Thingiverse
Trium3D enclosure mount by lucapaschi
by Thingiverse
Last crawled date: 3 years ago
Beware, it's still a work in progress! I won't be able to try all parts now, but should fit nicely.
I had to think about a way to safely block access to hot and moving parts! Should also work to have a temperature controlled environment.
The hinges should be mounted on the frame, the same way as the top and bottom part: 1xM6x10mm screw and nut.
For the opening panels, the lock bar should be mounted with 2xM6 nut and bolts, while the rotating part should be mounted on the panel (M4 bolts).
If you want to have a fixed panel, just mount the bracket with 2xM6 nuts and bolts on the frame, and then on the panel (M4 bolts).
The other parts should be mounted on a polycarbonate panel, with the following dimensions: 29x75cm, 1/1,5 mm thickness (WARNING: check dimensions on all sides of your printer, as they may slighty vary beacuse of assembly: gap between the beams, and from the bed to the top parts of the frame). Thicker panels might be unable to close fully.
I had to think about a way to safely block access to hot and moving parts! Should also work to have a temperature controlled environment.
The hinges should be mounted on the frame, the same way as the top and bottom part: 1xM6x10mm screw and nut.
For the opening panels, the lock bar should be mounted with 2xM6 nut and bolts, while the rotating part should be mounted on the panel (M4 bolts).
If you want to have a fixed panel, just mount the bracket with 2xM6 nuts and bolts on the frame, and then on the panel (M4 bolts).
The other parts should be mounted on a polycarbonate panel, with the following dimensions: 29x75cm, 1/1,5 mm thickness (WARNING: check dimensions on all sides of your printer, as they may slighty vary beacuse of assembly: gap between the beams, and from the bed to the top parts of the frame). Thicker panels might be unable to close fully.
Similar models
thingiverse
free
Tevo Tarantula simpler adjustable Z stop by yelkao
... using the 30mm m5 bolts that come with the tarantula.
parts
4 x m4 bolts
4 x m4 tnuts
1 x m5 bolt 30mm or more
2 x m5 hex nuts
thingiverse
free
Laptop Stand for Vesa Mount by carlol
...th or longer)
as you can see in the photo, i used hex machine screws which fit into the model, but any m4 nuts/bolts should work.
thingiverse
free
Top mounted filament roller
...uploaded,i have opened up the filament path.
top mounted filament roller,
requires fidget spinner bearing and m4 bolt and t nut .
thingiverse
free
M4 Bed Leveling Knob
...s) from the top, remove the sacrificial layer, clean the leftovers from the cut and you'r good to go.
hardware needed: m4 nut
thingiverse
free
1 inch bar panel mount clamp
...e
i designed these to mount flat panels to 1 inch bar on a kit car should work with any 1 inch bar using m6 bolts and 10mm nuts.
thingiverse
free
Kossel Rod Jig by xile6
...ame.
picture is my carbon rods ,which im replacing because they crack, but have metal ones on the way. thats why i made this jig.
thingiverse
free
2020 PSU Bracket by TechGirl_Mods
...y psu on my hypercube corexy 2020 frame.
it mounts to the frame using m5 bolts and slot-in t-nuts, and m4 bolts to mount the psu.
thingiverse
free
easyDelta rigid frame by dolpin
...rews with a ring. a 4.5x30 wood screw can be used to attach the part of the bracket pointing towards the center to the top plate
thingiverse
free
SnapMaker Dremel Flex Shaft Mount by CthulhuLabs
...dremel flex shaft
please note that i have not tested this at all. i am not sure i have it even in the correct place on the mount.
thingiverse
free
2020 extrusion Ender LCD Mount by sychan
...lts will contact the motherboard). the mounting bracket uses 2 m4 screws + t-nuts to attach to the 2020 extrusion on the ender 5
Lucapaschi
thingiverse
free
Trium3D FSR board mount by lucapaschi
...om the aluminium bed, or bad things might happen if the board goes off balance and touches the frame while the printer is active.
thingiverse
free
Trium3D printer fan duct and spacer by lucapaschi
...rious deisgns: i hope it can be improved in the future!
link to "open" shroud: http://www.thingiverse.com/thing:2037173
thingiverse
free
Trium3D printer "open" fan duct and spacer by lucapaschi
...n of various deisgns: i hope it can be improved in the future!
link to the other shroud: http://www.thingiverse.com/thing:2035471
Trium3D
thingiverse
free
Filament Guide v3 for Trium3D printer by KnoxD
... by knoxd
thingiverse
this is an filament guide fitting to the extruder used by the trium3d 3d printer from emergin innovations.
thingiverse
free
Trium3D zip tie mount by Rajaa
...ie mount by rajaa
thingiverse
mount for zip tie to mount rubber instead of springs for the effector, and mount flying extruders.
thingiverse
free
3 Spools Holder For Trium3D by Rajaa
...iverse
5mm/361mm axis. m3 screws and nuts.100% infill.
if the holes came out tight for the screws, just drill them with 3mm bit.
thingiverse
free
Trium3D E3D Effector Fan Duct by LeeIIIWill
...remixed from euphy's e3d v6 duct. uses 2x 40mm fans. may modify farther in the future for more direct air flow to the hotend.
thingiverse
free
Belt tensioner for Trium3D printer by Rajaa
...-m5 screw and nut, 40mm.
-if the screw didn't fit freely, just drill the holes with 5mm bit (for the small hole use 4mm bit).
thingiverse
free
Trium3D FSR board mount by lucapaschi
...om the aluminium bed, or bad things might happen if the board goes off balance and touches the frame while the printer is active.
thingiverse
free
T3D v2.0 - FSR Support by E-Mergin
...for johnsl fsr kit. this is dev part for trium3d v2.0, can be used on trium3d v1.0 as...
thingiverse
free
Trium3D printer fan duct and spacer by lucapaschi
...rious deisgns: i hope it can be improved in the future!
link to "open" shroud: http://www.thingiverse.com/thing:2037173
thingiverse
free
Trium3D printer "open" fan duct and spacer by lucapaschi
...n of various deisgns: i hope it can be improved in the future!
link to the other shroud: http://www.thingiverse.com/thing:2035471
Enclosure
3d_export
free
electrical enclosure
...l enclosure where electrical devices like (relays, contactors, busbars ) are kept in order to protect from hazardous environment.
turbosquid
$100
GPU Enclosure
...yalty free 3d model gpu enclosure for download as obj and stl on turbosquid: 3d models for games, architecture, videos. (1381061)
3d_export
$5
Electrical Enclosure
...ed. also has tower lights attaced on the top.<br>file format that are available:<br>.step<br>.obj<br>.stl
archive3d
free
Enclosure 3D Model
...closure 3d model
archive3d
shower enclosure-acquarius- 3d model for interior 3d visualization.
archive3d
free
Enclosure 3D Model
...enclosure 3d model
archive3d
shower enclosure-omega- 3d model for interior 3d visualization.
archive3d
free
Enclosure 3D Model
...enclosure 3d model
archive3d
shower enclosure-vega - 3d model for interior 3d visualization.
archive3d
free
Enclosure 3D Model
...enclosure 3d model
archive3d
shower enclosure-zenith - 3d model for interior 3d visualization.
turbosquid
$20
shower enclosure
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$14
Dumpster Enclosure
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$25
3d printer enclosure
... model 3d printer enclosure for download as ipt, skp, and fbx on turbosquid: 3d models for games, architecture, videos. (1634310)
Mount
3d_export
free
mounting bracket
...mounting plate is the portion of a hinge that attaches to the wood. mounting plates can be used indoors, cabinetry and furniture.
turbosquid
$2
MOUNTING
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mounts
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mount Fuji
...fuji
turbosquid
free 3d model mount fuji for download as obj on turbosquid: 3d models for games, architecture, videos. (1579977)
3d_export
$5
Headphone mount LR
...headphone mount lr
3dexport
headphone mount l+r
turbosquid
$39
Mount rainier
...quid
royalty free 3d model mount rainier for download as fbx on turbosquid: 3d models for games, architecture, videos. (1492586)
turbosquid
$5
pipe mounting
...quid
royalty free 3d model pipe mounting for download as obj on turbosquid: 3d models for games, architecture, videos. (1293744)
turbosquid
$3
Mounting Tires
...uid
royalty free 3d model mounting tires for download as fbx on turbosquid: 3d models for games, architecture, videos. (1708511)
3d_export
$5
Magnetic GoPro Mount
...pro mount
3dexport
cool magnetic mount for gopro. allows you to mount the camera on flat metal surfaces and get exclusive shots.
turbosquid
$5
Stone Mount
...ty free 3d model stone mount for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1370306)