Thingiverse
Vinyl Vacuum by jdebriyn
by Thingiverse
Last crawled date: 3 years, 2 months ago
This is a vinyl record vacuuming device that allows you to clean records using a small "Shop Vac" size hose.
I place two cover plate (label protectors) on the record and then apply cleaning solution using a soft and fine bristled paint brush. Then place the wet side down and turn on the vacuum. Spin by hand 5-6 times then turn off the vacuum. As the vacuum spins down, keep rotating and lift.
Note that even with the adjuster set 'open,' there may be a lot of suction force. I place a clean microfiber cloth between the device and the the record to prevent scratching the record.
The top and base are held together with M3 x 5mm x 5mm knurled brass threaded inserts (cheap on eBay**) melted into the base and M3 screws (also from eBay).
The label protector (print 2) uses the o-rings from a standard "Culligan" brand replacement o-ring pack for their RO/DI filters, model OR-34A, widely available at hardware stores. Note that there are two sizes, but can be interchanged.
** I ordered about a hundred of these from a seller in China a few years back. I cannot locate the same seller, but my inserts have parallel knurling (not twisted). The measure 5mm x 5mm at the thickest points and slightly less than 4mm where there is no knurling. They should be less than $5 for 100 shipped to US.
I place two cover plate (label protectors) on the record and then apply cleaning solution using a soft and fine bristled paint brush. Then place the wet side down and turn on the vacuum. Spin by hand 5-6 times then turn off the vacuum. As the vacuum spins down, keep rotating and lift.
Note that even with the adjuster set 'open,' there may be a lot of suction force. I place a clean microfiber cloth between the device and the the record to prevent scratching the record.
The top and base are held together with M3 x 5mm x 5mm knurled brass threaded inserts (cheap on eBay**) melted into the base and M3 screws (also from eBay).
The label protector (print 2) uses the o-rings from a standard "Culligan" brand replacement o-ring pack for their RO/DI filters, model OR-34A, widely available at hardware stores. Note that there are two sizes, but can be interchanged.
** I ordered about a hundred of these from a seller in China a few years back. I cannot locate the same seller, but my inserts have parallel knurling (not twisted). The measure 5mm x 5mm at the thickest points and slightly less than 4mm where there is no knurling. They should be less than $5 for 100 shipped to US.
Similar models
thingiverse
free
Wet/Dry vacuum attachment for cleaning Vinyl Records by Plasticyst
...robably make revisions in the future for vacuum compatibility, pressure adjustments, ability to clean 7 and 10 inch records, etc.
thingiverse
free
LP vinyl 12 inch record label saver washer by ksdj55
...ry while cleaning in a kitchen sink.
including 2 tpu o-ring pattern (choose one).
use 1x m6x35 or longer hexagonal screw and nut.
thingiverse
free
ANYCUBIC 3D MKS MOSFET Mount
...ixed it to my wanhao duplicator i3 with epoxy.
parts list:
4x - m3 x 4mm x 5mm knurled brass threaded insert
4x - m3 x 10mm screw
thingiverse
free
M3 Knurled Knob by xjuls
...m3 knurled knob by xjuls
thingiverse
m3 knurled knobs - m3 - 4mm x 5mm
grabcad
free
Assembly of M3 X 3-12 mm Length, Brass Knurled Inserts
...ht deviations from vendor to vendor in knurled profile and outer diameter that gets inserted into a hole.
https://bit.ly/3rsha92
thingiverse
free
8DJ by mageli
... parts
• insert a vinyl record (parts sized for small records, to be resized for large records)
• screw the parts
• and spin it !
thingiverse
free
M3 Knurled Nut Gripper by robthomson
...e
deisned to use an m3 brass insert
10mm height
5mm width
you will need to push fit the brass insert in with a hot solder iron!
thingiverse
free
GhostlySheen Coaster by Nebby85
...lace to put their
drink and if you're just listening to an old record then here's a place to
put the red wine.
enjoy :)
thingiverse
free
Vinyl turntable dust cover by Arkaivos
...e is not being used, to prevent dust falling on the surface that makes contact with the record.
the cover has a diameter of 30cm.
thingiverse
free
insert test by LPHconus
...ade for
m2 brass-knurl
m2.5 brass-knurl
m3 brass-knurl
m4 brass-knurl
you are able to pay those form ebay: http://ebay.to/2g2m498
Jdebriyn
thingiverse
free
NanoCube 6 Aquarium Overflow by jdebriyn
...nanocube 6 aquarium overflow by jdebriyn
thingiverse
simply overflow for small nanocube 6 gal aquarium
thingiverse
free
Prusa mk2 Z-axis Camera Holder by jdebriyn
...fits the y-idler perfectly if you print a spare. it fits the one that came with my mk2 almost perfectly. integrated cable holder.
thingiverse
free
Aukey DR02 Dashcam GoPro Mount for Tacoma
...thingiverse probably fits other aukey dashcams, too. i took jdebriyn#39;s design and moved the tab on the top to...
thingiverse
free
XZ-axis Prusa i3 MK2S clipped camera holder by Archicens
...for the lower position. this clip is inspired by jdebriyn#39;s prusa mk2 z-axis camera holder. because the clip didn't...
Vinyl
archibase_planet
free
Vinyl record
...planet
vinyl record gramophone record vinyl disk
disc vinyl music n090414 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
Vinyl 3D Model
...vinyl 3d model
3dexport
vinyl model
vinyl 3d model dzya 27264 3dexport
3d_export
$7
crosley vinyl player
...crosley vinyl player
3dexport
vinyl crosley player with headphones.
turbosquid
free
Vinyl Record
...rd
turbosquid
free 3d model vinyl record for download as fbx on turbosquid: 3d models for games, architecture, videos. (1298466)
turbosquid
free
vinyl disc
...
free 3d model vinyl disc for download as blend, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1608654)
turbosquid
$15
Vinyl Table
...3d model vinyl table for download as blend, 3ds, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1633839)
3d_ocean
$4
Vinyl Record
...album artwork or adding to a music scene. each layer and material has been named clearly. i have included an .obj file for any...
turbosquid
$10
Vinyl Record
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$4
Vinyl Record
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$4
LP vinyl + cover
... textures (vinyl label & cover label) are in .psd format (included in tex folder) you can personalize it like you want enjoy
Vacuum
archibase_planet
free
Vacuum cleaner
...cuum cleaner vacuum hoover exhauster
vacuum cleaner stefano galli n250213 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$12
vacuum cleaner
...vacuum cleaner
3dexport
vacuum cleaner fo houses
3ddd
$1
Vacuum Cleaner
...vacuum cleaner
3ddd
пылесос
vacuum cleaner + obj + textures
3d_export
$170
VACUUM BOWL
...vacuum bowl
3dexport
3d_export
$5
Bracket vacuum 3D Model
...bracket vacuum 3d model
3dexport
vacuum
bracket vacuum 3d model bkl1989 63086 3dexport
3d_export
$50
Vacuum Cleaner 3D Model
...vacuum cleaner 3d model
3dexport
vacuum cleaner
vacuum cleaner 3d model kaxa3d 12593 3dexport
3d_export
$5
vacuum cleaner
...vacuum cleaner
3dexport
diameter 32 mm
archive3d
free
Vacuum cleaner 3D Model
...er
vacuum cleaner stefano galli n250213 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$69
vacuum furnaces
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$59
Vacuum Italian
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.