Thingiverse
![ZumPiZeroW by kc9rqi](/previews/8645060.jpg)
ZumPiZeroW by kc9rqi
by Thingiverse
Last crawled date: 3 years, 1 month ago
Here is a case for the ZumSpot. There are no screws needed for this case. There are two options for the lid, One is if you are using a Nextion screen and need access to the jumpers, the other is if you are using a small 0.96" LCD display. The lid is tight so you may need to "scrape" the sides down some depending on your print quality.
Similar models
thingiverse
free
![FLIRC case lid for OLED Display](/t/4871752.jpg)
FLIRC case lid for OLED Display
...ere are two parts, the lid and a small piece to hold the display in place. to mount the pieces on the flirc case you need screws.
thingiverse
free
![Adjustable Base Case](/t/4908624.jpg)
Adjustable Base Case
...ommented in code)
after printing your case, press m3 nuts into the hex-holes of the lid and use m3 screws to connect box and lid.
thingiverse
free
![18650 case with magnet](/t/4803470.jpg)
18650 case with magnet
...lid. note: you may need to file /sand the edge the lid slides over for a snug fit!! * not all printers print the same tolerance.
thingiverse
free
![Groz 4" Engineering Square Case with Lid by elliotboney](/t/8714205.jpg)
Groz 4" Engineering Square Case with Lid by elliotboney
...elliotboney
thingiverse
needed a case for my groz 4" engineering square cause the box it came it was getting old and nasty.
thingiverse
free
![Orange Pi Zero 2 Case by Sephiroth1337](/t/8341349.jpg)
Orange Pi Zero 2 Case by Sephiroth1337
... with a camera module.
update:
added corners for mounting the lid with m3 screws.
you can use threaded inserts to fasten the lid.
thingiverse
free
![Cafe Cup lid by samcai098](/t/8703827.jpg)
Cafe Cup lid by samcai098
...thingiverse
this is a "cafesito" cup lid, cafe lid. you can use this if you want to save your cup and keep reusing it.
thingiverse
free
![Pot lid knob (Print-in-place nut) by Akiland](/t/8732955.jpg)
Pot lid knob (Print-in-place nut) by Akiland
...place" nut.
this means that you have a real nut inside of your print to use with a real screw.
use an m4 nut
no glue needed.
thingiverse
free
![PI-4 with SSD case by afleak](/t/8130861.jpg)
PI-4 with SSD case by afleak
...rent usb and ethernet port configuration of the 3.
if you print the box in a vertical orientation, support structures are needed.
thingiverse
free
![Raspberry Pi Zero Case by XYZMurf](/t/8881636.jpg)
Raspberry Pi Zero Case by XYZMurf
... waste it. :)
please comment on this "thing" i would love to here if you guys like it, and if you have any suggestions.
thingiverse
free
![Powersupply Cover by Modellaner](/t/8270561.jpg)
Powersupply Cover by Modellaner
...
some strong super glue or maybe "acrifix" (to stick the halfs together)
some colours (to paint the sign on the lid)
Kc9Rqi
thingiverse
free
![DvMega_Pi by kc9rqi](/t/8653985.jpg)
DvMega_Pi by kc9rqi
...dvmega_pi by kc9rqi
thingiverse
dvmega case for raspberry including cut out for display. cost was about $6.00 in pla. 2
thingiverse
free
![Scion tC Cargo Peg by kc9rqi](/t/8774431.jpg)
Scion tC Cargo Peg by kc9rqi
...scion tc cargo peg by kc9rqi
thingiverse
2015 scion tc cargo cover peg.
thingiverse
free
![NooElec Balun cover by kc9rqi](/t/8740507.jpg)
NooElec Balun cover by kc9rqi
...ld the nooelec antenna balun 1:9 hf balun to protect it.
https://www.amazon.com/nooelec-balun-one-nine-applications/dp/b00r09wht6