Thingiverse
Whippy Whoop by kolergy
by Thingiverse
Last crawled date: 3 years, 1 month ago
WORK IN PROGRESS
A brushed quad based on 8.5mm motors with a similar form factor as the Tiny Whoop which is made from the Blade Inductrix but much Whippier! based on a mini F3 controller.
It was used for the first woman drone race the ''Drones de dames'' which happened in Foulouse during Futurapolis see: http://www.fpv-passion.fr/course-feminine-a-toulouse-focus/
It is printed in carbon loaded nylon on a MarkForged Printer by FeelObject http://www.feelobject.fr
WORK IN PROGRESS
Verison History:
V1.2: adaptation for AIO cam & 350mah bat
V1.1.1: increased OGV thickness
V1.1: Reduced radius of & angle of guards, increased height of prop vs guards, reduced height of OGV.
V1.0.3_PRO: Added access to the programming plug, some weight optimisations
V1.0.1_PRO: Adapted to be printed on a professional printer (no need to cheat on the dimensions to get the right one)
V1.0: Cleaned-up parts & added bat wires passage.
V0.9: improved central support for F3 card & Battery & separator
V0.8: Added central support for F3 card & reinforcements on inlet lip
V0.7: Updated roll cage
V0.6: New architecture, switch to lady bird props, roll cage
V0.5:Correction of Battery support & addition of wire passages.
V0.4: Added battery support
V0.3: Added F3 board supports
V0.2: engine housing resized, whoops sized for three bladed props
V0.1: initial test version no board, battery, camera support
Design files for the older versions are in the Old.zip
Partslist:
Control Board:
Banggood: Tiny F3 EVO
Radio receiver:
Lemon-RX: satellite DSMX
Propeller/Helices:
Banggood: Lady bird props Props 5 sets
Motors/Moteurs:
Banggood: RacerStar higher power
Banggood: Hubsan H107C Motors
Amazon: Hubsan H107C Motors
Batteries:
HobbyKing: 260mAh 35c 1s batt
Banggood: 240mAh 45c 1s batt
Banggood: 260mAh 30c 1s batt (Less performant & more expensive)
All in one Cam:
Banggood: Eachine FB90 cam 500TVL 5.8G 25mW
Banggood: Eachine TX01 5.8G 25mW 40CH Cam (More expensive)
https://www.youtube.com/watch?v=TGwdJXFChrA
WORK IN PROGRESS
A brushed quad based on 8.5mm motors with a similar form factor as the Tiny Whoop which is made from the Blade Inductrix but much Whippier! based on a mini F3 controller.
It was used for the first woman drone race the ''Drones de dames'' which happened in Foulouse during Futurapolis see: http://www.fpv-passion.fr/course-feminine-a-toulouse-focus/
It is printed in carbon loaded nylon on a MarkForged Printer by FeelObject http://www.feelobject.fr
WORK IN PROGRESS
Verison History:
V1.2: adaptation for AIO cam & 350mah bat
V1.1.1: increased OGV thickness
V1.1: Reduced radius of & angle of guards, increased height of prop vs guards, reduced height of OGV.
V1.0.3_PRO: Added access to the programming plug, some weight optimisations
V1.0.1_PRO: Adapted to be printed on a professional printer (no need to cheat on the dimensions to get the right one)
V1.0: Cleaned-up parts & added bat wires passage.
V0.9: improved central support for F3 card & Battery & separator
V0.8: Added central support for F3 card & reinforcements on inlet lip
V0.7: Updated roll cage
V0.6: New architecture, switch to lady bird props, roll cage
V0.5:Correction of Battery support & addition of wire passages.
V0.4: Added battery support
V0.3: Added F3 board supports
V0.2: engine housing resized, whoops sized for three bladed props
V0.1: initial test version no board, battery, camera support
Design files for the older versions are in the Old.zip
Partslist:
Control Board:
Banggood: Tiny F3 EVO
Radio receiver:
Lemon-RX: satellite DSMX
Propeller/Helices:
Banggood: Lady bird props Props 5 sets
Motors/Moteurs:
Banggood: RacerStar higher power
Banggood: Hubsan H107C Motors
Amazon: Hubsan H107C Motors
Batteries:
HobbyKing: 260mAh 35c 1s batt
Banggood: 240mAh 45c 1s batt
Banggood: 260mAh 30c 1s batt (Less performant & more expensive)
All in one Cam:
Banggood: Eachine FB90 cam 500TVL 5.8G 25mW
Banggood: Eachine TX01 5.8G 25mW 40CH Cam (More expensive)
https://www.youtube.com/watch?v=TGwdJXFChrA
WORK IN PROGRESS
Similar models
thingiverse
free
AnisopterH8 by kolergy
...ab artilect: https://artilect.fr/dronelab/
https://www.youtube.com/watch?v=l1kky5fqe6ohttps://www.youtube.com/watch?v=z-fzyy5z10c
thingiverse
free
Toad 110 Remix - AIO FPV (Brushed 8.5mm Motors) by wiretap
...degree incline on the lower deck for a cam+vtx similar to the eachine tx02. -- added a slot on...
thingiverse
free
QuickNano by kolergy
...ttp://www.robotshop.com/en/step-up-step-down-voltage-regulator-s7v7f5.html
made in fablab artilect: https://artilect.fr/dronelab/
thingiverse
free
Hubsan H107C X4 FPV Racer Frame 110 by Hackbert
...h-600mah
1x hubsan h107c x4 (electronic)
4x m3 nylon screws
1x fpv camera fx797t 3-in-1 super mini 5.8g 40ch av video transmitter
thingiverse
free
GBMicroFPVDrone v1 by gebeclair
...-h107c-h107d-v252-jdx385-p-88012.html
240mah 1s battery for video
i use a walkera devo 7e transmitter running deviation firmware.
thingiverse
free
Anisoptera Racer by kolergy
...ect.fr/dronelab/
https://youtu.be/rcjchmlqvywhttps://youtu.be/pnofi0aoptihttps://youtu.be/dbokuyc3jxqhttps://youtu.be/y-fjjdxfxks
thingiverse
free
Super light 110mm frame for 8.5 brushed motors (Supports 65mm props!) by 3DJakob
...8t-5_8g-600tvl-25mw-40ch-mini-transmitter-camera-combo-for-fpv-multicopter-p-1053038.html
battery: 1s or 2s 300 - 700 mah battery
thingiverse
free
Cruiser Whoop by njd13
...e to remodel the battery holder for the back, but use a small ziptie for now.
included all the parts i modeled for others to use.
thingiverse
free
GBMicroFPVDrone v1.2 by gebeclair
...ted for video) to reduce interferences)
i use a walkera devo 7e transmitter running deviation firmware.
http://byoq.over-blog.com
thingiverse
free
RaGG-e Whoop Batt on top by Raggeframe
...ragg-e whoop batt on top by raggeframe
thingiverse
ragg-e whoop battery mount and cam mount
Whippy
Kolergy
thingiverse
free
AirForce Tip by kolergy
...airforce tip by kolergy
thingiverse
end bit to be 3d printed
thingiverse
free
WireGuide V0.9 by kolergy
...wireguide v0.9 by kolergy
thingiverse
wire guide for strong print: http://www.thingiverse.com/thing:329498
thingiverse
free
MiniStruder for uDelta by kolergy
...er for udelta by kolergy
thingiverse
the ministruder adapted to the udelta printer
made in fablab artilect: https://artilect.fr/
thingiverse
free
Frabjous 3mm by kolergy
...jous 3mm by kolergy
thingiverse
a scaled version of http://www.thingiverse.com/thing:12271 to use 3mm plywood or other materials
thingiverse
free
DTE by kolergy
...t;dronons tous ensembles"
aimed at providing access to drone to persons with various handicaps
https://artilect.fr/dronelab/
thingiverse
free
Ball Holder for Magnetic Bearing by kolergy
...ball holder for magnetic bearing by kolergy
thingiverse
to comme soon
thingiverse
free
Tool Holder for the Magnetic Platform by kolergy
...tool holder for the magnetic platform by kolergy
thingiverse
soon to come
thingiverse
free
SR17 Torch Holder V0.9 by kolergy
...sr17 torch holder v0.9 by kolergy
thingiverse
to come soon
thingiverse
free
Springy Clip for uDelta by kolergy
...springy clip for udelta by kolergy
thingiverse
springy clip to reduce play on delta printers adapted to the udelta
thingiverse
free
Micro Scisky Board by kolergy
...micro scisky board by kolergy
thingiverse
open scad model of the naze32 based micro scisky board
Whoop
thingiverse
free
whoop by MichaelJFPV
...whoop by michaeljfpv
thingiverse
whoop
thingiverse
free
Tiny Whoop holder for 2 whoops by d2000
...tiny whoop holder for 2 whoops by d2000
thingiverse
tiny whoop holder for 2 whoop mini drones and battery
thingiverse
free
Whoop frame by Brassekongo
...whoop frame by brassekongo
thingiverse
a tiny whoop frame
thingiverse
free
Whoop frame by Brassekongo
...whoop frame by brassekongo
thingiverse
my first whoop frame.
thingiverse
free
WHOOPS 4
...
whoops is another
big cinewhoop as addon for hyperlite tooth fairy race frame 4"
first flight https://youtu.be/xm9afwiiass
thingiverse
free
Tiny Whoop 65mm by binaryfpv
...tiny whoop 65mm by binaryfpv
thingiverse
tiny whoop 65mm
thingiverse
free
V-Tail Whoop by Mystereon
...v-tail whoop by mystereon
thingiverse
v-tail whoop .. wip
thingiverse
free
Tiny Whoop Case by 3DRCStore
...tiny whoop case by 3drcstore
thingiverse
tiny whoop case for transport.
thingiverse
free
Tiny Whoop Calibration Base
...tiny whoop calibration base
thingiverse
a base usefull to calibrate your tiny whoop
thingiverse
free
Tiny Whoop Gate by Imozeb
...tiny whoop gate by imozeb
thingiverse
custom tiny whoop gate. requires hot glue for assembly.