WLED ESP32 by Ulmerspatz

... remixed the bottom to be a little higher and to have cutouts so the soldered wires on my esp32 running wled fit nicely into it..

...ons - 1a power supply and usb connector parts: ws2812b rgb led strip button - 12mm tactile switch with cap esp32 1000uf capacitor

...d by aircoookie: https://github.com/aircoookie/wled connect the data pin of led strip to gpio2 and the button to ground and gpio0

...se thingiverse wled box for nodemcu to use with wled firmware to control ws2812b rgb ledshttps://github.com/aircoookie/wled/wiki

...wled box grabcad wled project box

...universal wled shield v3.0 grabcad universal wled shield v3.0

...universal wled shield v2.1 grabcad universal wled shield v2.1

...room for wires. removed button holes and dev board supports/. to fit a esp32 d1 board aitrip d1 using wled to control the leds.

...wled wemos shield box v1.0 by serg74 thingiverse wemos shield box for wled project

...wled nodemcu box by fabiolol thingiverse simple box to install nodemcu to control my ledstrips with amazing wled software.

...2 & ethernet by ulmerspatz thingiverse gehäuse für arduino r3 & ethernet shield und atlas t2 mk2 beta, noch nicht fertig

...;--> hörmann uap1https://github.com/ulmer-spatz/loxone/blob/main/garage.ino remix vonhttps://www.thingiverse.com/thing:4730585

...se thingiverse wled box for nodemcu to use with wled firmware to control ws2812b rgb ledshttps://github.com/aircoookie/wled/wiki

...wled nodemcu box by fabiolol thingiverse simple box to install nodemcu to control my ledstrips with amazing wled software.

...wled wemos shield box v1.0 by serg74 thingiverse wemos shield box for wled project

...wled shield box v1.5 by serg74 thingiverse wled shield box v1.5. ir glass part have to printed from transparent material.

...led strip with button (on/off or change mode) hardware: esp-01s (with 1mb spi flash) firmware: https://github.com/aircoookie/wled

... board (firmware for board is wled - https://github.com/aircoookie/wled) addressable led strip (ws2812b 60leds/m), width - 10mm

...d by dapostol73 thingiverse quick little box i build for housing my wled esp8266 board behind my tv for my hyperion project leds

...812 36cm stripe wled thingiverse a shortened version of the lamp. had a 36cm stripe laying around. recommending aircookies wled

...wled shield box v1.5 with display by blazoncek thingiverse

...esp32 cam with usb thingiverse esp32 cam with micro usb

...esp32 cam housing thingiverse housing for esp32 cam modul (tinker board)

.../de.aliexpress.com/item/lolin-esp32-oled-wemos-for-arduino-esp32-oled-wifi-modules-bluetooth-dual-esp-32-esp-32s/32807531243.html

...esp32 nodemcu case thingiverse a remix scaled up a bit to fit an esp32 nodemcu

...n be used to contain the esp32s chip. it has enough space to fit any header connectors and two holes to drive the cables through.

...esp32 copter remote thingiverse case for esp32 remote control: https://github.com/cody82/libcopter

...esp32 box by nordman thingiverse a box to fit a esp32 manualhttps://www.instructables.com/rally-controller-with-bluetooth/

...zable box https://www.thingiverse.com/thing:4607690 the esp32 came with pines already soldered so the box is big enough for that

... for a bluetooth tracker for me home automation. the wemos esp32 below is the one that i am using for this design. wemos esp32.

...esp32-cam holder by cockroach_dude thingiverse holder for esp32-cam