Thingiverse
ZMR250 Hybrid by shawdreamer
by Thingiverse
Last crawled date: 3 years ago
aye odd title for design I know but bare with me and you'll start to understand.
This design is more of a set of designs, the designed parts contained within can be used in Multiple configurations and can incorporate the use of stock ZMR 250 frame parts if the builder so wishes (or not if they choose, its entirely down to their own tastes, desires or needs.
included designs are
alternative full 3d printed ZMR arms (with Esc cavity and built in LED's)
lower sandwich plate spacer with rear led board mount(for stock 3mm ZMR arms)
upper plate (battery slot, alarm/vtx mount, protective shroud for cam antenna)
lower plate with skid feet.
the designs are made in such a way as to match the dimensions and hole layout of stock ZMR 250 frame plates so the builder can use the stock plates for additional strength (I currently fly the FULL 3d printed version of this design and find it remarkably strong tbh but the choice is yours), this also allows for the optional use of the upgraded PDB type ZMR plates too.
Though I have dispensed with the use of the upper stock plate in my own builds (giving the whole frame a more low slung streamline appearance) the plate is still usable if you wish (though imho the whole thing will look top heavy if used with the spacer parts)
The cam Ill be using and the parts are designed around is a Eachine AIO tx03 but they should work fine with sinilar AIO types (including the tx02 and 01 obviously), however if the builder chooses to use one of the stock ZMR plates a slot must be cut into it to allow for the antenna.
well I could sit here explaining all the different variants you could use but you can probably figure the rest out for yourselves.
the built version Im using as is shown above in the pictures is as I said the entire 3d printed version without using zmr stock parts, its entirely ABS and very tough and rigid.
to minimise height requirement of the spacer I designed it primarily around the use of a CC3d v2.0 which had a built in PDB with 12v & 5v regs (it can also be directly powered from anything upto 6s lipo in cell amount), however you can fit any 30x30 FC (Naze, f4 etc) inside with upto a 30x30 PDB even with your receiver and cam still in there, you just have to be more careful with your wire management.
Ive shoved in a pic of a handful of possible variants above to give some general ideas of what possible, enjoy and feel free to comment or suggest further mods.
ooops forgot to mention...
the leds I designed for and will be using are these:-http://www.ebay.co.uk/itm/142067571176?_trksid=p2057872.m2749.l2649&var=441163776462&ssPageName=STRK%3AMEBIDX%3AIT
22/4/2017:-added
stock arm esc covers
snapshots of build variants
24/4/2017:-added
LED mounts for 5mm leds (alternative to using neopixel smd leds)
for ease of install Id recommend "pre-wired" LEDs, Ive used the following seller for multiple projects and his pre-wired LEDS are reliable, REALLY "ultra-bright" at 12v but still bright at 5v (without needing to change the resistor pre-installed).
they have many varying colours and function pre-wired 5mm leds that are usable (such as flashing & flicker) aswell as flat-top version LED's
http://www.ebay.co.uk/itm/5-x-Pre-Wired-White-LED-5mm-Ultra-Bright-9V-12V-1st-CLASS-POST-/301164692846?hash=item461ed0856e
http://www.ebay.co.uk/itm/5-x-Pre-Wired-Red-LED-5mm-Ultra-Bright-9V-12V-1st-CLASS-POST-/301164692609?hash=item461ed08481
This design is more of a set of designs, the designed parts contained within can be used in Multiple configurations and can incorporate the use of stock ZMR 250 frame parts if the builder so wishes (or not if they choose, its entirely down to their own tastes, desires or needs.
included designs are
alternative full 3d printed ZMR arms (with Esc cavity and built in LED's)
lower sandwich plate spacer with rear led board mount(for stock 3mm ZMR arms)
upper plate (battery slot, alarm/vtx mount, protective shroud for cam antenna)
lower plate with skid feet.
the designs are made in such a way as to match the dimensions and hole layout of stock ZMR 250 frame plates so the builder can use the stock plates for additional strength (I currently fly the FULL 3d printed version of this design and find it remarkably strong tbh but the choice is yours), this also allows for the optional use of the upgraded PDB type ZMR plates too.
Though I have dispensed with the use of the upper stock plate in my own builds (giving the whole frame a more low slung streamline appearance) the plate is still usable if you wish (though imho the whole thing will look top heavy if used with the spacer parts)
The cam Ill be using and the parts are designed around is a Eachine AIO tx03 but they should work fine with sinilar AIO types (including the tx02 and 01 obviously), however if the builder chooses to use one of the stock ZMR plates a slot must be cut into it to allow for the antenna.
well I could sit here explaining all the different variants you could use but you can probably figure the rest out for yourselves.
the built version Im using as is shown above in the pictures is as I said the entire 3d printed version without using zmr stock parts, its entirely ABS and very tough and rigid.
to minimise height requirement of the spacer I designed it primarily around the use of a CC3d v2.0 which had a built in PDB with 12v & 5v regs (it can also be directly powered from anything upto 6s lipo in cell amount), however you can fit any 30x30 FC (Naze, f4 etc) inside with upto a 30x30 PDB even with your receiver and cam still in there, you just have to be more careful with your wire management.
Ive shoved in a pic of a handful of possible variants above to give some general ideas of what possible, enjoy and feel free to comment or suggest further mods.
ooops forgot to mention...
the leds I designed for and will be using are these:-http://www.ebay.co.uk/itm/142067571176?_trksid=p2057872.m2749.l2649&var=441163776462&ssPageName=STRK%3AMEBIDX%3AIT
22/4/2017:-added
stock arm esc covers
snapshots of build variants
24/4/2017:-added
LED mounts for 5mm leds (alternative to using neopixel smd leds)
for ease of install Id recommend "pre-wired" LEDs, Ive used the following seller for multiple projects and his pre-wired LEDS are reliable, REALLY "ultra-bright" at 12v but still bright at 5v (without needing to change the resistor pre-installed).
they have many varying colours and function pre-wired 5mm leds that are usable (such as flashing & flicker) aswell as flat-top version LED's
http://www.ebay.co.uk/itm/5-x-Pre-Wired-White-LED-5mm-Ultra-Bright-9V-12V-1st-CLASS-POST-/301164692846?hash=item461ed0856e
http://www.ebay.co.uk/itm/5-x-Pre-Wired-Red-LED-5mm-Ultra-Bright-9V-12V-1st-CLASS-POST-/301164692609?hash=item461ed08481
Similar models
thingiverse
free
ZMR 250 frame add-ons by shawdreamer
...tx02 and tx01 aio's also, these dimensions are also similar to other brands of aio cams but please check...
thingiverse
free
ZMR front/back 5mm spacer by adrozdetski
... for arms and 1mm for nylon spacer, but the openscad file has the lightspacer module with adjustable height for anyone to modify.
thingiverse
free
zmr 250 bottom plate spacers / led mounts (13mm) by aoello
...thingiverse
zmr 250 bottom plate spacers front/back (13mm). use with 1mm pillars on 3mm arms. holes for led wires and xt60 plug.
thingiverse
free
Realacc X210 Lumenier QAV210 LED Mount by AIRBOZ
...?var=&hash=item2a45f38b79:m:mkiv1hg_99plxrkej6borjw
designed to fit the realacc x210 but should also fit the lumenier qav210.
thingiverse
free
EMAX 250 Cleanhawk PDB Spacer by valade
...ect some symmetry problems.
i added the lower spacer beetween the pdb and the lower carbon frame plate.
screws used :
8 x m3x20mm
thingiverse
free
led housing for Eagle eye rear red LED and clip front white by beetbocks75
...w-eagle-eye-led-back-up-drl-daytime-running-radar-reverse-light-white-12v-uk-/400915319012?hash=item5d586a48e4:g:82uaaoswbllvsyor
thingiverse
free
LED Lamp by sir_veloso
...ne-on-off-button-table-lamp-desk-light-cord-cable-switch-new-/282362997625?var=&hash=item41be256b79:m:mqtyuyiruhdqjzcjem4qn5g
thingiverse
free
Mounts for DC 12v 360W PSU Under Base Board by TheBobGeezer
...base board and not occupy space, this is a similar ...
thingiverse
free
Desktop Synergy - Fingerprint+Power+SD+USB by DROUGA
...r=&hash=item2cadcb4b86:m:mwp5ul8mimdc0rwrpebeixq
tools:
soldering iron
desoldering pump
hot glue gun
wire cutters
crimp tool
thingiverse
free
12v 21 LED array by ColdWarPatriot
... in the picture, it is wired with ir leds. i used three 82 ohm resistors for the ir leds. wiring diagram included is for ir leds.
Shawdreamer
thingiverse
free
printbed standoff feet by shawdreamer
...printbed standoff feet by shawdreamer
thingiverse
standoffs
thingiverse
free
spool holder (horizontal) by shawdreamer
...spool holder (horizontal) by shawdreamer
thingiverse
spool holder
thingiverse
free
6x3 bullnose prop by shawdreamer
...6x3 bullnose prop by shawdreamer
thingiverse
material - pla
thingiverse
free
standalone heatbed feet by shawdreamer
...standalone heatbed feet by shawdreamer
thingiverse
feet for mk2a/b heatbed
thingiverse
free
Yamato-Class Benchy by shawdreamer
...yamato-class benchy by shawdreamer
thingiverse
benchy got a buff-up
thingiverse
free
U-boat Benchy by shawdreamer
...u-boat benchy by shawdreamer
thingiverse
last in the series of benchy spin-offs.
thingiverse
free
H-copter Canopy by shawdreamer
...h-copter canopy by shawdreamer
thingiverse
lightweight protective canopy for h-copter design
thingiverse
free
Nimitz-class Benchy by shawdreamer
...nimitz-class benchy by shawdreamer
thingiverse
whats better than a battleship benchy?
a aircraft carrier benchy!!
thingiverse
free
thermostatic controller board enclosure (large) by shawdreamer
...thermostatic controller board enclosure (large) by shawdreamer
thingiverse
enclosure
thingiverse
free
printrite z-stop repair by shawdreamer
...printrite z-stop repair by shawdreamer
thingiverse
simple glue on z-stop repair for stated printer
Zmr250
thingiverse
free
ZMR250 Parts by thunderbird18j
...zmr250 parts by thunderbird18j
thingiverse
zmr250 parts
thingiverse
free
ZMR250 Sidepanel by sitoca
...zmr250 sidepanel by sitoca
thingiverse
zmr250 sidepanel
thingiverse
free
ZMR250 Motorguards by sitoca
...zmr250 motorguards by sitoca
thingiverse
zmr250 motorguards
thingiverse
free
Motorguards for ZMR250 by Dimon372
...motorguards for zmr250 by dimon372
thingiverse
motorguards for zmr250
thingiverse
free
ZMR250 Feet by pupuyang
...zmr250 feet by pupuyang
thingiverse
zmr250 feet
thingiverse
free
Unispacer ZMR250 by darioc
...unispacer zmr250 by darioc
thingiverse
unispacer for zmr250 20mm
thingiverse
free
ZMR250 Spacer by meban
...zmr250 spacer by meban
thingiverse
zmr250 spacer (10 mm)
thingiverse
free
ZMR250 Stand by FPVpolska
...zmr250 stand by fpvpolska
thingiverse
this is the stand for zmr250 frame drone. enjoy :)
thingiverse
free
ZMR250 Backplate by robinmglsk
...zmr250 backplate by robinmglsk
thingiverse
zmr250 backplate, for mounting frsky d4r-ii and vtx
thingiverse
free
ZMR250 Part by BluefishNZ
...zmr250 part by bluefishnz
thingiverse
these are additional parts that can be used on a custom zmr250 quadcopter build.
Hybrid
3d_export
$10
hybrid watch
...hybrid watch
3dexport
turbosquid
$5
Hybrid Scope
...ree 3d model hybrid scope for download as blend, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1533651)
turbosquid
$39
Robot Hybrid
... 3d model robot hybrid for download as max, obj, fbx, and dae on turbosquid: 3d models for games, architecture, videos. (1373779)
turbosquid
$199
Hybrid Car
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
archive3d
free
Hybrid 3D Model
...id 3d model
archive3d
aircraft
hybrid 6 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$25
Honda insight hybrid 3D Model
...t hybrid 3d model
3dexport
honda insight-hybrid car vehicle insight hybrid
honda insight hybrid 3d model artline3d 26442 3dexport
3d_export
$45
Hybrid ce456 3D Model
...hybrid ce456 3d model
3dexport
alien robot 3d hybrid terminator code red flying camera
hybrid ce456 3d model dan3d 84278 3dexport
3ddd
$1
Hybrid Task Floor Light
...ight up your room in style with this contemporary hybrid task floor lamp, a great accessory for adding a fresh touch to the home.
turbosquid
$6
Hybrid drone car
...
royalty free 3d model hybrid drone car for download as blend on turbosquid: 3d models for games, architecture, videos. (1602619)
turbosquid
$5
AK12 with hybrid sight
...alty free 3d model ak12 with hybrid sight for download as skp on turbosquid: 3d models for games, architecture, videos. (1261141)