Thingiverse
Wing Joiner for X-UAV Talon by epquilloy
by Thingiverse
Last crawled date: 3 years, 2 months ago
I recently changed my wing servo connectors to rs232 DB9 connectors to facilitate quick setup/dismantle of my talon especially when doing mapping flights. But of course, to add extra support for the DB9, I then decided to add install wing joiners, not just relying on the wing clamps. The wing joiners are held by either steel M3 nuts and steel screws, but I opted to use nylon standoffs just like the ones used in Aeromapper Talon (I patterned my Talon on the Aeromapper Talon, but I am still waiting for the wing extensions). The wing joiners on the Aeromapper Talon are designed for setups with wing extensions, mine, however is for Talons WITHOUT the wing extensions, yet. I will modify the design as soon as the wing extensions arrive. The design of this wing joiner is a remix of the bolt on wing joiner for mini drak, by the way.
Aeromapper Talon:http://www.aeromao.com/aeromapper_talon_uav
X-UAV Talon DB9 connectors by Closus:https://www.thingiverse.com/thing:2786209
With nylon standoffs both on the V-tails and the wings, no special tools like hex keys are required for the assembly of my Talon. Just pop in the wings and lock them.
Instructions:
Print on ABS or PLA. Each wing joiner will require you to print two (2) joiner plates and one (1) wing joiner. On the Talon, I printed four (4) sets. After printing, you might need trim the joiner a bit to fit the joiner plates. To install, properly align the wings and the fuselage.Connect the wings into the fuselage with the spars installed. Mark the areas to be cut out. Use sharp blade to trim the foam. Make sure that the wing joiner is flushed such that will not be protruding on the foam, but dont over cut the foam so as not to make the joiner recessed. Do not forget to add nuts or standoffs underneath the joiner plates (hold the nut/stand off with CA glue). Apply foam safe glue on the wing and fuselage as well as on the side of the joiner plate to be bonded. Make final alignment prior to pressing the parts together.
Aeromapper Talon:http://www.aeromao.com/aeromapper_talon_uav
X-UAV Talon DB9 connectors by Closus:https://www.thingiverse.com/thing:2786209
With nylon standoffs both on the V-tails and the wings, no special tools like hex keys are required for the assembly of my Talon. Just pop in the wings and lock them.
Instructions:
Print on ABS or PLA. Each wing joiner will require you to print two (2) joiner plates and one (1) wing joiner. On the Talon, I printed four (4) sets. After printing, you might need trim the joiner a bit to fit the joiner plates. To install, properly align the wings and the fuselage.Connect the wings into the fuselage with the spars installed. Mark the areas to be cut out. Use sharp blade to trim the foam. Make sure that the wing joiner is flushed such that will not be protruding on the foam, but dont over cut the foam so as not to make the joiner recessed. Do not forget to add nuts or standoffs underneath the joiner plates (hold the nut/stand off with CA glue). Apply foam safe glue on the wing and fuselage as well as on the side of the joiner plate to be bonded. Make final alignment prior to pressing the parts together.
Similar models
thingiverse
free
X-UAV Talon DB9/D-Sub Plug Holder by Closus
...pictures)
i used uhu por to glue the holder into the wing
make sure the plug holders aren't recessed too deep into the wings!
thingiverse
free
X-UAV Talon MPX Plug Holder by Closus
...glue first
while drying, use clear tape (see picture 1) to hold the plug in place
i used uhu por to glue the holder into the wing
thingiverse
free
X-UAV Talon front skid by epquilloy
...t on its side lying on the print bed. you may use abs or pla. to install, just apply foam safe glue on the surfaces to be bonded.
thingiverse
free
X-UAV Talon Wing Holder by Closus
...uite well.
you can add two of these per wing to be sure it holds well.
if aeromao wants me to take this design down, let me know.
thingiverse
free
Aeronaut Triple - MPX Connector conversion kit
...e carefull not to glue the wing to the fuselage.
print in the orientation the stl loads and use supports for the mounting flange.
thingiverse
free
X-UAV Talon front skid V2 by epquilloy
...install, just apply foam safe glue on the surfaces to be bonded.
v1 front landing skid :https://www.thingiverse.com/thing:2723004
thingiverse
free
Sport cub wing joiner by dooeydon
... apply allen wrench to m3 bolt head and begin tightening. when the m3 bolts are secure on the m3 nuts, the wing will be secure.
thingiverse
free
Wing spar support for Talon Pro mini talon by epquilloy
...ment from the wing spar by having more surface are in contact. apply glue to mount to the fuselage.
note: print 2 pieces of this.
thingiverse
free
db9 connector ext joiner com port
...db9 connector ext joiner com port
thingiverse
db 9 com port extension with cover
thingiverse
free
Canopy for Talon Pro (Mini Talon V2) by Herman_
...to m3 standoffs glued in the foam underneath.
i'm still tinkering with this design, the shape of the canopy is however final.
Epquilloy
thingiverse
free
Battery tray for Talon Pro by epquilloy
...a but lighter and shorter. mount it with foam safe glue to the fuselage. dont forget to slide in the battery strap before gluing.
thingiverse
free
MPX 6 connector housing by epquilloy
...lane to install this. use foam safe glue like uhu por or e6000 to mount the housing into the foam plane. print two sets of these.
thingiverse
free
X-UAV Talon front skid by epquilloy
...t on its side lying on the print bed. you may use abs or pla. to install, just apply foam safe glue on the surfaces to be bonded.
thingiverse
free
X-UAV Talon Motor Mount by epquilloy
...nuts with <5mm outer hex edge to edge. note: if you are unsure about the nut you are using, just get the first design. cheers!
thingiverse
free
Wing spar support for Talon Pro mini talon by epquilloy
...ment from the wing spar by having more surface are in contact. apply glue to mount to the fuselage.
note: print 2 pieces of this.
thingiverse
free
X-UAV Talon flight controller deck by epquilloy
...ure the tray. zip ties can also be used as alternative to screws.
print instructions:
print the clip/holder 2x, print the tray 1x
thingiverse
free
MG90D servo adapter for TBS Caipirinha II by epquilloy
...in the comments section if you need one
update:
v1.1 adjusted the servo to give more clearance for the push rods (march 12, 2018)
thingiverse
free
X-UAV Talon front skid V2 by epquilloy
...install, just apply foam safe glue on the surfaces to be bonded.
v1 front landing skid :https://www.thingiverse.com/thing:2723004
thingiverse
free
emax ES08ma II servo adapter for TBS Caipirinha II by epquilloy
...r emax es08ma ii, it may not fit other servos. you may post your requests for your servos in the comments section if you need one
thingiverse
free
Front skid plate for Talon Pro or Mini Talon V2 by epquilloy
...ly foam-safe glue on the skid and mount it on the belly. secure the skid with tape while waiting for the glue to bond completely.
Joiner
turbosquid
$5
Joiners mallet
...el joiners mallet for download as 3ds, obj, fbx, 3dm, and skp on turbosquid: 3d models for games, architecture, videos. (1417675)
turbosquid
$2
Electric Joiner Bomb
...alty free 3d model electric joiner bomb for download as blend on turbosquid: 3d models for games, architecture, videos. (1282185)
thingiverse
free
joiner
...joiner
thingiverse
stuff
thingiverse
free
Joiner for kerbs by racerunner
...verse
press fit this joiner to underside of kerb.
this joiner connects adjacent kerbs.
joiner is an alternative to support pier.
3dfindit
free
Joiner Set
...joiner set
3dfind.it
catalog: wilkerson
thingiverse
free
PTFE Joiner by whitefoot
...ptfe joiner by whitefoot
thingiverse
ptfe joiner for join two ptfe tubes with two m6 fittings
thingiverse
free
Beer crate joiner by boredomwontgetus
...erse
a joiner for beer crates!
this is just the upper and lower parts of the joiner. the middle part is made of coated plywood.
3dbaza
$4
Joiner Pouf (20786)
...joiner pouf (20786)
3dbaza
thingiverse
free
IKEA Lillabo joiner by MrBaz
...ikea lillabo joiner by mrbaz
thingiverse
simple plastic joiner to connect the ikea lillabo train set.
thingiverse
free
Lego Male Joiner
...lego male joiner
thingiverse
having fun
Talon
turbosquid
$8
Talon Knife
...y free 3d model talon knife for download as obj, ipt, and iam on turbosquid: 3d models for games, architecture, videos. (1348946)
turbosquid
$4
Spire of Talons
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$17
Northrop T-38 Talon
...northrop t-38 talon
3dexport
northrop t-38 talon
3d_export
free
1998 Eagle Talon TSi Turbo
...1998 eagle talon tsi turbo
3dexport
1998 eagle talon tsi turbo
turbosquid
$15
HS-12 Talon
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$110
Stealth Talon 3D Model
...force lightning raptorrocket gun offensive counter us homeland security concept
stealth talon 3d model rendersteel 72513 3dexport
3d_export
$10
Talon Sword 3D Model
...del
3dexport
sword melee game model low poly video fantasy rpg warrior blade mmo
talon sword 3d model project_zero 32037 3dexport
turbosquid
free
ME3 talon t7 heavy pistol
...l me3 talon t7 heavy pistol for download as obj, fbx, and dae on turbosquid: 3d models for games, architecture, videos. (1402804)
3d_export
$20
eagle talon tsi turbo
...s.<br>car textures:png - 2k resolution other available formats: obj, 3ds, fbx, stl, max. polycount: 34484 poly / 30158 tris
3d_export
$10
Eagle 3D Emblem 3D Model
...3d emblem 3d model 3dexport 3d logo eagle emblem talon car eagle 3d emblem 3d model gdesigns 36617...
Uav
turbosquid
$99
UAV
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$65
uav
...uav
3dexport
simple rendering of the scene file
3d_export
$5
uav
...uav
3dexport
this 3d model was specially created for 3d printing
3d_export
$60
Concept UAV
...sel generator and two electric motors.<br>uav in the form of a flying early warning radar.<br>all peace and goodness.
turbosquid
$13
UAV Drone
...rbosquid
royalty free 3d model uav drone for download as max on turbosquid: 3d models for games, architecture, videos. (1427060)
turbosquid
$40
AKINCI UAV
...oyalty free 3d model akinci uav for download as max and blend on turbosquid: 3d models for games, architecture, videos. (1617657)
turbosquid
$20
Uav Drone
...free 3d model uav drone for download as ma, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1494054)
turbosquid
$69
UAV Interceptor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
UAV Pegasus
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$42
Predator UAV 3D Model
...v 3d model
3dexport
predator uav military aircraft airplane spy unmanned drone drones
predator uav 3d model tartino 6848 3dexport
Wing
3ddd
$1
The Wing
...the wing
3ddd
wing , appledesign
the wing seating by appledesignstudio
3d_export
$5
wings
...wings
3dexport
beautiful wings model.
archibase_planet
free
Wing
...wing
archibase planet
wing decoration ornament
wing angel n180215 - 3d model (*.gsm+*.3ds+*.max) for interior 3d visualization.
3ddd
$1
Wing Chair
...wing chair
3ddd
baker , wing
wing chair
3ddd
$1
Диван WING
...диван wing
3ddd
flexform , wing
модель дивана wing
производитель: flexform
3ddd
$1
Диван WING
...диван wing
3ddd
flexform , wing
модель дивана wing
производитель: flexform
3ddd
$1
Кушетка WING
...кушетка wing
3ddd
flexform , wing
модель дкушетки wing
производитель: flexform
turbosquid
free
A-Wing
...id
free 3d model a-wing for download as fbx and unitypackage on turbosquid: 3d models for games, architecture, videos. (1164828)
3ddd
$1
Кресло Wing
...кресло wing
3ddd
wing
кресло wing из каталога в двух сочетаниях конфигурации.
3d_export
$5
wing nut
...wing nut
3dexport
wing nut