Thingiverse
Wanhao i3: MKS Gen-L, Rasp Pi, Mosfet, TMC2130 Combo Adaptor and 120mm Cooling Mod by OmNomNomagon
by Thingiverse
Last crawled date: 3 years ago
An Adaptor to convert the electronics of a wanhao i3 to the following:
MKS Gen-L
Raspi 2/3/b
Mosfet with 8mm x 63mm hole spacing, such as this one.
The Adaptor fits on top of the existing mounting holes and is secured with M3 screws and washers. The boards are mounted with M3 screws of a length of 3-6mm.
Place a piece of carboard or foam under the control board to prevent shorts.
Pics and a marlin 1.1.8 config for a working MKS Gen-L and TMC2130 are also included. Due to the cramped spacing in the case, the usual USB Type A cable will not fit without being modified. The rubberised plastic shield needs to be removed to allow the cable to bent enough to fit.
This setup works perfectly with Octopi, and the TMC drivers run cool and quiet with sensorless homing. This guide contains a great TMC2130 wiring guide. The Gen-L is the same except the AUX-3 Header is rotated 180degrees.
Previously I ran a RAMPS board, but it required a lot of modification in order to run at the 24v required for the Trinamic Drivers. After it died the GEN-L was a great cheap substitute that can natively handle the 24v without modification.
I recommend switching out the rear fan with the included 120mm adaptor to keep everything cool as the TMC drivers can generate a fair amount of heat. This shroud is as thin as physically possible. It is 5-15mm shorter than other designs. It has the power port on both the left and right sides. It works when the control box is stand alone and can be flipped 180 degrees to allow for mounting the control box to the bottom or a lack table. The other electrical port hole can be plugged with this thing
When replacing the mainboard, the original wanhao display will not work without rewiring the ribbon cables. Alternatively the Reprap Discount full graphic smart controller is a drop in replacement. With this configuration the SD card is built into the display and will be blocked when mounted into the case. however this isn't an issue when printing via octopi.
MKS Gen-L
Raspi 2/3/b
Mosfet with 8mm x 63mm hole spacing, such as this one.
The Adaptor fits on top of the existing mounting holes and is secured with M3 screws and washers. The boards are mounted with M3 screws of a length of 3-6mm.
Place a piece of carboard or foam under the control board to prevent shorts.
Pics and a marlin 1.1.8 config for a working MKS Gen-L and TMC2130 are also included. Due to the cramped spacing in the case, the usual USB Type A cable will not fit without being modified. The rubberised plastic shield needs to be removed to allow the cable to bent enough to fit.
This setup works perfectly with Octopi, and the TMC drivers run cool and quiet with sensorless homing. This guide contains a great TMC2130 wiring guide. The Gen-L is the same except the AUX-3 Header is rotated 180degrees.
Previously I ran a RAMPS board, but it required a lot of modification in order to run at the 24v required for the Trinamic Drivers. After it died the GEN-L was a great cheap substitute that can natively handle the 24v without modification.
I recommend switching out the rear fan with the included 120mm adaptor to keep everything cool as the TMC drivers can generate a fair amount of heat. This shroud is as thin as physically possible. It is 5-15mm shorter than other designs. It has the power port on both the left and right sides. It works when the control box is stand alone and can be flipped 180 degrees to allow for mounting the control box to the bottom or a lack table. The other electrical port hole can be plugged with this thing
When replacing the mainboard, the original wanhao display will not work without rewiring the ribbon cables. Alternatively the Reprap Discount full graphic smart controller is a drop in replacement. With this configuration the SD card is built into the display and will be blocked when mounted into the case. however this isn't an issue when printing via octopi.
Similar models
thingiverse
free
ALTERNATIVE MOSFET MOUNT FOR WANHAO MKS GEN-L MOUNTS by BRAINCELL
...sfet with holes at 52mmx42mm as pictured....
this is for the mks gen-l mounts as shown in the source thing by omnomnomagon.......
thingiverse
free
Super Simple MKS Gen 120mm Fan Mount by syahriansyah
...s and you'll need few m3x12mm or m4x12mm screws and nuts. i think it will be compatible with all mks boards out there. enjoy!
thingiverse
free
Wanhao i3 PSU Cover 120mm Fan Adapter With MOSFET by KingCreations
...the case and easy turn by hand. or, you could remix with holes in the top to allow better access to the msfet mounting screws.
thingiverse
free
Wanhao i3: Ramps, Rasp Pi, and Mosfet Control Box Combo Adapter by OmNomNomagon
...switch out sd cards, however this is not really an issue if you also are also moving to octopi.
i also recommend this ramps guide
thingiverse
free
Ender 3 adaptor for MKS Gen L by TotalRetribution
...quiet. also i used the e1 output to drive the hot end fan and setup marlin to only turn this fan on when the hot end is over 50c.
thingiverse
free
MKS 1.4 air tunnel for TMC drivers + fan adapter by ikarisan
...emis's redesign and it is meant to be used with my "mks gen 1.4" mount (https://www.thingiverse.com/thing:2754365).
thingiverse
free
MKS Gen L V2.0 case by Omar82
...en l v2.0 case by omar82
thingiverse
electronic case for mks gen l v2.0 with 80mm fan mount to cool the drivers & the board.
thingiverse
free
Wanhao MKS SGEN-L Motherboard/mainboard adaptor by spandit
...it using 2 of the original mounting screws.
it is designed to use sticky pads on the underside to cushion and help secure the mks
thingiverse
free
Tarantula control box and Bracket MKS GEN 1.4 by Alasterm
...ing it as a brace to improve printer stability. extra space available for cable management including cable tie attachment points.
thingiverse
free
Wanhao i3 Melzi to MKS Gen adapter by Angry_Samsquanch
...trudes a little so you may need to use longer screws with m4 nuts on the bottom if the m4 screws won't thread into the holes.
Omnomnomagon
thingiverse
free
Stealthy Faceted Wall Hook by OmNomNomagon
...erse
a faceted hook remix with a pronounced angle to allow it to hold bigger objects.
works perfectly with 3m double sided tape.
thingiverse
free
Lego Saturn V Stands by OmNomNomagon
..., one per stage. these can be a little precarious, so i created some additional stands in the same style as the originals. enjoy.
thingiverse
free
Earbuddy - Earphone holder by OmNomNomagon
...nes and buds perfectly. you may need to increase or decrease the %size depending on if your buds are larger or smaller than most.
thingiverse
free
Alco Bottle Headphone Stand by OmNomNomagon
... scotch.
update
check out my evolution of this design here
it offers a cleaner look and forms a more secure hold on the bottle.
thingiverse
free
Sturdy Filament Guide Wanhao i3 by OmNomNomagon
...atible with this filament locker https://www.thingiverse.com/thing:1280498 and other thingy's created for the original holder
thingiverse
free
Whisky Bottle headphone Stand by OmNomNomagon
...ollowing whisky bottles:
lapphroaig
lagavulin
yamasaki
jack daniels
glenfiddich
cragganmore
ardberg
glenlivet
glenmorangie
enjoy.
thingiverse
free
Z Brace Yourself by OmNomNomagon with Added Bolting Flanges by shroppy
...
i think it made the whole unit look much better than the shiny zinc plated threaded rod you get from the typical hardware store.
thingiverse
free
Low Poly Planter - Wide Top by OmNomNomagon
...ed it and included a normal (96x96x48mm) and a mini (65x65x35mm) size.
changelog
1.1. added a solid model for vase mode printing.
thingiverse
free
ReDuplicator i3 MK3x - Non Metal 3030 Tabbed Brackets by OmNomNomagon
...ner 30x30 tabbed bracket
alternate 30mm high leg file
tabbed corner plate brackets.
see the original project for complete details
thingiverse
free
Quad Vacuum Tube Display Stand - ECC88 6DJ8 6922 6BZ7 by OmNomNomagon
...22, e88cc, pcc88, e188cc, 6bz7, cca. these are the tubes commonly used in schiit audio products such as the valhalla and the lyr,
Tmc2130
thingiverse
free
Final de carrera TMC2130 endstop FLEX
...
thingiverse
endstop flex para final de carrera tmc2130 amortiguado, evita deterioro de las correas.
para fijarlo a perfil 2020.
thingiverse
free
EasyThreed Backplate for replacing SKR 1.X with TMC2130
...f my project: replace original board with skr 1.3 or skr 1.x and tmc 2230
easythreed backplate for replacing skr 1.x with tmc2130
thingiverse
free
Anycubic Trigorilla stepper driver cooling tunnel for TMC2130 by MakeTo3D
...se with tmc2130 with spi control.
cutting the lateral helps to be able to cross the spi cables through it.
a 5015 blower is used.
thingiverse
free
JGAurora A5 TMC2130 cooling fan duct by heindaddel
...addel
thingiverse
designed for the use of a 5015 24v radial fan, 4mm space underneath for internal wiring.
added xy-only version
thingiverse
free
Anycubic 40x40 driver fan (Works with TMC2130) by Yakandu
...30) by yakandu
thingiverse
anycubic delta/kossel tri-gorilla board stepper motor driver cooler tunnel.
easy to print.
m3 screws.
thingiverse
free
TMC2130 RAMPS/Re-ARM Adapter PCB by salfter
...know about zipfiles, remove ".thing" from the end of displaytmcadapter.zip.thing to get to the kicad files and gerbers.
thingiverse
free
3DSteel - P3Steel Version with TMC2130 SPI, Marlin 2, Bed leveling, and HTA3D v2 extruder
...3dsteel - p3steel version with tmc2130 spi, marlin 2, bed leveling, and hta3d v2 extruder
thingiverse
more info:www.hta3d.com
thingiverse
free
Rumba shield for TMC2130 + LCD + BL-touch / servo by TimotheFrignac
...and only ask 5 (the price of the board is the same if you order 10pcs, but the shipping cost is calculated accordingly to weight)
thingiverse
free
TMC2130 Trigorilla cooling tunnel by masterviana
...for control tmc2310 and still have good air flow through steppers its uses a 5020 blow fan.
print upsidedown with supports.
enjoy
thingiverse
free
Final de Carrera TMC endstop flex
...endstop flex thingiverse topes flexibles para final de carrera tmc2130 ...
Rasp
turbosquid
$5
Rasp
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$19
Rasp fish
...lty free 3d model rasp fish for download as 3ds, max, and obj on turbosquid: 3d models for games, architecture, videos. (1368235)
turbosquid
$19
Rasp fish 2
...y free 3d model rasp fish 2 for download as 3ds, max, and obj on turbosquid: 3d models for games, architecture, videos. (1368472)
turbosquid
$10
Craftsman Handtools - Rasp
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Scroll Armchair
...finish (each piece will vary), which includes "worm holes," raspng, and rub through. it is natural for the rattan...
thingiverse
free
Rasp handle for 3mm rasps by joujo1212
...handle for small rasps with diameter 3mm.
more details on blog (sk): http://blog.orenic.me/kutilska-3d-sobota-1-prepazky-a-madla/
thingiverse
free
BOLILE RASP
...bolile rasp
thingiverse
bolile rasp 2.0 .
desined for balls of 20mm.
thingiverse
free
RASP HOlder by lory90sw
...rasp holder by lory90sw
thingiverse
i design it with solidworks is a very useful gadject to hold your rasp in order
thingiverse
free
Rasp Handle by christophermurphy
...or the rasps in my woodshop class. the students should have an easier time holding onto these handles rather than the bare metal!
thingiverse
free
Rasp Stand 10 + 1 by ToshiTea
...rasp stand 10 + 1 by toshitea
thingiverse
this is a stand for 10 diamond rasps which i use to smooth my printings.
Mosfet
3d_export
$5
IC SMD Package TO263
...used for different types of semiconductors, such as transistor, mosfet voltage regulators and etcetra. a surface mount device for...
thingiverse
free
Support Mosfet
...support mosfet
thingiverse
support mosfet
remplissage 20%
thingiverse
free
i3 MOSFET Holder / i3 MOSFET Halter by JMDesigns
...i3 mosfet holder / i3 mosfet halter by jmdesigns
thingiverse
i3 mosfet holder / i3 mosfet halter
thingiverse
free
MOSFET Holder / MOSFET Halter 20x20 Extrusion by JMDesigns
...mosfet holder / mosfet halter 20x20 extrusion by jmdesigns
thingiverse
mosfet holder / mosfet halter 20x20 extrusion
thingiverse
free
TO-220 MOSFET Holder
...to-220 mosfet holder
thingiverse
this will hold 3x to-220 mosfets. the mosfets will snap into place.
free3d
free
MOSFET
...mosfet
free3d
metal oxide semiconductor field effect transistor
thingiverse
free
Double Mosfet Holder for Lerdge Mosfet Board by LorDXEO
... board by lordxeo
thingiverse
dual mosfet holder for lergde mosfet modules.
holes for m3 screws, you can also use brass inserts.
thingiverse
free
MOSFET Case by Nbbwarhammer
...mosfet case by nbbwarhammer
thingiverse
a case for mosfet.
thingiverse
free
MOSFET Support
...
2 3mm screws
design
i have uploaded the freecad design that i made, so you can remix it and mod it.
i hope it is useful for you!
thingiverse
free
mosfet holders by paulsonia
...mosfet holders by paulsonia
thingiverse
two mosfet holders
Wanhao
thingiverse
free
Wanhao Logo Plate / Wanhao Logo Schild by JMDesigns
...wanhao logo plate / wanhao logo schild by jmdesigns
thingiverse
wanhao logo plate / wanhao logo schild
thingiverse
free
Wanhao logo by nebtio
...wanhao logo by nebtio
thingiverse
wanhao logo
thingiverse
free
Wanhao keychain by Rein3003
...wanhao keychain by rein3003
thingiverse
a keychain with the logo of wanhao
thingiverse
free
Wanhao Di3 v2 Light / Wanhao Di3 v2 Beleuchtung by JMDesigns
...wanhao di3 v2 light / wanhao di3 v2 beleuchtung by jmdesigns
thingiverse
wanhao di3 v2 light / wanhao di3 v2 beleuchtung
thingiverse
free
TUSH For Wanhao by wtmi1992
...tush for wanhao by wtmi1992
thingiverse
the ultimate spool holder, modified for the top of the wanhao control box. fits snug.
thingiverse
free
fanduct wanhao d12 by theopoilmek
...fanduct wanhao d12 by theopoilmek
thingiverse
fanduct pour wanhao d12
thingiverse
free
Wanhao i3 Marlin by johan21
...wanhao i3 marlin by johan21
thingiverse
marlin for wanhao i3 rampsboard 1.4.
thingiverse
free
Wanhao Duplicator i3 by imagineering4
...wanhao duplicator i3 by imagineering4
thingiverse
these are the stl files for the improvements to the wanhao duplicator i3, v2
thingiverse
free
Wanhao D6 filament guard
...wanhao d6 filament guard
thingiverse
this is a filament guard for wanhao d6 machine to avoid the filament unrolling
thingiverse
free
Wanhao Duplicator i3 Model by Hilde3D
...wanhao duplicator i3 model by hilde3d
thingiverse
wanhao duplicator i3 model
Adaptor
turbosquid
$15
Adaptor-2
...alty free 3d model adaptor-2model for download as dwg and ige on turbosquid: 3d models for games, architecture, videos. (1710809)
turbosquid
free
Adaptor plug
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Male DFP adaptor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Female VGA Adaptor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Male VGA Adaptor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$18
Memory stick adaptor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
male union tee adaptor
...ame is male union tee adaptor , it is used in home and industrial area . if you want to get yhis parts blue print buy it from me
turbosquid
$20
Male M1 Digital Adaptor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Male M1 Digital & Analog Adaptor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$10
Samsung Travel Adapter 3D Model
...samsung travel adapter 3d model 3dexport charger white travel adaptor battery charging device samsung travel adapter 3d model g.lex...
120Mm
turbosquid
$20
M829A3 120mm, APFSDS-T
...alty free 3d model m829a3 120mm, apfsds-t for download as obj on turbosquid: 3d models for games, architecture, videos. (1219997)
turbosquid
$79
M-75 120mm Mortar
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Lian Li 120mm Spider Fan Guard 3D Model
...d 3d model
3dexport
lian li 120mm spider fan guard cooler pt-g05
lian li 120mm spider fan guard 3d model mackandco 37968 3dexport
turbosquid
$69
QF 120mm Mk VIII naval gun
...mm mk viii naval gun for download as lwo, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1430519)
3d_export
$5
Ammo box tank shell 120mm
...hell 120mm
3dexport
nato box for tank ammunition caliber 120-125mm 3d format:fbx,obj,3ds max 2013 texture only diffuse 1024x1024
3ddd
$1
Черепашка
...черепашка 3ddd черепаха l-450mm,w-350mm, h-120mm ...
3d_export
$5
pantera decorativa
...pantera decorativa 3dexport pantera decorativa de 120mm de largo, 43mm de ancho y 42mm de...
3ddd
$1
Светильник точечный
...с хрустальными подвесками фирмы asfour. размеры: диаметр 77mm, высота 120mm ...
3ddd
$1
Свечи #1
...3ddd свеча производитель: - модель: свечи размеры: w-40/65mm, d-40/65mm, h-70/120mm ...
3ddd
$1
Архитектурная подсветка
...направленный светильник страна / country: китай габариты :235mm h 120mm защита...
Combo
turbosquid
$25
combo
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$79
Mannequin Combo
...uid
royalty free 3d model mannequin combo for download as ma on turbosquid: 3d models for games, architecture, videos. (1172062)
turbosquid
$15
COMBO SOFA
...ty free 3d model combo sofa for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1558534)
turbosquid
$6
Combo Door
...e 3d model combo door for download as ma, max, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1273913)
turbosquid
$225
Eyes-Combo
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$55
COMBO (Boots)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Appliances !!COMBO!!
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
combo chair
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
Computador Combo
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$100
FAHU With Combo Heater
...alty free 3d model fahu with combo heater for download as max on turbosquid: 3d models for games, architecture, videos. (1259461)
Gen
turbosquid
$15
gen
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
Gen. Rifle
...bosquid
royalty free 3d model gen. rifle for download as fbx on turbosquid: 3d models for games, architecture, videos. (1374075)
3d_export
$8
pokemon sprite voxel 1 gen
...pokemon sprite voxel 1 gen
3dexport
pokemon voxel 1 gen
turbosquid
$45
Chest Next-Gen
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$39
Nano 6th Gen
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$8
pokemon sprite voxel 7 gen
...pokemon sprite voxel 7 gen
3dexport
pokemon sprite voxel 7 gen
3d_export
$8
pokemon sprite voxel 5 gen
...pokemon sprite voxel 5 gen
3dexport
pokemon sprite voxel 5 gen
3d_export
$8
pokemon sprite voxel 3 gen
...pokemon sprite voxel 3 gen
3dexport
pokemon sprite voxel 3 gen
3d_export
$8
pokemon sprite voxel 4 gen
...pokemon sprite voxel 4 gen
3dexport
4 gen pokemon voxel sprites
3d_export
$8
pokemon sprite voxel 2 gen
...pokemon sprite voxel 2 gen
3dexport
pokemon sprite voxel 2 gen
Mks
3d_export
$5
scorpion mk
...scorpion mk
3dexport
scorpion mk .zpr,stl,obj,stl,
turbosquid
$6
MK 11
...turbosquid
royalty free 3d model mk 11 for download as blend on turbosquid: 3d models for games, architecture, videos. (1223895)
3d_export
$5
Qubeley MK-II
...qubeley mk-ii
3dexport
3d lowpoly type qubeley mk-ii
turbosquid
$3
MK killer
...lty free 3d model mk killer for download as fbx, obj, and 3ds on turbosquid: 3d models for games, architecture, videos. (1638698)
turbosquid
$25
Valentine Mk
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Mk-16
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$7
Mk-16
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
mk-2
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$25
Merkava MK 1 3D Model
... 1 3d model
3dexport
merkava mk-1 tank low-poly model maya mk1 mk mk-2 mk-3 israel army
merkava mk 1 3d model rom64 5311 3dexport
3ddd
$1
мясорубка Panasonic MK G1800P
...мясорубка panasonic mk g1800p
3ddd
мясорубка , panasonic
мясорубка panasonic mk g1800p
I3
3d_export
$10
suv i3
...suv i3
3dexport
suv i3 2013 series
3d_ocean
$89
BMW i3 2012
...y, in real units of measurement, qualitatively and maximally close to the original. model formats: - *.max (3ds max 2008 scanl...
cg_studio
$99
BMW i3 20143d model
...
cgstudio
.3ds .c4d .fbx .lwo .max .obj - bmw i3 2014 3d model, royalty free license available, instant download after purchase.
cg_studio
$99
BMW i3 20123d model
...tudio
.3ds .c4d .fbx .lwo .max .mb .obj - bmw i3 2012 3d model, royalty free license available, instant download after purchase.
cg_studio
$99
BMW i3 20143d model
...tudio
.3ds .c4d .fbx .lwo .max .mb .obj - bmw i3 2014 3d model, royalty free license available, instant download after purchase.
humster3d
$75
3D model of BMW i3 2014
...
buy a detailed 3d model of bmw i3 2014 in various file formats. all our 3d models were created maximally close to the original.
humster3d
$40
3D model of Kitchen Set I3
...uy a detailed 3d model of kitchen set i3 in various file formats. all our 3d models were created maximally close to the original.
3d_ocean
$30
Kitchen set i3
...ensils oven plates shelves sink table ware
kitchen set i3 include 3d models: cooker, oven, sink, cupboards, table, chair, plates.
3d_ocean
$89
BMW i3 2014
...y, in real units of measurement, qualitatively and maximally close to the original. model formats: - *.max (3ds max 2008 scanl...
cg_studio
$99
BMW i3 Concept 20113d model
...i3
.3ds .c4d .fbx .lwo .max .obj - bmw i3 concept 2011 3d model, royalty free license available, instant download after purchase.
Mod
design_connected
$13
MOD. 4233 - MOD. 4234 Table Lamp
...mod. 4233 - mod. 4234 table lamp
designconnected
arcahorn mod. 4233 - mod. 4234 table lamp computer generated 3d model.
design_connected
$11
MOD.1095
...mod.1095
designconnected
mod.1095 computer generated 3d model. designed by sarfatti, gino.
3ddd
$1
fireplaces mod Spec
...fireplaces mod spec
3ddd
камин
fireplaces mod spec 180x90x125h
3ddd
free
Flos Mod. 2129
... mod
фабрика: flos
модель: mod. 2129
описание: подвесной светильник, металл, белый, черный.
сайт: www.flos.com
turbosquid
$34
Mod Lamp.c4d
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$32
MOD A 001
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$29
Maars Mod
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
Mod 70..
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
MOD Sofa
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
Mod-Lite
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Pi
design_connected
$11
Pi
...pi
designconnected
ligne roset pi chairs computer generated 3d model. designed by thibault desombre.
3d_export
$5
raspberry pi
...raspberry pi
3dexport
carcasa para la raspberry pi
turbosquid
$18
pied
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Emme pi light
...emme pi light
3ddd
emme pi light
люста emme pi light
3ddd
$1
Emme pi light
...emme pi light
3ddd
emme pi light
бра классическое emme pi light
3ddd
$1
Emme Pi Light
...emme pi light
3ddd
emme pi light
3ddd
$1
Emme Pi Light
...emme pi light
3ddd
emme pi light
design_connected
$16
Pi-Air
...pi-air
designconnected
living divani pi-air lounge chairs computer generated 3d model. designed by harry & camila.
3d_ocean
$15
Manneken Pis
...picting a naked little boy urinating into a fountain’s basin. (wikipedia) the model was sculpted in blender 2.70a rendered wit...
3ddd
$1
Emme pi light
...emme pi light
3ddd
emme pi light
люстра классическая фирма: emme pi light
артикул: 3595/5/cot/12/wh
Cooling
turbosquid
free
Cool Inc. Cool Box
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
cool penguin
...cool penguin
3dexport
cool penguin
turbosquid
$1
cooling
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$26
cooling tower
...ers.<br>model with full detail in real size. all nodes and bolted connections are built. it was designed for nuclear power.
3ddd
$1
Mantra Cool
...14 версиях и obj-файл, а также материал для включенного и для выключенного светильника. turbosmooth/meshsmooth при необходимости.
3d_export
$5
cool electric guitar
...cool electric guitar
3dexport
cool electric guitar
turbosquid
$5
Cooling glass
...quid
royalty free 3d model cooling glass for download as obj on turbosquid: 3d models for games, architecture, videos. (1193829)
turbosquid
$30
CPU Cooling
...royalty free 3d model cpu cooling for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1386263)
turbosquid
$5
Cool CLoud
...
royalty free 3d model cool cloud for download as ma and obj on turbosquid: 3d models for games, architecture, videos. (1572300)
3d_export
$5
table cooling fan
...table cooling fan
3dexport
table cooling fan made of black plastic. individual small size cooling fan for office desk.