15 Racoon2020 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Bearing Extractor by Racoon2020
...bearing extractor by racoon2020
thingiverse
inner and outer bearing extractors for small bearings such as 608, 609.
thingiverse
free
TUSH - Thin Remix by Racoon2020
...tush - thin remix by racoon2020
thingiverse
use half less filament as the original.
thingiverse
free
PushDrill Clip-in EndCap by Racoon2020
...giverse
the endcap provided by lobocnc does not hold in place.
this one does, need some force+twist to insert but then stays in.
thingiverse
free
LACD Ultimate / Carabiner Protector by Racoon2020
...on2020
thingiverse
protection against wear for lacd via ferrata ultimate set. to install, open the carabiner and slide in place.
thingiverse
free
Volvo V40 Console Cable Holder by Racoon2020
...older by racoon2020
thingiverse
cable holder for volvo v40 for models 2012 and after. retain lock mecanism from central console.
thingiverse
free
ShengYang Charge Limiter Case by Racoon2020
...harge limiter https://fr.aliexpress.com/item/4000052577165.html?spm=a2g0s.9042311.0.0.7fc76c37flnmbs
requires 4x m3 hex nut 10mm.
thingiverse
free
Cell Spacer - 18650 by Racoon2020
...a 60 degrees version (to minimize overall strips length) but for space, cooling and simplicity, the linear pattern clearly rules.
thingiverse
free
Anycubic i3 Mega S - Extruder Filement Guide by Racoon2020
...se
replacement for the standard i3 mega s extruder filament guide.
use a 2mm drill bit to ensure filament guide hole is correct.
thingiverse
free
Another SC8UU Holder by Racoon2020
...hole size 15.35mm (this should give the strongest print)
vertical: hole size 15.1mm (alternative in case of issue with the above)
thingiverse
free
Windshield Ridex to PCB 19mm adaptor by Racoon2020
...e in the orientation provided, with support under the rear mobile part of the ptb and under the 2 little lugs of the ridex plate.
thingiverse
free
BBSHD Gasket Controller / Flat version by Racoon2020
... be correct. so i could have simply done an intersection operation instead of this redraw. anyway now it is done (and parametric)
thingiverse
free
TUSH - Thin Remix by Petr_B
...tush - thin remix by petr_b
thingiverse
remix of tush by racoon2020
added holes for m3 screws
thingiverse
free
Anycubic i3 Mega MK4 - Piezo Z probe carriage by Racoon2020
...close or below the 0.02 mark would be good enough.
i have attached a patch for marlin 2.0, modify it according to your mod/taste.
thingiverse
free
Anycubic Mega S Even Flow Circular Fan Duct by Racoon2020
... fan or equivalent 45mm radial fan duct located in original place.
the picture shows the vortex effect with water, really nice :)
thingiverse
free
Franke Soap Pump Shell by Racoon2020
...ed at step 8. stop once too is aligned with thread start of the shell.
reassemble pump as in the original part and give it a try.