Thingiverse
WellCap by pyearick
by Thingiverse
Last crawled date: 3 years ago
This is a replacement well cap design for an outside well pipe.
My well pipe measures 168mm. The design inside diameter is 178mm. Please note that despite the size difference, the printed cap is not a loose fit.
Since this is a big print, I'd recommend checking your fit by printing a few layers with the open end at the bottom, stop the print and then check the diameter on your well. When you go for your final print, print it upside down with the top of the cap on the printer bed.
My well pipe measures 168mm. The design inside diameter is 178mm. Please note that despite the size difference, the printed cap is not a loose fit.
Since this is a big print, I'd recommend checking your fit by printing a few layers with the open end at the bottom, stop the print and then check the diameter on your well. When you go for your final print, print it upside down with the top of the cap on the printer bed.
Similar models
3dwarehouse
free
Stove pipe (6') clean out cap
...9; diameter stove pipe clean out cap / end. it was designed to be just large enough to fit over a 6' diameter stove pipe end.
thingiverse
free
Cap for 32.5 mm diameter PVC pipe by Kaphaak
...cap for 32.5 mm diameter pvc pipe by kaphaak
thingiverse
printed a cap for a pvc pipe with a diameter of 32.5 mm.
thingiverse
free
3/4" PVC End Cap by LoganHartford
...e scaling in your slicer.
consider printing a test ring just a couple of mm high and seeing how the ring lines up with your pipe.
thingiverse
free
friction mount snap cap for 1/2 NPT pipe by cfishy
...nt snap cap for 1/2 npt pipe by cfishy
thingiverse
printed it in pet+ and pla, it should friction fit the inner diameter nicely.
thingiverse
free
Shower drain by Fickert
...can be scaled as well to fit your shower / bath tub drain without issues. i checked sizes for scaling with common pipe diameters.
thingiverse
free
3 inch diameter pipe cap by ForrestChandler
...3 inch diameter pipe cap by forrestchandler
thingiverse
a cap for pipes.
thingiverse
free
Kenmore Central Vacuum Pipe Cap
...printing, and i had this perfectly snug press fit cap putting the vacuum back in working order. the inside diameter is 44.50 mm.
thingiverse
free
Binocular caps 47mm by ock10
...with 47mm diameters. the ribs in the caps were designed with a 0.1 mm interference fit, or 46.8mm diameter, and printed in petg.
thingiverse
free
Bahtinov Mask by TheRocketFish
.... i recommend flipping the model and doing a quick test print of the diameter to check for a proper fit before doing a full print
thingiverse
free
Buckler with hole/End cap for a metal pipe with a hole by agentsmith1612
...ter: 25,25 mm
inner diameter 22,17 mm
diameter hole: 7,9 mm
if you want i can customize it for you to your needs.
printed in pla.
Pyearick
thingiverse
free
275mm_tray by pyearick
...65mm tray. i use two strips of 1 in 3m vhb tape on the top and bottom of the back to attach the tray to the back of a vanity door
thingiverse
free
Corner Siding Mount by pyearick
... a vinyl siding corner mount with a 200+ mm arm on a 45 degree angle. i use it to mount my wyze camera at the corner of my house.
thingiverse
free
400mm Spice Tray by pyearick
... of my pantry door for spices. this is a 400x100x65 mm print that i've attached to the cabinet with 3m vhb double sided tape.
thingiverse
free
Spice Rack 8 by pyearick
...s rack as i have a lot of non-standard spice bottles.
i used 3m vhb double sided tape to mount the rack and that is working well.
thingiverse
free
Honda Clarity Galaxy Note 8 Cell Phone Holder by pyearick
...ed in about 12 hours with a raft and support. i could get it to fit in cura (vertically) but it was going to take a day to print.
thingiverse
free
GE GNSF35Z01 Water Softener Float Replacement by pyearick
... of pla. pla is porous and will take on water after a few days. petg, as i've designed the part, has proven to be watertight.