16 Kiolia 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
2020 OpenBeam Cable Clip by Kiolia
...le clip for 2020 openbeam. there are probably many like it, but this one is mine. it has a slight relief carved out of one end.
thingiverse
free
Silica Container for Top Mount Dry Box by Kiolia
...t should work for spools up to 60mm internal diameter (or just don't stick it in a spool -- that'll work too, of course).
thingiverse
free
Clamp Bar for double 19mm cPAP Tubing by Kiolia
...erse.com/thing:2884959
you'll need zip ties to hold the clamps together.
includes 4 6mm holes for mounting or tying to stuff.
thingiverse
free
Universal Adjustable Belt Tensioner by Kiolia
... hand while pulling on the zip tie with the other.
sized for 6mm belts, but can easily be scaled as needed for other belt widths.
thingiverse
free
Kossel 2020 Corner Reinforcement by Kiolia
...e: https://www.thingiverse.com/thing:2941886
10/24/18 note: and spreader arms for that: https://www.thingiverse.com/thing:3173546
thingiverse
free
Articulated Filament Guide 2020 for Openbeam by Kiolia
... one more short over what's shown in the pictures to create a more evenly constrained arc through the 180 degrees down-to-up.
thingiverse
free
Bowden Tube Through-Wall Fitting For 12" Round Drybox by Kiolia
...ing. i also had to ream out the holes in the part a little to get a good fit on the tubing, but better too small than too large!
thingiverse
free
Wire Strain Relief for Anycubic Kossel XL Print Head by Kiolia
...be sure i had enough threads engaged since on the anycubic these screws are what hold the hotend into the overall head assembly.
thingiverse
free
Kossel Linear Lower Cover by Kobebrain
...kossel plus with tower reinforcemet easy to remove for corner reinforcement by kiolia (https://www.thingiverse.com/thing:2474583)
thingiverse
free
Retractor / Lift Spring Arms 15-40cm reach by Kiolia
...ook pretty neat compared to a piece of bungee. beefier versions would probably look hella rad as supports for a flying extruder.
thingiverse
free
Monster / Red Bull / Energy Drink Can Ice Bath Chiller by Kiolia
...t pretty much anything else. there's a conservative fill line inside so you don't overflow.
that's about it! enjoy!
thingiverse
free
Strain Relief for Anycubic Kossel Linear (Remix) by peaberry
...my extruder are spaced at 12mm x 22mm, and i measured the extruder diameter at 15.95mm.
thanks to kiolia for the original design!
thingiverse
free
Kiolia's Double Bowden-Cooled Lightweight Kossel Effector for Trick Laser 3/8" Barbells by Kiolia
...w also know that you can swap fan pins 7 and 9 to drive your part cooling off the fan_1 pins. if you're curious or whatever.
thingiverse
free
Kossel linear bearing carriage for Trick Laser 3/8" barbells by Kiolia
...barbells already, i designed a pretty rad (if a bit overspecialized) bowden-cooled one: https://www.thingiverse.com/thing:2884959
thingiverse
free
Centrifugal Compressor 120mm Case Fan Conversion by Kiolia
...x m3x6mm grub screws (cone point) if using impeller base
6x 1x5mm magnets if using impeller base
superglue if using impeller base
thingiverse
free
Kossel Wire Cable Frame Braces 2020 (Unlock WARP SPEED) by Kiolia
...s of tension.
10.24.18: spreader arms posted to help fix most of the volume loss issue: https://www.thingiverse.com/thing:3173546