the layer lines run in the unstressed axis. they're oriented correctly for printing in the stls.
thingiverse
free
CR-10 Relocated Extruder V4 with drag chain by stmorgan
...se mount to move it into alignment, it seems his top mount is meant to sit further in than what i have but it's hard to tell.
thingiverse
free
JD2 bender die model by stmorgan
...rinted dense enough to take the ramming. tradeoff being more metal to fill mold and more metal to cut away when finish machining.
thingiverse
free
Lost PLA Pipe Bender Dies by stmorgan
...right in the casting. holes will probably need reaming, radius may need sanding or machining.
uploaded followers with no sprues.
thingiverse
free
CR-10 Direct Drive - Sturdified by stmorgan
...7
3/24/18:
► added directdrive_horizontalstepper. has clearance for stepper wiring harness to exit the front and a zip tie lug.
thingiverse
free
5/8 diameter push in LED holder by stmorgan
...signal indicators which my tractor doesn't have. these will keep the little flying spawn of satan from filling them with mud.
thingiverse
free
PiSec Cam MKII by stmorgan
...f camera.
3-12: added trimring-fixed, trimring_sealed-fixed. shrunk diameter of shoulder to 100.5mm to ease assembly/disassembly.
thingiverse
free
Mount for 1893 bulb in 5/8" hole by stmorgan
... problem i had was it was prying itself open when trying to put into the hole, so i'm sticking with the single piece version.
thingiverse
free
PiSec MKIII - Compact Edition by stmorgan
... i made the holes 4.6mm with an 8mm large diameter on countersink. they should match most #8 or 4mm flat head screws well enough.
thingiverse
free
CR-10 Direct Drive extruder with integrated RSE-2 by stmorgan
...sure there's no other problems. looks good just looking at it. got some stringing and ugly places. used hatchbox white petg.
thingiverse
free
CR10S and CR10 Direct Drive - Sturdified with filament sensor and stock screws by Simtpal
...2800899. if you do find long enough conical screws to fit in stmorgan's sturdy direct drive, please use his, its more sturdy.