Thingiverse
VX7R Radio holder by Kb9vjq
by Thingiverse
Last crawled date: 3 years ago
I use this to hold my vx7r radio to my pfd when i go sailing .the radio is held secure in the holder and can be inserted without pushing the button but it is nesacary to push the button to remove the radio from the holster the sliding latch requires the installation of 2 small hardware store acquired springs to stay closed,there is room to connect three springs but this was too much pressure on the button.Just use two springs. The springs connect between a brass bolt 1/8 inch in diameter that passes threw the sliding latch and hook onto two of the three small studs that stick up from the slide near a bolt hole. The main holder body is PEGT the slide is bridge Nylon and the latch was abs . If i have to do it over again I would make the latch nylon too . The hook on the latch over hangs a bit and is hard to print but it can be filled smooth when cool and should still keep the radio locked in place . My pfd is inflatable the back plate is large smooth surface to prevent puncturing the pfd, also having such a large backing plate inside the pfd helps keep the antenna on the radio in close to you so its not hooking ropes and lines and things .
Similar models
grabcad
free
3'' Stainless Steel Latch Bolt B203
...s pushed closed, the angled edge of the latch bolt engages with the lip of the strike plate; a spring allows the bolt to retract.
thingiverse
free
Anet A8 v2 Button Trim by AZDawg
...push them. the trim just pushes on over the buttons.
for version 1 with larger clearance:http://www.thingiverse.com/thing:1430125
grabcad
free
"Slide" in Holder for Edifier Remote
...r be bolted on with two m4 screws or has three cutouts on the back to secure it with 19mm wide 21mm thick double sided tesa tape.
grabcad
free
Arrow in the key
...eps, this will improve the precision in the positioning of the plates.
thank you for allowing me to participate in the challenge.
thingiverse
free
Backing Plates for a Skateboard Holder by crkochan
...lower set of wheels to rest on.
note: the plates are twelve inches wide, so a large volume printer is required for this design.
3dwarehouse
free
Wacom Intuos Pen Holder with Kensington Lock Hook
...cket and turn back again to normal position - the holder is now locked in place. and your pen has the new place too. have fun! :)
thingiverse
free
MyFlyDream AAT quick release plate by iPeel
...rx to the back of the antenna, a larger and much larger plate for when you want to stick the rx to the plate and not the antenna.
grabcad
free
Small Spring Bolt Latch
...small spring bolt latch
grabcad
spring bolt latch 6mm dia.
thingiverse
free
E-track holder by 110yawaworth
...o keep them organized.
i couldn't make it large enough so they would latch in normally without having issues keeping them in.
thingiverse
free
Tool Holder Base by etrohn
...s two sd cards, my spring loaded needle nose, hex wrenches and a staple puller (great for getting finished parts off of the hbp)
Kb9Vjq
thingiverse
free
shower curtan rod hanger by Kb9vjq
...shower curtan rod hanger by kb9vjq
thingiverse
shower curtain rod diameter is about 1 inch or 24.5mm
thingiverse
free
Steaming light by Kb9vjq
...wires as the anchor light at the top of the mast . so all i have to do is turn the plug around to select anchor or steaming light
Radio
archibase_planet
free
Radio
...radio
archibase planet
radio
radio - 3d model for interior 3d visualization.
archibase_planet
free
Radio
...radio
archibase planet
radio
radio - 3d model for interior 3d visualization.
3d_export
$10
radio
...radio
3dexport
radio 3d, ojb
archibase_planet
free
Radio
...radio
archibase planet
radio set wireless receiver wireless set
radio 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Radio
...radio
archibase planet
radio set wireless receiver wireless set
radio 7 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Radio
...radio
archibase planet
radio set wireless receiver wireless set
radio 10 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_ocean
$9
Vintage Radio
...vintage radio
3docean
old radio radio set vintage
this is a vintage radio modeled to help in interior design arrangements.
3d_ocean
$8
Radio Branu
...radio branu
3docean
detail radio vintage
vintage radio with detail
3d_export
$5
radio
...radio
3dexport
turbosquid
$25
Radio
...o
turbosquid
royalty free 3d model radio for download as max on turbosquid: 3d models for games, architecture, videos. (1203794)
Holder
archibase_planet
free
Holder
...holder
archibase planet
holder toilet paper holder
holder paper n070712 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...e planet
holder rack toilet paper holder
holder toilet roll n240715 - 3d model (*.gsm+*.3ds+*.max) for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
pen holder support prop
pen holder - 3d model for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
pole post holder
сhurch cross pole holder - 3d model for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
holder bathroom ware
shower holder - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...oilet paper holder
holder paper devon&devon; time black n241113 - 3d model (*.gsm+*.3ds+*.max) for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
holder hanger hanger for towel
holder 7 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
holder hanger hanger for towel
holder 3 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
holder towel rack towel-horse
holder - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...lder
archibase planet
holder hanger hanger for towel
holder towel n250912 - 3d model (*.gsm+*.3ds) for interior 3d visualization.