15 Comikzink 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Samsung Gear360 Dock (2016/2017) by ComikzInk
...em.
the 2016 side is setup so that it can sit on it's own or with a few mounts still attached below it like i have (see pics)
thingiverse
free
PlayStation / Xbox controller hybrid stand by ComikzInk
...ed.
only minor editing to the files by myself, most of the work in this was that of the two creators referenced and linked above.
thingiverse
free
Onewheel (Pint) Bearing Press Spacers by ComikzInk
...hub casing can crack the metal. you should only do this if you feel capable of pressing the bearing in straight with this method.
thingiverse
free
3 Bladed Prop Spinners by ComikzInk
...essary spacing in for the props however if you're unsure your prop will fit base 2 then try the base 1 will probably be best.
thingiverse
free
Flite Test Gremlin Battery Protector (skid plate) by ComikzInk
... as non-commercial as it includes the flitetest logo in which only they should have the right to sell work with their trademarks.
thingiverse
free
Onewheel Tyre Stand (With Alternative Versions) by ComikzInk
...
pinout for arduino
usb in provides 5v power.
arduino 5v -> led 5vin
arduino gnd -> led gnd
arduino pin 2 -> led data in
thingiverse
free
Onewheel Battery Capacity Display by ComikzInk
... lithium ion config) however for a v1 or plus you may need a different setting that matches your boards battery type and voltage.
thingiverse
free
DJI Mavic Pro 1 Angled Wall Mount by ComikzInk
....
i recommend using screws 70mm or longer with appropriate wall plugs. front to back of the screw hole is 50mm deep and 4mm wide.
thingiverse
free
FT Gremlin Carry Case (TJ Frame) by ComikzInk
...els unfortunately as i do not own them, feel free to remix the design if you do have it so others can enjoy the case :)
<3 lia
thingiverse
free
ImmersionRC Vortex 285 Angled Wall Mount by ComikzInk
...ble sided tape. simply place it where you want then drill into the wall through the pre-made hole in the mount and screw it down.
thingiverse
free
Losi Tenacity SCT GoPro Mount by ComikzInk
...camera) and tighten up the bolt into the nut on the other side. if it's loose try using insulation tape to layer up the slot.
thingiverse
free
Onewheel Battery Capacity Display With Light by ComikzInk
... lithium ion config) however for a v1 or plus you may need a different setting that matches your boards battery type and voltage.
thingiverse
free
Spektrum DX2E Screen 4.3" Mount by ComikzInk
...th a nice shade to keep the sun off it.
i've uploaded thesketchup file incase you wish to make any adjustments to the design.
thingiverse
free
FliteTest Swapable Spitfire Retractable Landing Gear by ComikzInk
... for your foam-board ft spitfire!
happy flying and enjoy, feel free to comment and share your experience with the gear.
lia <3
thingiverse
free
Onewheel Modular Battery Display Flight Fin Spacer (With Fuse, XT90 VnR Port & XT30 Accessory Port) by ComikzInk
...y display is showing by switching modes.
again, but in percent mode.
you're done. congrats you didn't nuke your board!