Thingiverse
Ursa (bear) - Fully printable Monster Truck by tahustvedt
by Thingiverse
Last crawled date: 3 years, 1 month ago
Fully printable monster truck with four link suspension and four wheel drive and steering with three differentials. I wanted a monster truck that actually looks like a monster truck, and not a truggy with large wheels.
If you want to support my work you can use any of the Ebay or Banggood-links below before making purchases.
Videos:https://youtu.be/mVA5D9kVJJshttps://youtu.be/9wNiFeGisZwhttps://youtu.be/AO-AkMLZNDAhttps://youtu.be/2taKQ4_r750https://youtu.be/wBgna8vqM7Ahttps://youtu.be/CZGQl6PWfFMhttps://youtu.be/f0mxxbsc6S8https://youtu.be/uLqwb3P9NfMhttps://youtu.be/4p0nPPbaKH8https://youtu.be/VDS8F1Fntychttps://youtu.be/_6eOmHweF8khttps://youtu.be/253u5Jxf34w
Extra accessories:
Mega truck wheels for it: https://cults3d.com/en/3d-model/various/mega-truck-tires-for-the-ursa-1-12-scale-monster-truck
Van body: https://cults3d.com/en/3d-model/various/80-s-van-body-for-the-ursa-monster-truck
Assembly notes:
-Tighten the suspension arm clamps around the axle balls until they allow some movement, but not too tight. The ball joint needs to be able to move with suspension travel.
-The axle gearbox halves may have some uglyness in the top where the 7mm bearing goes. Just remove any excess plastic threads and stuff the bearing in there. I've done it to many units without failure. I might improve this part of the design later on.
-Apply a small amount of grease to the inside of all drive joints so that the plastic knuckles don't melt from friction. I use cheap bicycle lithium grease. Any grease will do. The drive shafts and drive knuckles can be a little tight. They will bed in. Adding 2x13 mm steel pins throuhg the holes in the ends greatly improve their longevity and torquen handling.
-Apply grease to all gears. This prevents melting and keeps them working for long. I made closed gearboxes so that they could be greased without too much contamination. I use cheap bicycle lithium grease. Any grease will do.
-The gears will bed in if they feel rough in the beginning. Most of the gears seem to be very strong and show no signs of overloading. The differential bevel gears can break with very rough use if they are made from PLA. I eventually printed them from Taulman 910 nylon, which survived my torture tests.
-The smallest differential gears need small shafts to hold them in place. Make these short pieces from 1,8-2mm steel rods to fit in the diff gear.
-Ball bearings can be a tight fit, depending on how accurate your printer prints. The holes are designed slightly oversize. Just press them in there or carefully hammer with something that ensures the force hits the outside race. :)
-The lower links flex when the car rolls. This is by design and works well and acts as an anti roll bar function.
-Some parts have alternative parts so that the builder can create variations and change the look of the truck. Parts marked SWB are short wheelbase options, MWB are medium wheelbase options, and LWB are long wheelbase options. LWB looks more modern while SWB looks old school. Mix and match front and back as you like.
-The screws all thread into the plastic parts without any metal nuts. It may be difficult to screw them in the first time.
-Though the hardware list calls for machine screws, similarly sized self tapping screws will work fine in most cases. The exception being where the part is supposed to pivot on the screw, like the spindles and suspension link hinges. The length can also be different than the recommended in many cases as the holes are usually much deeper than necessary.
-The rear steering servo needs to be reversed. If it can not be reversed in the radio the longer servo link can be used instead by connecting to the top servo arm instead of the bottom.
-The diff lock gear is not recommended for jumps and high speed bashing because it increases the load on the whole drive train.
-Some illustrations show an older diff variant with five little sattelite gears while the newer stronger version has four gears. Otherwise they are the same.
Required hardware:
-Minimum 2 channel transmitter and receiver. Cheap:This is better because you can mix the steering in programming
-540 or 380 motor and ESC. The prototype uses a 21t GoolRC brushed motor for overload testing. I recommend a minimum of 35T
The best ESC for it is the Hobbywing Quicrun 80A "Crawler Brushed" ESC which can be set up to run with reduced brake and reduced punch which extends the gear life considerably: )
-Metal gear servos. Maximum 23mm body length. Corona 843mg is HIGHLY recommendedThese also work well, but are very noticeably weaker
-Six cell Sub-C ni-mh battery or 2S hard body lipo (https://www.banggood.com/Giant-Power-7_4V-6000mAh-2S-65C-Lipo-Battery-T-Plug-Hardcase-Pack-p-1080409.html?p=HD240528697332015103&custlinkid=822350), or saddle pack for the newest saddle frame (recommended). Any small 2s lipo that will fit will work. It's a low power car.
-The springs are made from regular road bicycle tubes. Cut them as wide as you need to get the necessary tension. The butyl is very durable and won't rot. I used one of my old punctured tubes. I also use these rubber bands to hold the battery in place
-In addition to the printable body you can use other bodies. I ordered this body which fits well
-Four monster tires. Printing the printable tires is possible but is probably more expensive than buying them, and less flexible by far. I use the chevron version of the two in the following links
-7 3mmx19mm carbon fiber, steel or brass shafts for the diffs and live axle gearboxes
-2mm steel rod for the pin drive shafts and diff bevel gears
-4 to 8 3x7x3 ball bearings
-20 12x18x4 ball bearings. https://rover.ebay.com/rover/1/711-53200-19255-0/1?ff3=4&toolid=11800&pub=5575353675&campid=5338226872&mpre=https%3A%2F%2Fwww.ebay.com%2Fitm%2F5-10-20-pcs-Thin-wall-Ball-Bearing-6000-2RS-To-6904-2RS-Rubber-Shielded-Bearings%2F302178407515
-44 M2x8 screws - differential gearbox assembly, upper four link clamp and steering link assembly. 24 of them for assembly of the two piece wheels.
-2 M2.5x22 screws - For mounting a 380 sie motor.
-22 M3x8 screws - Main frame assembly and steering spindle assembly.
-8 M3x12 screws - Lower suspension link and upper rubber band posts.
-6 M3x22 screws (M3x24 can also be used) - 540 Motor mount and lower rubber band posts.
-4 M4x20 screws - For the wheels.
-An assortment of screws is recommended.
Body01.stl - Front of Datsun Big Bear body.
Body02.stl - Middle of Datsun Big Bear body.
Body02-windows.stl - Middle of Datsun Big Bear body with window cutouts.
Body03.stl - Rear of Datsun Big Bear body.
Body04.stl - Body posts for Datsun Big Bear body.
Body05.stl - Front of Datsun Big Bear body.
Mirror01.stl - Mirrors for the Datsun Big Bear body.
Bodypost01.STL - Shortest body post for lexan bodies.
Bodypost02.STL - Medium body post for lexan bodies.
Bodypost03.STL - Long body post for lexan bodies.
Bodypost04.STL - Extra long body post for lexan bodies.
Bodypost05.STL - Strengthened medium body post for lexan bodies.
Bodypost05.STL - Strengthened extra long body post for lexan bodies.
CGB-380.STL - Central gearbox and pinion for 380 size motors.
CGB-540.STL - Central gearbox and pinion for 540 size motors.
CGB-gears.STL - Central gearbox gears.
Difflock02.STL - Optional locking "gears" for all diffs.
GB03.stl - Live axle gearbox housing. Front and rear are the same.
GB03-axles.stl - Long internal axles.
GB03-gears.STL - Live axle gearbox gears.
GB03-input.stl - Input coupling and bevel gear for the live axle gearbox.
GB03-input-onepiece.stl - Input coupling and bevel gear in one piece. Pause the print and insrt bearings before the gear portion.
Spindle01.STL - Steering spindles for the outer ends of the live axles.
Frame01.stl - Basic main frame sides.
Frame01-sidemount - Main frame sides with saddle pack mounts on the sides for lower CG.
Frame01-split01 and 02.stl - Basic main frame sides, split up to fit tiny printers.
Frame02.stl - Front and rear frame pieces. "Triangle" version.
Frame03.stl - Front and rear frame pieces. "Tall cage" version
Frame04.stl - Front and rear frame pieces. "No cage" version.
Frame05.stl - Front and rear frame pieces. "Low cage" version.
Rollbar02.stl - Rollbar.
Rollbar03.stl - Rollbar with light holders.
Servosaver01.STL - Basic servo saver for installing onto a servo arm or disc.
Servosaver02.STL - Splined servo saver for installing onto a small servo spline.
Servosaver03.STL - Splined servo saver for installing onto a large servo spline.
Steeringlink01.STL - Steering links.
Steeringlink02.STL - Offset steering link in case it's needed to line up, for example when using a servo saver.
Steeringlink03.STL - New and improved steering link with ball linkage to the servo.
Suspension01-SWB.stl - Suspension parts for short wheelbase, type 1.
Suspension01-MWB.stl - Suspension parts for medium wheelbase, type 1.
Suspension01-LWB.stl - Suspension parts for long wheelbase, type 1.
Suspension02-SWB.stl - Suspension parts for short wheelbase, type 2.
Suspension02-MWB.stl - Suspension parts for medium wheelbase, type 2.
Suspension02-LWB.stl - Suspension parts for long wheelbase, type 2.
Suspension03.stl - Lower suspension bushing and rubber band flanges for the spring assembly.
Wheel01.stl - Monster truck wheel. Narrow type. Recommended for bought tires.
Wheel02.stl - Monster truck wheel. Wide type. Fits wide printed tires.
TireLeft.STL - Wide printable left tire. 83 mm width. Fits wide wheel.
TireRight.STL - Wide printable right tire. 83 mm width.Fits wide wheel.
TireLeft-narrow.STL - Narrow printable left tire. 73 mm width. Fits narrow wheel.
TireRight-narrow.STL - Narrow printable right tire. 73 mm width. Fits narrow wheel.
If you want to support my work you can use any of the Ebay or Banggood-links below before making purchases.
Videos:https://youtu.be/mVA5D9kVJJshttps://youtu.be/9wNiFeGisZwhttps://youtu.be/AO-AkMLZNDAhttps://youtu.be/2taKQ4_r750https://youtu.be/wBgna8vqM7Ahttps://youtu.be/CZGQl6PWfFMhttps://youtu.be/f0mxxbsc6S8https://youtu.be/uLqwb3P9NfMhttps://youtu.be/4p0nPPbaKH8https://youtu.be/VDS8F1Fntychttps://youtu.be/_6eOmHweF8khttps://youtu.be/253u5Jxf34w
Extra accessories:
Mega truck wheels for it: https://cults3d.com/en/3d-model/various/mega-truck-tires-for-the-ursa-1-12-scale-monster-truck
Van body: https://cults3d.com/en/3d-model/various/80-s-van-body-for-the-ursa-monster-truck
Assembly notes:
-Tighten the suspension arm clamps around the axle balls until they allow some movement, but not too tight. The ball joint needs to be able to move with suspension travel.
-The axle gearbox halves may have some uglyness in the top where the 7mm bearing goes. Just remove any excess plastic threads and stuff the bearing in there. I've done it to many units without failure. I might improve this part of the design later on.
-Apply a small amount of grease to the inside of all drive joints so that the plastic knuckles don't melt from friction. I use cheap bicycle lithium grease. Any grease will do. The drive shafts and drive knuckles can be a little tight. They will bed in. Adding 2x13 mm steel pins throuhg the holes in the ends greatly improve their longevity and torquen handling.
-Apply grease to all gears. This prevents melting and keeps them working for long. I made closed gearboxes so that they could be greased without too much contamination. I use cheap bicycle lithium grease. Any grease will do.
-The gears will bed in if they feel rough in the beginning. Most of the gears seem to be very strong and show no signs of overloading. The differential bevel gears can break with very rough use if they are made from PLA. I eventually printed them from Taulman 910 nylon, which survived my torture tests.
-The smallest differential gears need small shafts to hold them in place. Make these short pieces from 1,8-2mm steel rods to fit in the diff gear.
-Ball bearings can be a tight fit, depending on how accurate your printer prints. The holes are designed slightly oversize. Just press them in there or carefully hammer with something that ensures the force hits the outside race. :)
-The lower links flex when the car rolls. This is by design and works well and acts as an anti roll bar function.
-Some parts have alternative parts so that the builder can create variations and change the look of the truck. Parts marked SWB are short wheelbase options, MWB are medium wheelbase options, and LWB are long wheelbase options. LWB looks more modern while SWB looks old school. Mix and match front and back as you like.
-The screws all thread into the plastic parts without any metal nuts. It may be difficult to screw them in the first time.
-Though the hardware list calls for machine screws, similarly sized self tapping screws will work fine in most cases. The exception being where the part is supposed to pivot on the screw, like the spindles and suspension link hinges. The length can also be different than the recommended in many cases as the holes are usually much deeper than necessary.
-The rear steering servo needs to be reversed. If it can not be reversed in the radio the longer servo link can be used instead by connecting to the top servo arm instead of the bottom.
-The diff lock gear is not recommended for jumps and high speed bashing because it increases the load on the whole drive train.
-Some illustrations show an older diff variant with five little sattelite gears while the newer stronger version has four gears. Otherwise they are the same.
Required hardware:
-Minimum 2 channel transmitter and receiver. Cheap:This is better because you can mix the steering in programming
-540 or 380 motor and ESC. The prototype uses a 21t GoolRC brushed motor for overload testing. I recommend a minimum of 35T
The best ESC for it is the Hobbywing Quicrun 80A "Crawler Brushed" ESC which can be set up to run with reduced brake and reduced punch which extends the gear life considerably: )
-Metal gear servos. Maximum 23mm body length. Corona 843mg is HIGHLY recommendedThese also work well, but are very noticeably weaker
-Six cell Sub-C ni-mh battery or 2S hard body lipo (https://www.banggood.com/Giant-Power-7_4V-6000mAh-2S-65C-Lipo-Battery-T-Plug-Hardcase-Pack-p-1080409.html?p=HD240528697332015103&custlinkid=822350), or saddle pack for the newest saddle frame (recommended). Any small 2s lipo that will fit will work. It's a low power car.
-The springs are made from regular road bicycle tubes. Cut them as wide as you need to get the necessary tension. The butyl is very durable and won't rot. I used one of my old punctured tubes. I also use these rubber bands to hold the battery in place
-In addition to the printable body you can use other bodies. I ordered this body which fits well
-Four monster tires. Printing the printable tires is possible but is probably more expensive than buying them, and less flexible by far. I use the chevron version of the two in the following links
-7 3mmx19mm carbon fiber, steel or brass shafts for the diffs and live axle gearboxes
-2mm steel rod for the pin drive shafts and diff bevel gears
-4 to 8 3x7x3 ball bearings
-20 12x18x4 ball bearings. https://rover.ebay.com/rover/1/711-53200-19255-0/1?ff3=4&toolid=11800&pub=5575353675&campid=5338226872&mpre=https%3A%2F%2Fwww.ebay.com%2Fitm%2F5-10-20-pcs-Thin-wall-Ball-Bearing-6000-2RS-To-6904-2RS-Rubber-Shielded-Bearings%2F302178407515
-44 M2x8 screws - differential gearbox assembly, upper four link clamp and steering link assembly. 24 of them for assembly of the two piece wheels.
-2 M2.5x22 screws - For mounting a 380 sie motor.
-22 M3x8 screws - Main frame assembly and steering spindle assembly.
-8 M3x12 screws - Lower suspension link and upper rubber band posts.
-6 M3x22 screws (M3x24 can also be used) - 540 Motor mount and lower rubber band posts.
-4 M4x20 screws - For the wheels.
-An assortment of screws is recommended.
Body01.stl - Front of Datsun Big Bear body.
Body02.stl - Middle of Datsun Big Bear body.
Body02-windows.stl - Middle of Datsun Big Bear body with window cutouts.
Body03.stl - Rear of Datsun Big Bear body.
Body04.stl - Body posts for Datsun Big Bear body.
Body05.stl - Front of Datsun Big Bear body.
Mirror01.stl - Mirrors for the Datsun Big Bear body.
Bodypost01.STL - Shortest body post for lexan bodies.
Bodypost02.STL - Medium body post for lexan bodies.
Bodypost03.STL - Long body post for lexan bodies.
Bodypost04.STL - Extra long body post for lexan bodies.
Bodypost05.STL - Strengthened medium body post for lexan bodies.
Bodypost05.STL - Strengthened extra long body post for lexan bodies.
CGB-380.STL - Central gearbox and pinion for 380 size motors.
CGB-540.STL - Central gearbox and pinion for 540 size motors.
CGB-gears.STL - Central gearbox gears.
Difflock02.STL - Optional locking "gears" for all diffs.
GB03.stl - Live axle gearbox housing. Front and rear are the same.
GB03-axles.stl - Long internal axles.
GB03-gears.STL - Live axle gearbox gears.
GB03-input.stl - Input coupling and bevel gear for the live axle gearbox.
GB03-input-onepiece.stl - Input coupling and bevel gear in one piece. Pause the print and insrt bearings before the gear portion.
Spindle01.STL - Steering spindles for the outer ends of the live axles.
Frame01.stl - Basic main frame sides.
Frame01-sidemount - Main frame sides with saddle pack mounts on the sides for lower CG.
Frame01-split01 and 02.stl - Basic main frame sides, split up to fit tiny printers.
Frame02.stl - Front and rear frame pieces. "Triangle" version.
Frame03.stl - Front and rear frame pieces. "Tall cage" version
Frame04.stl - Front and rear frame pieces. "No cage" version.
Frame05.stl - Front and rear frame pieces. "Low cage" version.
Rollbar02.stl - Rollbar.
Rollbar03.stl - Rollbar with light holders.
Servosaver01.STL - Basic servo saver for installing onto a servo arm or disc.
Servosaver02.STL - Splined servo saver for installing onto a small servo spline.
Servosaver03.STL - Splined servo saver for installing onto a large servo spline.
Steeringlink01.STL - Steering links.
Steeringlink02.STL - Offset steering link in case it's needed to line up, for example when using a servo saver.
Steeringlink03.STL - New and improved steering link with ball linkage to the servo.
Suspension01-SWB.stl - Suspension parts for short wheelbase, type 1.
Suspension01-MWB.stl - Suspension parts for medium wheelbase, type 1.
Suspension01-LWB.stl - Suspension parts for long wheelbase, type 1.
Suspension02-SWB.stl - Suspension parts for short wheelbase, type 2.
Suspension02-MWB.stl - Suspension parts for medium wheelbase, type 2.
Suspension02-LWB.stl - Suspension parts for long wheelbase, type 2.
Suspension03.stl - Lower suspension bushing and rubber band flanges for the spring assembly.
Wheel01.stl - Monster truck wheel. Narrow type. Recommended for bought tires.
Wheel02.stl - Monster truck wheel. Wide type. Fits wide printed tires.
TireLeft.STL - Wide printable left tire. 83 mm width. Fits wide wheel.
TireRight.STL - Wide printable right tire. 83 mm width.Fits wide wheel.
TireLeft-narrow.STL - Narrow printable left tire. 73 mm width. Fits narrow wheel.
TireRight-narrow.STL - Narrow printable right tire. 73 mm width. Fits narrow wheel.
Similar models
cults
free
Fully printable Monster Truck
...time. -though the hardware list calls for machine screws, similary sized self tapping screws will work fine in most...
thingiverse
free
WPL C24 lowrider servo and body mount by skr00zloose
...s.
the shortened axles, suspension trusses, wheels, and tires i've built for this project are also available on thingiverse.
thingiverse
free
simple FWD/4WD front axle for DIY RC truck by Spone
... bevel gear" (https://www.thingiverse.com/thing:1733067)
20.11.2017 update:
servo for steering glued straight to gear cover.
grabcad
free
Tamiya TXT-1 RC Monster Truck
...ing suspension axles, and 4 wheeled steering.
http://grabcad.com/library/short-course-truck-body by http://grabcad.com/matt.perez
thingiverse
free
RC Monster Truck Rockwell Axle Version 3 by gsbinder
...wheel shafts, bearings, and 17mm hubs. all screws are m3.
5/10/2021 - updated files for lower case, suspension, and servo mount.
3dwarehouse
free
truck wheels
...truck wheels
3dwarehouse
truck wheels, everything made by me #axle #brakes #rim #suspension #tire #truck #wheel #wheels
thingiverse
free
Tactic TTX300 steering angle increaser by MasteroFlego
...riginal coarse thread screw.
using the 3x8mm screws, attach the cover.
install original steering wheel with the last 3x5mm screw.
thingiverse
free
Blaze Monster Truck by mb20music
...e axles and wheels.
only the body will need support.
truck is about 120mm long but can of course be scaled up or down if desired.
grabcad
free
Gearbox for ATV with Torsen Differential
...s worm gear and spur gear diff case and the working principle of the worm gear, this differential acts as a locking differential.
grabcad
free
Automatic Grease Routing | Tandem Axle Suspension in Trucks
...ease routing done for tandem axle truck suspension.
this is only for showcasing my skills, not for production process.
thanks.
Tahustvedt
thingiverse
free
Hextronix HXT900 servo by tahustvedt
... hxt900 servo by tahustvedt
thingiverse
accurate model of a hextronix hxt900 servo. made from measurements form an actual servo.
thingiverse
free
540 AND 550 MOTORS. by tahustvedt
...e
540 and 550 motor models to help with design work. the backplate timing isn't right, but all dimensions are very accurate.
thingiverse
free
RC airplane wheel chocks. by tahustvedt
... chocks. by tahustvedt
thingiverse
wheel chocks for rc planes. these fit 114 mm/4,5" wheels. scale up or down as necessary.
thingiverse
free
Lynx Helicopter cookie cutters by tahustvedt
...edt
thingiverse
cookie cutters in the shape of the rnoaf westland lynx mk. 86 helicopter. 01 is 21 cm long and 02 is 28 cm long.
thingiverse
free
Wing for Schumacher CAT XLS by tahustvedt
...le wing for the schumacher cat xls and other vintage cat's. print solid for strength.
catwing02 has integrated mounting lugs.
thingiverse
free
Hitec HS-65HB Mighty Feather servo by tahustvedt
...ghty feather servo by tahustvedt
thingiverse
accurate model of a hitec hs-65hb servo. modeled from measurements of a real servo.
thingiverse
free
Gary the pilot. by tahustvedt
...your slicer to achieve the height you need. i didn't use any support between the head and headset arch and it came out great.
thingiverse
free
Hitec HS-225MG Mighty Mini servo by tahustvedt
...i servo by tahustvedt
thingiverse
an accurate model of the hitec hs-225mg servo modeled using measurements from an actual servo.
thingiverse
free
Skis for RC planes by tahustvedt
...he curved underside with thick ca and then glue the keels. use a spring, rubber band or rubber bumper to hold it level in flight.
thingiverse
free
Wanhao Duplicator i3 fan mount spacers by tahustvedt
...f fans which are mounted to the original mounting bracket on the wanhao duplicator i3 printer.
the spacers are 3mm and 1mm tall.
Ursa
3ddd
$1
Calligaris / Ursa
...o sizes and colours, red or white.
designer: enrico zanollahttp://enricozanolla.com/#236-ursa
manufacturer: calligaris
turbosquid
$10
Ursa Oil Rig
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
thingiverse
free
Ursa by AlexPewPew
...ursa by alexpewpew
thingiverse
ursa in a sweet pose
3d_sky
free
Calligaris / Ursa
...o sizes and colours, red or white.
designer: enrico zanollahttp://enricozanolla.com/#236-ursa
manufacturer: calligaris
thingiverse
free
teddy ursa keychain
...teddy ursa keychain
thingiverse
head of teddy ursa pokemon keychain piece. stl. file.
thingiverse
free
Ursa Minor Xiaoling
...ursa minor xiaoling
thingiverse
try not to fall :)
thingiverse
free
Tiny Ursa Sci fi robot by smight
...tiny ursa sci fi robot by smight
thingiverse
tiny ursa sci fi robot
thingiverse
free
Ursa King Cab Body by Superclodbuster
...tight but you may need to sand them to fit.
2% infill 1 perimeter for body. rollbar 25% infill. designed to print as orientated.
thingiverse
free
Constellation Ursa Major by Jivemat
...stars raise above the silhouette so when it gets to the star layers just pause the print and switch to glow in the dark filament.
thingiverse
free
Ursa Bear shock mounts by zxcvbn
...e
new diff shock mounts for the ursa bear. turned around so the shocks can be removed with out having to remove the hubs/wheels.
Monster
3d_export
$5
monster
...monster
3dexport
very realistic monster
3d_export
free
monster
...monster
3dexport
bloody monster! (looks terrifying)
3d_ocean
$12
Monster
... this code “envatoguest2016” . visit our store high details 3d character model for small monster , useful for animations, movi...
3d_ocean
$15
Monster
...monster
3docean
android game ios java main model monster playdesign
polycount :1118 texture :1024×1024png
3d_ocean
$8
Monster Man
...monster man
3docean
giant monster
monster man software: 3ds max, mental ray.
turbosquid
$60
MONSTER
...turbosquid
royalty free 3d model monster for download as max on turbosquid: 3d models for games, architecture, videos. (1220728)
turbosquid
$60
Monster
...turbosquid
royalty free 3d model monster for download as fbx on turbosquid: 3d models for games, architecture, videos. (1320840)
turbosquid
$19
Monster
...turbosquid
royalty free 3d model monster for download as max on turbosquid: 3d models for games, architecture, videos. (1248452)
turbosquid
$15
Monster
...turbosquid
royalty free 3d model monster for download as ztl on turbosquid: 3d models for games, architecture, videos. (1417804)
turbosquid
$15
Monster
...turbosquid
royalty free 3d model monster for download as max on turbosquid: 3d models for games, architecture, videos. (1293042)
Truck
3d_export
$8
truck
...truck
3dexport
truck
archibase_planet
free
Truck
...truck
archibase planet
truck truck crane car
truck toyota n071013 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Truck
...truck
archibase planet
truck lorry car
truck - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Truck
...truck
archibase planet
truck lorry car
truck n260213 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
3d_export
$5
truck
...truck
3dexport
3d model of a truck, made for optimus prime!
3d_ocean
$19
Truck
...truck
3docean
four-wheel max truck
precision four-wheel drive truck with mud mask effect, the door can be opened
archibase_planet
free
Truck
...truck
archibase planet
truck car broken car lorry
truck broken - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Truck
...truck
archibase planet
truck lorry autotruck
truck kenworth t600 n280113 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Truck
...
archibase planet
truck freightliner lorry car
truck freightliner n200314 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Truck
...truck
archibase planet
truck lorry autotruck
truck 4 eu n160614 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
Bear
3d_export
$6
Bear
...bear
3dexport
bear
3d_export
$5
bearing
...bearing
3dexport
bearing
3d_export
$12
bear
...bear
3dexport
bear for 3d printing toy
3d_ocean
$9
Bearing
...ne ball ballbea bearing bearings engine hard industrial machine mechanic metal part piece plastic ring screw sphere steel
bearing
archibase_planet
free
Bear
...bear
archibase planet
statuette bear picturesque element
bear - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
bear
...bear
3dexport
bear have a stl.,3dm files
archibase_planet
free
Bear
...bear
archibase planet
bear animals omnivorous animal
bear angry n250907- 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Bear
...bear
archibase planet
bear animals omnivorous animal
bear easy n250907 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3ddd
$1
Teddy bear
...teddy bear
3ddd
teddy bear , медведь
teddy bear :)
3d_ocean
$12
Bear
... formats. created with 3d max 9.0. this file is very useful for learning & rigging. it can be used for any professional work.
Fully
turbosquid
$50
Drone fully rigged
...
royalty free 3d model drone fully rigged for download as max on turbosquid: 3d models for games, architecture, videos. (1282280)
turbosquid
$12
FULLY PARAMETRIC CHAIR
...alty free 3d model fully parametric chair for download as rvt on turbosquid: 3d models for games, architecture, videos. (1280209)
turbosquid
$10
firetruck-fully-rigged
...yalty free 3d model firetruck-fully-rigged for download as ma on turbosquid: 3d models for games, architecture, videos. (1653811)
turbosquid
$6
Fully rigged character
...ty free 3d model fully rigged character for download as blend on turbosquid: 3d models for games, architecture, videos. (1486076)
turbosquid
$3
Fully Rigged shark
...ee 3d model fully rigged 3d shark model for download as blend on turbosquid: 3d models for games, architecture, videos. (1517695)
turbosquid
$75
Fully Customizable Hospital
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Fully Rigged Link
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
design_connected
$16
Troy W Fully Covered
...troy w fully covered
designconnected
magis troy w fully covered computer generated 3d model. designed by wanders, marcel.
cg_studio
$99
Pepe fully rigged3d model
...ully rigged3d model
cgstudio
.max - pepe fully rigged 3d model, royalty free license available, instant download after purchase.
3d_export
$60
Ankylosaur 8K - fully animated
...ankylosaur 8k - fully animated
3dexport
Printable
turbosquid
$5
printable giraffe
...uid
royalty free 3d model printable giraffe for download as on turbosquid: 3d models for games, architecture, videos. (1504825)
turbosquid
$49
Longhorn Printable
...
royalty free 3d model longhorn printable for download as stl on turbosquid: 3d models for games, architecture, videos. (1712930)
3d_export
$2
printable audi car
...printable audi car
3dexport
printable audi car
turbosquid
$40
Fox printable
...lty free 3d model fox printable for download as blend and stl on turbosquid: 3d models for games, architecture, videos. (1507558)
turbosquid
$23
Printable Statue
...ty free 3d model printable statue for download as obj and stl on turbosquid: 3d models for games, architecture, videos. (1415137)
turbosquid
$3
Ear Printable
...yalty free 3d model ear printable for download as obj and stl on turbosquid: 3d models for games, architecture, videos. (1671689)
turbosquid
$1
heart printable
...y free 3d model heart printable for download as stl and sldpr on turbosquid: 3d models for games, architecture, videos. (1209566)
turbosquid
$1
Printable Hook
...
royalty free 3d model 3d printable hook for download as stl on turbosquid: 3d models for games, architecture, videos. (1413683)
turbosquid
$30
Printable support
... model 3d printable support for download as max, 3ds, and stl on turbosquid: 3d models for games, architecture, videos. (1689342)
turbosquid
$24
Printable Dolphin
...el printable dolphin for download as , dae, fbx, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1602353)