Tumbler Drum by thingirob

...verse this thing is a work in progress. it will be an agitator to insert into a tumbler drum to help mix things up a bit better

... goop... something. i have yet to print this, so feedback about the overhang or thickness of the walls/flange is very welcome.

...his to sort the stainless steel pins from the cases. printer ender 3 v2 pla+ sunlu print speed @100 infill 20% quality 0.28(low)

...will increase the inner diameter of the lid. you can use this to account for how snug or loose the fit of the lid is to the drum.

...nted all parts at 100% infill. just print 2 of everything, install with hardware, adjust, and enjoy quiet friction-free tumbling.

...tumbler by yuh1973 thingiverse tumbler

...vaso - tumbler by doctormao thingiverse vaso - tumbler

...gly on top of the drums of a harbor freight rock tumbler. a few good shakes and the media falls through leaving behind the brass.

...n the lid easier. the hal-sphere at the bottom of the drum is because the leifheit-container has a "bump" at that spot.

...national geographic tumbler cap by yersundanny thingiverse design for tumbler

...example by thingirob thingiverse example

...y dragonfire81m thingiverse z mount for 40mmx40mm z tower for tevo tarantula. used thingirob design v2 loaded all good to go .

...files for the motor mount (https://www.thingiverse.com/supasorn/about) all parts are heavily modified or completely redone by me.

...et on the lower inside of the headlight housing. glues on. i think the stl is the right hand side, just mirror for the left side.

...t look any better after the hack saw mod =) added a different easier method. just have to drill some 6mm/.25in or so holes in it.

... reset button on the display so you can stop it from committing hari kari if there is a problem with a limit switch or something.

...in an audi b5 s4. it fits many shifters of the same era (2000ish). have installed in 6spd s4 and allroad. not sure about a4 5spd.

... thanks to thingirob for the design. it's package in with his brackets that i used. https://www.thingiverse.com/thing:1457449

... thingirob design by dragonfire81m thingiverse use this brace with 20x40 left side tower and 20x40 top rail for tevo tarantula

...tumbler by yuh1973 thingiverse tumbler

...vaso - tumbler by doctormao thingiverse vaso - tumbler

...0r thingiverse another tumbler... again... the script to create your own tumbler is here: http://www.thingiverse.com/thing:20188

...vibratory tumbler by firegiy1 thingiverse good tumbler 70mm fan with nut in one blade

...rock tumbler by myrmidon93 thingiverse design i was working on for a rock tumbler. will add more as i finish

...ultirap thingiverse a tumbler, watertight, decagonal design. more information on http://www.multec.dehttp://youtu.be/tsspkxklmsi

...rock tumbler canister by dcrispy thingiverse a alternative canister for tumblers

...tumbler type 1 by cassettegirl thingiverse simple tumbler based on ikea pokal

...the tumbler without needing to be replaced. circle on bottom of jig lines up with circle on bottom of tumbler for easy alignment

...drum thingiverse drum

...drums thingiverse it is fully 3d printable modular drums with different heights and drum sticks.

...drum by syzguru11 thingiverse drum

...bitholder drums thingiverse bitholder for drums

... key thingiverse drum key for your drum kit! check out all the drumming models here: https://www.youtube.com/watch?v=80-ciqnk_sy

...drum thingiverse luke donoway

...bmc018 analog drum thingiverse bmc018 analog drum 3u 8hp (http://www.bartonmusicalcircuits.com/drum/)

...bass drum by williestewart thingiverse bass drum

...drum lugs by soares_g thingiverse drum lugs abs