Thingiverse
USB Dongelier by sdkks
by Thingiverse
Last crawled date: 3 years, 3 months ago
USB Dongle holder for sticks, memory cards, wireless receivers etc. Holds up to 15 devices.
It can also be mounted on wall with double sided tape to hang cables on bottom line and stick USB devices on upper rows vice versa.
Recommend snug fit for wall mount, loose fit for desk use. If you are not sure, I recommend the loose fit.
Tolerances for fit should be sufficient, I tested with 3 different prints. Can scale up/down %1 if it's too loose or too tight for your dongles. I tested with all USB devices I could find. All metallic body Samsung Flash Stick had trouble fitting, which was over USB specs (max should be 0.05 as per specs but Samsung stick was way over it.)
Original design can be found here on Tinkercard.
I tested fitting with smaller version of the prints without printing the whole thing, i.e. a single cap, which is also included. It can be used as protective USB cap for your devies or you can fit/glue it into places to hold dongles temporarily. (See my PS4 Pro photo, it's press fit into gap. I unplug wireless headphone receiver when I want to use TV speakers for local multiplayer)
It can also be mounted on wall with double sided tape to hang cables on bottom line and stick USB devices on upper rows vice versa.
Recommend snug fit for wall mount, loose fit for desk use. If you are not sure, I recommend the loose fit.
Tolerances for fit should be sufficient, I tested with 3 different prints. Can scale up/down %1 if it's too loose or too tight for your dongles. I tested with all USB devices I could find. All metallic body Samsung Flash Stick had trouble fitting, which was over USB specs (max should be 0.05 as per specs but Samsung stick was way over it.)
Original design can be found here on Tinkercard.
I tested fitting with smaller version of the prints without printing the whole thing, i.e. a single cap, which is also included. It can be used as protective USB cap for your devies or you can fit/glue it into places to hold dongles temporarily. (See my PS4 Pro photo, it's press fit into gap. I unplug wireless headphone receiver when I want to use TV speakers for local multiplayer)
Similar models
thingiverse
free
Wall Mounted Headset / Headphone by Hu9o
... the load and prevents indentation of the headband foam.
it also has a small storage area for, wireless dongle or mic-foam piece.
thingiverse
free
Wireless Headset Wall mount by CriscoJoe37
...ll mount by criscojoe37
thingiverse
this is a wall mount for wireless headsets, it has a cutout for holding the wireless dongle.
thingiverse
free
Simple USB Dongle holder by byproduct
...rm without being too snug to fit. i intend to use double sided tape to attach it to the side of my header when i am not using it.
thingiverse
free
Samsung Wireless charging stand (Portrait position) by Intashu
...fill so it can hold up the phone without sliding around and/or breaking. anti-slip pads on the bottom would be a great idea also!
thingiverse
free
USB Receiver Holder by calvertdw
...tdw
thingiverse
a little mount for holding a usb cable. i use it to hold my logitech g930 wireless adapter up to get good range.
thingiverse
free
Samsung S7 dock for 60mm wireless charging pad by Pillage_then_burn
...msung s series phones to be used with a 60mm diam wireless charger with usb.
prints without supports
fit is a bit loose for an s7
grabcad
free
Wireless Mouse
...se
grabcad
a wireless usb mouse uses a usb device that can be plugged into one of your system's usb ports to receive signals
thingiverse
free
Samsung Flash Drive FIT Cap by jolau
...samsung flash drive fit cap by jolau
thingiverse
cap for the samsung flash drive fit usb stick.
thingiverse
free
Steam Controller Wall mount by strelly
... screwed into the wall or affixed using a double sided tape.
there is a slot to hold the usb dongle (two locations to place this)
thingiverse
free
K830 USB holder by Diesel_Dummy
...r clips on the back and holds the dongle. print two and you have a flash drive holder too.....and your keyboard won't wobble.
Sdkks
thingiverse
free
Small Turntable with Printed Bearing featuring lube ports by sdkks
...d item in action
how to unlock and lube the bearing
use raft only for bearing if your squish is too wide aka elephant's foot.
thingiverse
free
Large Turntable with printed bearing by sdkks
...on
assembled whole unit
ps: i'm trying to link remix links but searching for the item by id or name fails, returns 0 results.
thingiverse
free
Tinkerton the simple, economical stand by sdkks
...m3 or smaller screws if you want to fasten the base to a shelf incase shelf table etc has free play. (like my ikea mesh shelves.)
thingiverse
free
608 Simple Bearing with lubrication port by sdkks
...ion) due to squish seizing the first layer.
youtube video which shows a simple use case for spool holder/roller
made in tinkercad
thingiverse
free
Ender DD Direct Drive Filament Runout Sensor Mount by sdkks
...ner print to hang the slack of the cable however it's not necessary if you will use other means to guide the wires of sensor.
thingiverse
free
Ender 3 v2 Light bar adapter for Maglehult ikea light bar by littledevil
...adapter was a mix of a sensor adapter by "sdkksquot; and the ikea light bar adapter, for a different...
thingiverse
free
Sapphire Plus CoreXY 4020 Profile RaspBerry Pi 4 RPI4 GeekPi Case Mount by sdkks
...also be used as legs. i flipped them and put them on top so i don't have to insert it as i don't have the tooling for it.
Usb
3d_ocean
$3
USB Thumbdrive
...usb thumbdrive
3docean
thumbdrive usb usb drive usb stick
this is a swivel type usb thumb drive.
3d_ocean
$5
Usb Stick
...usb stick
3docean
flash stick usb usb memory usb stick
usb stick created using 3ds max 2015 and rendered on mental ray.
3ddd
$1
USB cable
... кабель , провод
высокополигональные модели кабелей usb.
3d_ocean
$5
USB Stick
...usb stick
3docean
32gb computer memory plug plugin protection usb usb stick
an usb stick with built-in plug protection
3d_ocean
$6
USB Stick
...tick
3docean
32 gb flash ram gigabyte memory metal nand plug ram stick usb usb 3 usb stick
usb stick with texture and normal map.
turbosquid
$5
USBS
...bs
turbosquid
royalty free 3d model usbs for download as max on turbosquid: 3d models for games, architecture, videos. (1466594)
3d_export
$5
usb flash
...usb flash
3dexport
usb flash
3d_export
free
usb flash
...usb flash
3dexport
usb flash
3d_export
free
usb flash
...usb flash
3dexport
usb flash driver
3ddd
$1
usb
...usb
3ddd
флешка
флешка