20 3dmaka 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Camera Lens Cap Flexible TPU by 3DMaka
...camera cap flexible tpu
sized for action cam, see: https://www.thingiverse.com/thing:2457578
or
lens dia. of 22.60 mm / .5 mm +/-
thingiverse
free
Hammer Hold / Holder by 3DMaka
...is sized for about a 1" + (28mm) round hammer head.
haven't had a chance to print it yet. let me know if you make one..
thingiverse
free
Drone RC Antenna Spread by 3DMaka
...ds to mount the antennas pointing 90 degrees from one another so that one of them is always receiving a signal at any given time.
thingiverse
free
Ice Cube Maker / Chiller For Thermos by 3DMaka
...large ice cubes. freeze.. than thaw in warm water..pop 2 in
haven't printed this yet.. let me know how it works out... thanks
thingiverse
free
Anet A8 Bed Spring Booties by 3DMaka
...s) help keeps springs straight.. and in the end run.. maybe of no real benefit..
print 2 per spring, sized for anet 8 builds 2017
thingiverse
free
Tasco Rifle Scope Cap by 3DMaka
...oosely...measured 0.40mm difference between front and rear.
can be used for rear end.. just adjust "slicer" percentage
thingiverse
free
Motor Wire Clamp / Harness / Anchor Anet A8 X Motor by 3DMaka
...ires would break.
nice snug fit.. est about 1lb of holding force.. depending on printer... adjust slice scaling as needed for fit
thingiverse
free
Lithium Grease Spray tube holder / Keeper by 3DMaka
... temp to 205c half way thru / fan on
use double sided tape to secure to can / wipe can and " thing" with alcohol prior.
thingiverse
free
Anet A8 Z Hieght / Stop Micro Switch Adjustment by 3DMaka
..... this can be printed to set the height needed for setting z height.. when slicing set z height as applicable (leave x,y as is)
thingiverse
free
Eachine Propeller Guard / Drone E58 / Little Mavic by 3DMaka
...ut more weight.
for more info on the white colored connector for the propeller ... see:https://www.thingiverse.com/thing:2797871
thingiverse
free
Tubing Bender Tight Radius / Brake Line by 3DMaka
...ed in pla / no supports / flat on table.
since i'm not much on building puzzles... some hints...vise grips, board, stop block
thingiverse
free
Drone Brushless Motor Wrench / Gripper by 3DMaka
...ssure. torque of over tightening the nut of the propeller... can / could crack propeller...u get a feel for these king of things
thingiverse
free
Action Cam Case / Housing / Protection / Flexible TPU by 3DMaka
...icult to remove, due to retaining lip, will offer an alternative in near or distant future. bear this in mind before printing.
ya
thingiverse
free
Eachine E58 Propeller Repair Part by 3DMaka
... to clean up.. and is has lasted more abuse than the original.
for propeller guards see:https://www.thingiverse.com/thing:2805529
thingiverse
free
Anet A8 X Belt Anchor / Clamp / Holder by 3DMaka
...ot bolted) pull motor back in place.. bolt it up...bolt up x belt anchor
2nd image see: https://www.thingiverse.com/thing:2443990
thingiverse
free
Anet 8 Bearing Block For 8mm Composite Bearing Bushing Sleeve by 3DMaka
..... to guide drill / reamer center if used
search "thebay".... found a 10 pack of 8x10x15mm bearings for around 5 bucks.
thingiverse
free
USB Cable Holster / Holder / Or Cheap Table Lamps..Take your pick by 3DMaka
...ld long
the lighted usb cable is dirt cheap find them at the dollar store... handles data and power..and so far is still working.
thingiverse
free
Anet A8 X Duo Bearing Block 8mm Composite Bearing Bushing Sleeve by 3DMaka
...tance position with each other..or... have you ever noticed the the drive screw drive shaft not centering in the top mount plate?
thingiverse
free
X-Carriage by olek
...a8 x belt anchor / clamp / holder by 3dmaka ...
thingiverse
free
Eachine E 58 Propeller Guard by Cees_Meijer
...by cees_meijer thingiverse based on the propeller guard by 3dmaka i designed this version which covers a wider area...