Thingiverse
Wanhao Duplicator i3 Plus / Monoprice Maker Select Plus Z-Axis bracing (all required parts) by mattcaron
by Thingiverse
Last crawled date: 3 years ago
Introduction:
When printing my Z braces for the Plus, I found that it was a bunch of "take this part from here, this part from there, etc." and I ended up printing some parts I didn't need. Therefore, I decided to remix the parts I used into a "one stop shop".
You will need to print:
4 of the BallsMk2
1 of everything else
I note that I did not bother with the nut plugs, so I don't know if they will actually work. I've included them for completeness.
You will need the following hardware:
2 pieces 5/16 or 8mm threaded rod at least 16.5" long (approx 420mm). I used 18" long pieces (457mm) because 36in (914mm) is a common length in the US.
2 nylock nuts in the above width and thread.
6 regular nuts in the above width and thread.
4 M5 x 10 screws (for the front and rear corner feet, replacing the stock screws, which are too short)
8 M3 x 10 screws (for the top left and right corners, replacing the stock screws, which are too short)
Instructions:
With some pliers, pop out the the round plug, in the middle of the ball, which is is for support and it will pull out cleanly with needle nose pliers; so you do not need to enable support in your slicer for the balls.
Undo the 4 screws on one side of the gantry and put on that side top bracket with 4 of the M3 x 10 screws. Try to get the corner back in the original position, because you don't want to knock your gantry out of square.
Repeat step 1 for the other side.
Undo the left and right rear screws (leaving the center one alone) and put on the two back feet using 2 M5 x 10 screws.
Take your threaded rod and thread a regular nut on to it, and fit it into one of the front feet so that the threaded rod protrudes past the bottom of the foot.
Add a nylock nut to the end of the rod so the flat part faces the interior of the foot.
Pull the rod up so that the nut seats inside the foot.
Tighten down on the regular nut so the foot is tight.
From the other end of the threaded rod, add another regular nut and one of the balls. The ball should cover the nut, and you want it to go down far enough to give you enough space to get the rod through the bracket on the gantry.
Remove the screw from the front corner appropriate to where you are going to install the foot.
Sliding the threaded rod up through the top bracket, install the foot.
As you are sliding the threaded rod in to the upper support, add a ball and a regular nut, as you won't have clearance to screw them on once everything is tight.
Once the foot is in place, use an M5 x 10 screw to screw it down.
Repeat the above steps for the opposite side bracket.
Once both brackets are on and the balls containing the nuts can be turned freely, loosen the screws at the bottom of the gantry (the ones you had to put in when you first got the printer) and use the balls to square up the printer, tightening them at the end. Then tighten down the screws.
Now everything should be good and square.
When printing my Z braces for the Plus, I found that it was a bunch of "take this part from here, this part from there, etc." and I ended up printing some parts I didn't need. Therefore, I decided to remix the parts I used into a "one stop shop".
You will need to print:
4 of the BallsMk2
1 of everything else
I note that I did not bother with the nut plugs, so I don't know if they will actually work. I've included them for completeness.
You will need the following hardware:
2 pieces 5/16 or 8mm threaded rod at least 16.5" long (approx 420mm). I used 18" long pieces (457mm) because 36in (914mm) is a common length in the US.
2 nylock nuts in the above width and thread.
6 regular nuts in the above width and thread.
4 M5 x 10 screws (for the front and rear corner feet, replacing the stock screws, which are too short)
8 M3 x 10 screws (for the top left and right corners, replacing the stock screws, which are too short)
Instructions:
With some pliers, pop out the the round plug, in the middle of the ball, which is is for support and it will pull out cleanly with needle nose pliers; so you do not need to enable support in your slicer for the balls.
Undo the 4 screws on one side of the gantry and put on that side top bracket with 4 of the M3 x 10 screws. Try to get the corner back in the original position, because you don't want to knock your gantry out of square.
Repeat step 1 for the other side.
Undo the left and right rear screws (leaving the center one alone) and put on the two back feet using 2 M5 x 10 screws.
Take your threaded rod and thread a regular nut on to it, and fit it into one of the front feet so that the threaded rod protrudes past the bottom of the foot.
Add a nylock nut to the end of the rod so the flat part faces the interior of the foot.
Pull the rod up so that the nut seats inside the foot.
Tighten down on the regular nut so the foot is tight.
From the other end of the threaded rod, add another regular nut and one of the balls. The ball should cover the nut, and you want it to go down far enough to give you enough space to get the rod through the bracket on the gantry.
Remove the screw from the front corner appropriate to where you are going to install the foot.
Sliding the threaded rod up through the top bracket, install the foot.
As you are sliding the threaded rod in to the upper support, add a ball and a regular nut, as you won't have clearance to screw them on once everything is tight.
Once the foot is in place, use an M5 x 10 screw to screw it down.
Repeat the above steps for the opposite side bracket.
Once both brackets are on and the balls containing the nuts can be turned freely, loosen the screws at the bottom of the gantry (the ones you had to put in when you first got the printer) and use the balls to square up the printer, tightening them at the end. Then tighten down the screws.
Now everything should be good and square.
Similar models
thingiverse
free
Shower Curtain Rod Support by amwatts
...ill pass through the holes in the links and attach to the nut on the other side. do not tighten too much or your part will crack.
thingiverse
free
The heavy brackets for CR10 S5 by NTRANCE
... 20-30 nm, for the allen screws about 5-10 nm.
once a year re-tighten nuts & bolts and afterwards re-level the bed.
have fun!
thingiverse
free
Filament Spool Holder Mod for Malyan M150 and I3 Clones by paradug
...paradug thingiverse this modification of the malyan m150's (or similar i3 clones) stock filament holder improves the filament feed...
thingiverse
free
Tevo Tornado Feet (M5 screws) by Didtoknan
...- remove the bracket
3- reinstall the bracket on top of the 20x20 extrusion
4- install the foot (3 m5x16 or m5x18 and 3 m5 t-nut)
thingiverse
free
Artillery Sidewinder X1 V4 Gantry Support by Minkio95
...olution, the top surface of the diagonal hole will be "stepped" and you will have more grip when you will fix the nuts.
thingiverse
free
MakerFarm Y Bed LM8UU Bearing Brackets by schoonerburger
...d and not rub along the smooth rods.
i replaced the #6 bolts with m3 screws mounted from the bottom and nylock nuts on the top.
thingiverse
free
5/16 threaded rod Z-brace for Tevo Tarantula by teikjoon
...e brackets are not load bearing, they just need to be stiff enough to prevent the z gantry from oscillating as the hot end moves!
thingiverse
free
3D printed table legs by spegelius
...here in case you want to make changes to the desing: https://github.com/spegelius/3dmodels/blob/master/table_legs/table_legs.scad
thingiverse
free
Delta Counterbalance by BobDavis73
... pulleys are sized for para-cord. if you use the corner tap an m5 thread into the center of the aluminum extrusion for mounting.
thingiverse
free
X-Carve mounting bracket by matt448
...threads. i used low profile m5 screws to attach it to the x-carve and then regular cap head m5 screws to attach it to the bench.
Mattcaron
thingiverse
free
Leveling prints by mattcaron
... then adjust the print bed on the fly until the extrusion looks good. then stop the print, pull it off, and print something real.
thingiverse
free
Otrio Pegs and Rings by mattcaron
...ayer game. so, i modeled these so that a 4th person could play. this also allowed people to pick the colors for their own pieces.
thingiverse
free
Axle for 608 bearing by mattcaron
...ess. so, i made this axle from a finger cap by adding two flat spots. now it is suspended above the recess and works rather well.
thingiverse
free
Wooden train peg. by mattcaron
...hey tend to break the pegs. so, i made a replacement that i could print rather than making them by hand, which is time consuming.
thingiverse
free
Grocery cart wheel chock by mattcaron
...o fit that width and diameter wheel. it may work for other countries' carts; but i don't know what size their wheels are.
thingiverse
free
LACK table legs by mattcaron
...mething at the top to stop it from falling forward. right now, i use a small clamp on the table, but any type of catch will work.
thingiverse
free
Tin Lizzie laser mount by mattcaron
...a batteries. you'll need something to keep it turned on - this switch is what i use:
https://www.thingiverse.com/thing:956525
thingiverse
free
.grip modular handle cork vices by mattcaron
...fit, but i wasn't happy with the stability, which is what the larger one is for. it's sized for belgian-style beer corks.
Monoprice
thingiverse
free
Display frame for Monoprice MP10
...display frame for monoprice mp10
thingiverse
display frame for monoprice mp10
thingiverse
free
Bridge covers Monoprice MP10
...bridge covers monoprice mp10
thingiverse
bridge covers monoprice mp10
thingiverse
free
Monoprice Coin by Peyton_Guyot
...monoprice coin by peyton_guyot
thingiverse
print this!
thingiverse
free
Voxel Monoprice spool holder by avalero
...voxel monoprice spool holder by avalero
thingiverse
voxel monoprice spool holder
thingiverse
free
Monoprice select mini knob by BramRausch
...monoprice select mini knob by bramrausch
thingiverse
this is a replacement knob for the monoprice select mini.
thingiverse
free
Monoprice 3d printer hook by dmitriyf
...monoprice 3d printer hook by dmitriyf
thingiverse
this is an attachment to monoprice select 3d printer v2
thingiverse
free
monoprice ultimate spool mount by death4u
...older by danmannert to monoprice ultimate 3d printer. it clips into the slot on the top of the printer for the optional enclosue.
thingiverse
free
Monoprice Mini Delta Foot
...a foot for a monoprice mini delta. it helps to increase airflow under the printer. it also helps to reduce the volume of the fan.
thingiverse
free
Monoprice Select Mini Fan Guard
...y fan protection. this is an essential upgrade.
used it on the monoprice select mini pro (from www.3dprinthings.be).
perfect fit!
thingiverse
free
Monoprice Cable Tie Mount
... but had to cut down the straps a bit to make them work. designed a quick mount that fits the full strap, item 6457 on monoprice.
Wanhao
thingiverse
free
Wanhao Logo Plate / Wanhao Logo Schild by JMDesigns
...wanhao logo plate / wanhao logo schild by jmdesigns
thingiverse
wanhao logo plate / wanhao logo schild
thingiverse
free
Wanhao logo by nebtio
...wanhao logo by nebtio
thingiverse
wanhao logo
thingiverse
free
Wanhao keychain by Rein3003
...wanhao keychain by rein3003
thingiverse
a keychain with the logo of wanhao
thingiverse
free
Wanhao Di3 v2 Light / Wanhao Di3 v2 Beleuchtung by JMDesigns
...wanhao di3 v2 light / wanhao di3 v2 beleuchtung by jmdesigns
thingiverse
wanhao di3 v2 light / wanhao di3 v2 beleuchtung
thingiverse
free
TUSH For Wanhao by wtmi1992
...tush for wanhao by wtmi1992
thingiverse
the ultimate spool holder, modified for the top of the wanhao control box. fits snug.
thingiverse
free
fanduct wanhao d12 by theopoilmek
...fanduct wanhao d12 by theopoilmek
thingiverse
fanduct pour wanhao d12
thingiverse
free
Wanhao i3 Marlin by johan21
...wanhao i3 marlin by johan21
thingiverse
marlin for wanhao i3 rampsboard 1.4.
thingiverse
free
Wanhao Duplicator i3 by imagineering4
...wanhao duplicator i3 by imagineering4
thingiverse
these are the stl files for the improvements to the wanhao duplicator i3, v2
thingiverse
free
Wanhao D6 filament guard
...wanhao d6 filament guard
thingiverse
this is a filament guard for wanhao d6 machine to avoid the filament unrolling
thingiverse
free
Wanhao Duplicator i3 Model by Hilde3D
...wanhao duplicator i3 model by hilde3d
thingiverse
wanhao duplicator i3 model
Duplicator
turbosquid
$10
duplicate
...
turbosquid
royalty free 3d model duplicate for download as on turbosquid: 3d models for games, architecture, videos. (1566034)
turbosquid
$20
Wonderful duplicate kids room
...ul duplicate kids room for download as skp, 3ds, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1609462)
archive3d
free
Copier 3D Model
...hine duplicating machine
copier n160808 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$30
connect four set
...ate objects that can be disassembled. includes one red and one black checker which can be duplicated to the standard 42 checkers.
3ddd
$1
Черепица
...del
- put it in your scene and duplicate
- level of detail can be edited
- open with 3ds max 2010-2013 or import in your program.
3d_export
$27
Dividing Cell / Ovule 3D Model
...al microbe blob ovum fiction science ovule duplication divide dividing
dividing cell / ovule 3d model duchampmodels 9691 3dexport
3d_ocean
$16
Folding Chair
...tubing. designed to be good low poly at a distance and mesh smooth pretty well and light weight for duplicating a lot. package...
3d_export
$8
wooden fence
... one post separate so the fence can be duplicated and extended. created in blender 3.0 file format fbx with texture painted maps.
3d_export
$8
wooden fence
... one post separate so the fence can be duplicated and extended. created in blender 3.0 file format fbx with texture painted maps.
3d_ocean
$2
DNA Strands Of 5 Types
... strands that can be multiplied and can be made long chains by duplicating them and can be easily applied materials and textures.
Bracing
archive3d
free
Bracing 3D Model
...
holder bracing strengthening
bracing 4 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archive3d
free
Bracing 3D Model
...
bracing strengthening holder
bracing 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$5
brace PARIS
...osquid
royalty free 3d model brace paris for download as max on turbosquid: 3d models for games, architecture, videos. (1284415)
archive3d
free
Bracing 3D Model
...older fastening strengthening
bracing 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archive3d
free
Bracing 3D Model
...older fastening strengthening
bracing 3 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$20
Corner Brace Bracket
...oyalty free 3d model corner brace bracket for download as stl on turbosquid: 3d models for games, architecture, videos. (1322777)
turbosquid
$10
Craftsman Handtools - Brace
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
Degree Brace 4
...el degree brace 4 for download as 3ds, max, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1205705)
turbosquid
$1
Degree Brace 3
...el degree brace 3 for download as 3ds, max, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1205719)
turbosquid
$1
Degree Brace 2
...el degree brace 2 for download as 3ds, max, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1205714)
I3
3d_export
$10
suv i3
...suv i3
3dexport
suv i3 2013 series
3d_ocean
$89
BMW i3 2012
...y, in real units of measurement, qualitatively and maximally close to the original. model formats: - *.max (3ds max 2008 scanl...
cg_studio
$99
BMW i3 20143d model
...
cgstudio
.3ds .c4d .fbx .lwo .max .obj - bmw i3 2014 3d model, royalty free license available, instant download after purchase.
cg_studio
$99
BMW i3 20123d model
...tudio
.3ds .c4d .fbx .lwo .max .mb .obj - bmw i3 2012 3d model, royalty free license available, instant download after purchase.
cg_studio
$99
BMW i3 20143d model
...tudio
.3ds .c4d .fbx .lwo .max .mb .obj - bmw i3 2014 3d model, royalty free license available, instant download after purchase.
humster3d
$75
3D model of BMW i3 2014
...
buy a detailed 3d model of bmw i3 2014 in various file formats. all our 3d models were created maximally close to the original.
humster3d
$40
3D model of Kitchen Set I3
...uy a detailed 3d model of kitchen set i3 in various file formats. all our 3d models were created maximally close to the original.
3d_ocean
$30
Kitchen set i3
...ensils oven plates shelves sink table ware
kitchen set i3 include 3d models: cooker, oven, sink, cupboards, table, chair, plates.
3d_ocean
$89
BMW i3 2014
...y, in real units of measurement, qualitatively and maximally close to the original. model formats: - *.max (3ds max 2008 scanl...
cg_studio
$99
BMW i3 Concept 20113d model
...i3
.3ds .c4d .fbx .lwo .max .obj - bmw i3 concept 2011 3d model, royalty free license available, instant download after purchase.
Select
3ddd
$1
TUBADZIN SELECT
...max 2014, 2011.
fbx 2014, 2013, 2011,
obj
_____________________________________http://www.tubadzin.pl/en/collection/324
3ddd
$1
Плитка Selection
... supergres , плитка
плитка selection - supergres ceramiche
turbosquid
$15
Christmas Selection
...royalty free 3d model christmas selection for download as fbx on turbosquid: 3d models for games, architecture, videos. (1696333)
turbosquid
$39
Vases selection
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
SELECTIVE RACKING SYSTEM
...yalty free 3d model selective racking system for download as on turbosquid: 3d models for games, architecture, videos. (1282512)
turbosquid
$10
Hansgrohe ShowerTablet Select
...ee 3d model hansgrohe showertablet select for download as max on turbosquid: 3d models for games, architecture, videos. (1336955)
turbosquid
$29
Chill selectional sofa
...odel chill selectional sofa for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1465691)
3ddd
free
Lunaria - Nova, ASA Selection
... asa selection , dried flowers
ветка лунарии в вазе nova, asa selection
3ddd
$1
inno SELECT SLIM chair
...inno select slim chair
3ddd
inno
high detailed inno select slim chair
turbosquid
$29
Select Chaise Lounge
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Plus
turbosquid
$2
plus-plus puzzle and lego
...d model plus-plus puzzle and lego for download as stl and obj on turbosquid: 3d models for games, architecture, videos. (1662633)
3ddd
$1
Стенка Plus
...стенка plus
3ddd
plus , модная мебель
фабрика "модная мебель", модель plus
3ddd
$1
Спальня METIS plus
... hulsta , metis , спальня
спальня metis plus
design_connected
$11
be plus B+
...be plus b+
designconnected
blå station be plus b+ chairs computer generated 3d model. designed by börge lindau.
design_connected
$11
Bank Plus
...bank plus
designconnected
röthlisberger kollektion bank plus coffee tables computer generated 3d model. designed by atelier oi.
3ddd
$1
elos Plus
... candela
elos plus — мультифункциональный аппарат для проведения лазерного и ipl лечений
3ddd
$1
Calligaris Even Plus
...calligaris even plus
3ddd
calligaris
calligaris_chair_even plus
design_connected
$29
Basket Plus
...nconnected
photo-realistic 3d models of the basket plus bed from bonaldo for 3d architectural and interior design presentations.
3ddd
free
Artpole Faktum Plus
... артполе , панель
artpole faktum plus
размеры:
высота 625мм
ширина 800мм
глубина 17мм
3ddd
$1
Мария / Jazz Plus
...мария / jazz plus
3ddd
мария
кухня фабрики мария модель__jazz plus
Axis
3ddd
$1
Мария Axis
...
3ddd
кухня , классическая , axis
модель кухни.
3d_export
$22
Axis robot 6-axis robotic arm
...ing parts drawings, standard parts purchased parts list, can be produced directly according to the drawings, welcome to download!
3ddd
free
Versatile Axis
...ddd
nexus , плитка
http://bvtileandstone.com/ceramic-porcelain/versatile-axis/
3d_export
$19
robot 2 axis
...robot 2 axis
3dexport
robot 2 axis
turbosquid
$40
Axis R5F
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$40
Axis S5F
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$30
Axis Athlon
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Linear Axis
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$15
drawing axis
...drawing axis
3dexport
simple rendering of the scene file
3ddd
$1
versatile axis ARC
...versatile axis arc
3ddd
versatile , плитка
versatile axis arc red dot design award
Z
3d_export
$5
nissan z
...nissan z
3dexport
nissan z
3ddd
$1
Vase Z
...vase z
3ddd
vase z
3ddd
$1
полотенцесушить Z
...полотенцесушить z
3ddd
полотенцесушитель
полотенцесушить z
design_connected
free
Z-Chair
...z-chair
designconnected
free 3d model of z-chair designed by karman, aleksei.
design_connected
$11
Z Lamp
...z lamp
designconnected
phillips z lamp computer generated 3d model. designed by kalff, louis.
3d_export
$5
Dragon balls z
...dragon balls z
3dexport
dragon ball z
turbosquid
$20
Fighter Z
...
turbosquid
royalty free 3d model fighter z for download as on turbosquid: 3d models for games, architecture, videos. (1292563)
turbosquid
$9
Pen Z
...pen z
turbosquid
free 3d model pen z for download as obj on turbosquid: 3d models for games, architecture, videos. (1686775)
turbosquid
free
z chair
...z chair
turbosquid
free 3d model z chair for download as max on turbosquid: 3d models for games, architecture, videos. (1410230)
turbosquid
$5
Letter Z
...urbosquid
royalty free 3d model letter z for download as max on turbosquid: 3d models for games, architecture, videos. (1408540)
Required
turbosquid
$5
Snow chains required
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Made in 3d max 2015. All textures and materials required for rendering are in the archive. The model
...r rendering are in the archive. the model for download as max on turbosquid: 3d models for games, architecture, videos. (1697928)
3d_export
free
cold coffee
...cold coffee 3dexport cold coffee can. any required modifications will be done at...
3d_export
free
Game console
...game console
3dexport
this is a model of a game console that does not require any plug-ins.
3d_export
$5
plummer block
...model of plummer block assembly where seven parts are required to assemble...
3ddd
$1
white table (wood)
...white table (wood) 3ddd обеденный tension mod required fbx and obj included high...
3ddd
$1
Fine Art Lamps 420840 Portobello
...portobello 3ddd fine art lamps no third party plugin required ...
3d_export
$7
kitchenware
...kitchen utensils includes all small electrical appliances that are required for interior...
3d_export
$5
star ball
...sizes. small, medium and original size. adhesive may be required ...
3d_export
$5
shock absorber
...absorber can also provide .stp or .iges format if required ...
Maker
3d_ocean
$17
Coffee Maker
...coffee maker
3docean
breakfast coffee drip electric maker morning
detailed coffee maker and a plug.
3ddd
$1
coffee maker
...coffee maker
3ddd
кофемашина
coffee maker
3d_export
$10
chapati maker
...chapati maker
3dexport
it is a indian traditional chapati maker
archibase_planet
free
Coffee maker
...aker
archibase planet
percolator coffee-machine coffee maker
coffee maker - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Coffee maker
...aker
archibase planet
percolator coffee-machine coffee maker
coffee maker - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Coffee maker
...aker
archibase planet
percolator coffee-machine coffee maker
coffee maker - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Сoffee maker
...er
archibase planet
coffee maker percolator coffee-machine
сoffee maker n020112 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Coffee maker
...aker
archibase planet
coffee maker percolator coffee-machine
coffee maker - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3ddd
$1
Juice Maker
...juice maker
3ddd
соковыжималка
fully detailed kenwood juice maker
archibase_planet
free
Coffee maker
...hibase planet
coffee maker percolator coffee-machine
coffee maker n140611 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
Parts
3d_export
$5
Parts
...parts
3dexport
parts
3d_export
$5
Part
...part
3dexport
part
3d_export
$5
Part
...part
3dexport
machine part
3d_export
$65
Part
...part
3dexport
simple rendering of the scene file
3d_export
$65
Part
...part
3dexport
simple rendering of the scene file
3d_export
$30
fan part
...fan part
3dexport
this is a part of fan of pedastal
3d_export
$10
machine parts
...machine parts
3dexport
3d part modeling work ,contact for 3d work
turbosquid
$59
Mechanical Part
...id
royalty free 3d model mechanical part for download as c4d on turbosquid: 3d models for games, architecture, videos. (1410833)
turbosquid
$17
Road parts
...bosquid
royalty free 3d model road parts for download as 3ds on turbosquid: 3d models for games, architecture, videos. (1192967)
turbosquid
$9
Cutter Parts
...squid
royalty free 3d model cutter parts for download as stl on turbosquid: 3d models for games, architecture, videos. (1220010)
All
turbosquid
$20
all
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
all
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
design_connected
$29
All-Two
...all-two
designconnected
bonaldo all-two computer generated 3d model. designed by bicego, sergio.
design_connected
$29
All-One
...all-one
designconnected
bonaldo all-one computer generated 3d model. designed by bicego, sergio.
design_connected
$16
Holly All
...holly all
designconnected
serralunga holly all computer generated 3d model. designed by starck, philippe.
3d_export
$15
all terrain
...all terrain
3dexport
turbosquid
$29
Holly All
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$19
Fireplace (All)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$19
Fireplace (All)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$19
Fireplace (All)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.