29 Falkor 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Falkor Split by CalculatedChaos
...edchaos
thingiverse
this is a remix of mz4250's falkor model. i sliced it into 6 pegged pieces to allow for larger printing.
thingiverse
free
Falkor by mz4250
...n supporting my efforts making free models for the world to enjoy? check out my patreon page here: https://www.patreon.com/mz4250
thingiverse
free
Falkor full size cam wing mount
...m wing mount
thingiverse
one piece wing mount for a full sized foxeer falkor 1200 tv lines fpv cam
this is drawn in inch format.
thingiverse
free
Foxeer Falkor adaptor for Armattan Chameleon by RenoMemento
...e
the new foxeer falkor doesn't fit the armattan chameleon frame, so i designed this little adaptor ;)
happy fly my friends!
thingiverse
free
Foxeer Falkor Mount for Armattan Marmotte
...o be in a sufficiently advanced position to not show the edges of the cage in the lens but at the same time protected from shocks
thingiverse
free
FPV camera mount Foxeer falkor
...l only fit on the zmr 250 frame)
hope you like it ! if you have any recommendations on how to upgrade the piece, please tell me !
thingiverse
free
Zohd drift mount for Foxeer Falkor 2 Micro FPV Camera by J40YKE
...he existing foam mount, glue in this new mount. the camera should be an interference fit, but apply hot glue if needed to secure.
thingiverse
free
Martian Reptile to Foxeer Falkor II Camera Mount by Fargo1
...era mount-to-frame (tapped)holes are for m3 screws. camera mounting holes are for m2 screws.
filament: 1g
print time: 20 minutes
thingiverse
free
Funjet Ultra 2 FPV nose Predator / Falkor MINI
...ert and remove the lid a few times to losen it up so it does not bind with the camera stuck inside!!!https://youtu.be/dqtry_tukfw
thingiverse
free
RVJET nose for GoPro and FPV camera
...o 7 and foxeer falkor. it is detachable using magnets and mpx connectors. it can be printed in two parts and then glued together.
thingiverse
free
MFD Crosswind Mini Nose Cone for Falcor V2
...lydream crosswind mini nose cone for foxeer falcor v2 mini camera.
(http://foxeer.com/foxeer-falkor-2-camera-mini-standard-g-257)
thingiverse
free
HGLRC XJB-145 cam mount
...nd-offs , and the camera lens is protected better .it falls complete inside the tpu mount without having the tpu in the picture .
thingiverse
free
Spec Wing FPV Camera Mount by IcarusFPV
...so added a larger lens opening for the falkor full and mini cams. designed for the ritewing spec but should fit similar airfoils.
thingiverse
free
Foxeer focus ring by TheSwedishBear
...ise:
100% infillno support (support will ruin the threads)< 0.125 layer height (if higher the threads won't form properly)
thingiverse
free
Harrier S1100 Nose Camera Mounts Caddx Tarsier and Foxxeer Mini by boodadude
...era during a crash. i spun my plane in from about 100 feet and broke the whole nose off but my foxeer falkor was completely fine!
thingiverse
free
Ritewing Zcon / Recon DJI Osmo Action Nose
... lower hatch flush. top rear indent is to glue top hatch onto.
print the right way up, needs supports. i think i used 10% infill.
thingiverse
free
Nutmeg Pusher Whoop mod with Gopro Naked mount by M_Tops
...foxeer falkor
vtx : no name 200mw
rx : crossfire micro
tx : tbs tango 2
goggles : fatshark hdo
hd camera #1 : gopro 6 black naked
thingiverse
free
Nutmeg Pusher Whoop mod with Gopro Naked mount by M_Tops
...foxeer falkor
vtx : no name 200mw
rx : crossfire micro
tx : tbs tango 2
goggles : fatshark hdo
hd camera #1 : gopro 6 black naked
thingiverse
free
GWS Servo Mount & FPV Cam Holder
...oop on the back which you can feed your camera wire through, this will help keep it in position when rotating all the way around.
thingiverse
free
FPV nose pod for X-UAV Snow Goose (Mini Goose)
...
i included 2 versions , they are different in the way the antenna goes through the top of the pod, just choose the one you like.
thingiverse
free
Robust Flight Camera Pan Assembly for FPV Flying Wings by Gigahurtz
...t honestly, i'm not sure it needs it as it moves very smoothly after sanding down the surfaces and applying synthetic grease.
thingiverse
free
GoPro 5/6/7 Mini FPV camera holder, weighted
...e this a little heavier than a gopro (go pro 7 is 116g) if needed.
printed in tpu at 100% infill this model weighed 30.8g for me.
thingiverse
free
The Pushy Hawk (Emax Babyhawk r Evolution)
...ink/dkm3aiffgt
m2 screws
https://www.banggood.com/custlink/gdmdsi71he
foxeer falkor
https://www.banggood.com/custlink/3kkvsjk6mj
thingiverse
free
Canopy for Talon Pro (Mini Talon V2) by Herman_
...to m3 standoffs glued in the foam underneath.
i'm still tinkering with this design, the shape of the canopy is however final.
thingiverse
free
S600 Speed Demon Flying Wing
...e with no torque roll at all! this maiden was on 4s, just imagine it on 6s with better motor and esc!https://youtu.be/dyvgcbks_qk
grabcad
free
falkor
...falkor
grabcad
3d print
cg_trader
$15
Falkor Luck Dragon sitting inspired by Neverending Story | 3D
...y | 3d
cg trader
3d printable model falkor luck dragon sitting inspired 2 , available formats stl, ready for 3d animation and ot
cg_trader
$10
Sofa Falkor
...cgtrader.com/gallery/project/nordic-house
later i will convert the full project in an unreal scene to create an interactive file.
grabcad
free
Falkor 7" sub250 Ultralight Frame
...ra & whoop camera mounting
-compact whoop sized vtx
-7" biblades for endurance
-6" triblades for nimble fast flying