Thingiverse
![Trigorilla Fan Mount for Stepper Controller / TMC2100 by peaberry](/previews/8569890.jpg)
Trigorilla Fan Mount for Stepper Controller / TMC2100 by peaberry
by Thingiverse
Last crawled date: 3 years, 1 month ago
This is a minimal fan mounting bracket for the Trigorilla Mainboard on the Anycubic Linear Kossel. I made this as a simple way to mount a 40mm radial blower fan to cool my TMC2100 stepper drivers (not wanting to print a fully enclosed tunnel, because I already have a panel between the hot bed and PCB). The fan is attached by driving a 3mm screw directly into the bracket (cutting its own thread). The bracket is attached to the PCB with one M3 screw and nut.
I connected the fan to the unused FAN1 connector on the Trigorilla board, which is controlled by PIN 7 of the controller board. I enabled this by making the following changes in Marlin "Configuration_adv.h":
#define USE_CONTROLLER_FAN
#if ENABLED(USE_CONTROLLER_FAN)
#define CONTROLLER_FAN_PIN 7 // FAN1 is Pin 7 on Trigorilla Board
#define CONTROLLERFAN_SECS 60 // Duration in seconds to run after motors disabled
#define CONTROLLERFAN_SPEED 255 // 255 == full speed
#endif
This works really nicely as the fan switches on automatically when the stepper drivers are enabled, and runs for another 60 seconds after they are turned off.
It took me a while to get the TMC2100 drivers working well. In an attempt to make it use spreadCycle mode, I started by cutting off the CFG1-3 pins and bridging CFG1 to GND with a wire. It turns out this doesn't have any effect on the particular TMC2100 driver I'm using. The drivers were still in stealthChop and kept missing steps and skewing layers, no matter which Vref I used. Eventually I discovered there are two tiny solder pads under the board which need to be bridged to connect CFG1 to GND and enable spreadCycle mode. Now it finally works well...
I connected the fan to the unused FAN1 connector on the Trigorilla board, which is controlled by PIN 7 of the controller board. I enabled this by making the following changes in Marlin "Configuration_adv.h":
#define USE_CONTROLLER_FAN
#if ENABLED(USE_CONTROLLER_FAN)
#define CONTROLLER_FAN_PIN 7 // FAN1 is Pin 7 on Trigorilla Board
#define CONTROLLERFAN_SECS 60 // Duration in seconds to run after motors disabled
#define CONTROLLERFAN_SPEED 255 // 255 == full speed
#endif
This works really nicely as the fan switches on automatically when the stepper drivers are enabled, and runs for another 60 seconds after they are turned off.
It took me a while to get the TMC2100 drivers working well. In an attempt to make it use spreadCycle mode, I started by cutting off the CFG1-3 pins and bridging CFG1 to GND with a wire. It turns out this doesn't have any effect on the particular TMC2100 driver I'm using. The drivers were still in stealthChop and kept missing steps and skewing layers, no matter which Vref I used. Eventually I discovered there are two tiny solder pads under the board which need to be bridged to connect CFG1 to GND and enable spreadCycle mode. Now it finally works well...
Similar models
thingiverse
free
![Anycubic Delta Kossel Stepper Driver Aero Tunnel Cooler 40X40 by VitaliySh](/t/8620101.jpg)
Anycubic Delta Kossel Stepper Driver Aero Tunnel Cooler 40X40 by VitaliySh
...tion in seconds for the fan to run after all motors are disabled
define controllerfan_speed 255 // 255 == full speed
endif
thingiverse
free
![Cooling duct for Anycubic Kossel Trigorilla by Deln555](/t/8534303.jpg)
Cooling duct for Anycubic Kossel Trigorilla by Deln555
...er all .motors are disabled
. #define controllerfan_speed 255 // 255 == full speed
.#endif
thanks!
update: add curved version.
thingiverse
free
![Anycubic Kossel PCB cooling 40x40 fan + stepper driver Aero Tunnel by Facocero](/t/8776635.jpg)
Anycubic Kossel PCB cooling 40x40 fan + stepper driver Aero Tunnel by Facocero
...v1.2:
tunnel with increased height and length for tmc2100 + protector filter or with big heat sink for higher cooling performance
thingiverse
free
![Trigorilla Board (Anycubic) Stepper Driver Cooling by lexaiden](/t/8534961.jpg)
Trigorilla Board (Anycubic) Stepper Driver Cooling by lexaiden
...anycubic firmware version).
i use this fan duct to cool tmc2208 stepper drivers (the printer is so silent with these drivers...).
thingiverse
free
![ESS Smooth stepper DIN rail mounting clip by bonaur](/t/8952874.jpg)
ESS Smooth stepper DIN rail mounting clip by bonaur
...mooth stepper pcb-board from warp9.
this enables the pcb-board to mounted on a 35mm din rail used in electrical control cabinets.
thingiverse
free
![30mm dual fan stepper driver cooler mount by abailey](/t/8684798.jpg)
30mm dual fan stepper driver cooler mount by abailey
...ed.
printed on my cel robox with 100% infill since i'm reworking the elecronics on my kossel (which includes this new cooler)
thingiverse
free
![Anycubic Kossel stepper cooling bracket by vdwel](/t/8259426.jpg)
Anycubic Kossel stepper cooling bracket by vdwel
...7
connected the fan to fan1 and reduced the speed of the fan to 180 in the firmware:
configuration_adv.h:
controllerfan_speed 180
thingiverse
free
![HICTOP 3DP11 MKS Gen 1.4 Mounting Bracket by pyr0ball](/t/8613785.jpg)
HICTOP 3DP11 MKS Gen 1.4 Mounting Bracket by pyr0ball
...and have more output pins available.
i also designed a fan shroud to compliment this mount, and keep all the stepper drivers cool
thingiverse
free
![Anycubic main board cooling duct by namomo](/t/8735953.jpg)
Anycubic main board cooling duct by namomo
...00 which makes a lot of heat.
happy printing everyone.
trigorilla pcb main board mount : http://www.thingiverse.com/thing:2155376
thingiverse
free
![Little Monster External Stepper Driver Box by dot_bob](/t/8711726.jpg)
Little Monster External Stepper Driver Box by dot_bob
...e little monster.
the board you see in the back is just a 20mm x 80mm generic perf board used to couple the power wires together.
Tmc2100
thingiverse
free
![CR-8 TMC2100 FanDuct-V2 by Samie828](/t/8845448.jpg)
CR-8 TMC2100 FanDuct-V2 by Samie828
...cr-8 tmc2100 fanduct-v2 by samie828
thingiverse
2016-02-20 cr-8 改新 tmc2100 散熱罩
thingiverse
free
![CR-8 TMC2100 FanDuct-V1 by Samie828](/t/8845445.jpg)
CR-8 TMC2100 FanDuct-V1 by Samie828
...cr-8 tmc2100 fanduct-v1 by samie828
thingiverse
2016-02-03 cr-8 tmc2100驅動板散熱座
thingiverse
free
![ATOM TMC2100 fan cover by godjay](/t/8655627.jpg)
ATOM TMC2100 fan cover by godjay
...atom tmc2100 fan cover by godjay
thingiverse
for atom 2.5ex
thingiverse
free
![CR8 TMC2100 Fan by sdpflying](/t/8770545.jpg)
CR8 TMC2100 Fan by sdpflying
... 70% to tmc2100 ,but it pn;y give the wind to the x y step motor,if you change 3 or 4 step motor,this design can't work well.
thingiverse
free
![Voron 24v TMC2100 Upgrade Kit by JacobMakes](/t/8799712.jpg)
Voron 24v TMC2100 Upgrade Kit by JacobMakes
...ade my ramps 1.4 on the voron corexy!
find my tutorial here!https://www.youtube.com/watch?v=cdmxwpnk1ku&ab_channel=jacobmakes
thingiverse
free
![Tevo Delta (Little Monster) TMC2100 bracket by Spirit00](/t/8663533.jpg)
Tevo Delta (Little Monster) TMC2100 bracket by Spirit00
...
works great in combination with my lm cable (management) bracket: https://www.thingiverse.com/thing:2509575
you are welcome! ;-)
thingiverse
free
![StepStick blower tunnel for cooling (for AZSMZ, MKS GEN) by cyberbsd](/t/8921778.jpg)
StepStick blower tunnel for cooling (for AZSMZ, MKS GEN) by cyberbsd
...cooling (for azsmz, mks gen) by cyberbsd thingiverse trinamic tmc2100 so hot! the blower:...
thingiverse
free
![RuRamps Adapter for Delta Anycubic by karnhack](/t/8547638.jpg)
RuRamps Adapter for Delta Anycubic by karnhack
...update: add a driver cooler for 25x25x10.3 fan (driver tmc2100 with high heat...
thingiverse
free
![Gen L cool fan stand alone](/t/4896903.jpg)
Gen L cool fan stand alone
...is for cooling the mkg gen l with the tmc2100 drivers all you need is 12 x m3 x...
Peaberry
thingiverse
free
![595 Abarth Logo by peaberry](/t/8615282.jpg)
595 Abarth Logo by peaberry
...595 abarth logo by peaberry
thingiverse
595 abarth logo
thingiverse
free
![Turismo Abarth Logo by peaberry](/t/8615284.jpg)
Turismo Abarth Logo by peaberry
...turismo abarth logo by peaberry
thingiverse
turismo abarth logo
thingiverse
free
![20x20 Extrusion 100mm Length by peaberry](/t/8747954.jpg)
20x20 Extrusion 100mm Length by peaberry
...20x20 extrusion 100mm length by peaberry
thingiverse
basic length of 2020 extrusion, mainly for use as a reference in modelling.
thingiverse
free
![2020 Cable Clip by peaberry](/t/8748314.jpg)
2020 Cable Clip by peaberry
...ple cable clip for 2020 extrusion, intended for cable which lies in the channel. two different widths are provided, 5mm and 10mm.
thingiverse
free
![DIN Rail Spring Clip by peaberry](/t/9222337.jpg)
DIN Rail Spring Clip by peaberry
... mounting clip for 35mm din rails. it includes mounting holes on 35mm and 40mm centres, which have an internal diameter of 2.5mm.
thingiverse
free
![2020 Flat Cable Clip 10mm length by peaberry](/t/8747957.jpg)
2020 Flat Cable Clip 10mm length by peaberry
...lat cable clip 10mm length by peaberry
thingiverse
simple and discreet flat clip for securing cables in 2020 extrusion channels.
thingiverse
free
![LM2596 Module Support by peaberry](/t/8286536.jpg)
LM2596 Module Support by peaberry
...s with 3mm internal diameter, and two additional pins to ensure the board has support at all four corners. overall height is 3mm.
thingiverse
free
![Replacement Knob for Extension Lead (Masterplug 20m) by peaberry](/t/8701169.jpg)
Replacement Knob for Extension Lead (Masterplug 20m) by peaberry
...lead (masterplug 20m) by peaberry
thingiverse
replacement for a broken knob on the masterplug 20m 4 socket mains extension lead.
thingiverse
free
![Canon LP-E10 Battery Cover by peaberry](/t/8606558.jpg)
Canon LP-E10 Battery Cover by peaberry
...mple battery cover for canon lp-e10 camera batteries. protects the battery contacts and reduces the risk of shorting the battery.
thingiverse
free
![AA / AAA Battery Holder / Box by peaberry](/t/8532828.jpg)
AA / AAA Battery Holder / Box by peaberry
...ngiverse
battery box for eight aa or aaa batteries.
internal diameters are 15mm for aa and 11mm for aaa. overall height is 14mm.
Trigorilla
thingiverse
free
![Trigorilla Case by Merlin2105](/t/8310705.jpg)
Trigorilla Case by Merlin2105
...trigorilla case by merlin2105
thingiverse
case for trigorilla board
40mm noctua lüftergschutz
thingiverse
free
![Case trigorilla for anycubic by MakerDog1](/t/8689505.jpg)
Case trigorilla for anycubic by MakerDog1
...case trigorilla for anycubic by makerdog1
thingiverse
case trigorilla for anycubic
thingiverse
free
![AnyCubic Trigorilla Case by Spacemanballz](/t/8281284.jpg)
AnyCubic Trigorilla Case by Spacemanballz
...anycubic trigorilla case by spacemanballz
thingiverse
external trigorilla case
m3 nut fit
30mm fan fitting
thingiverse
free
![Trigorilla port documentation by an_da_liu](/t/8669546.jpg)
Trigorilla port documentation by an_da_liu
...ocumentation by an_da_liu
thingiverse
additional documentation i made for the trigorilla controll board in the anycubic printer.
thingiverse
free
![Trigorilla 2020 Mount by Mka0205](/t/8314813.jpg)
Trigorilla 2020 Mount by Mka0205
...by mka0205
thingiverse
i was in need of a simple way to mount my trigorilla board to my hypercube 2020 extrusion so i made this.
thingiverse
free
![Fan 4010 for drivers trigorilla](/t/4979098.jpg)
Fan 4010 for drivers trigorilla
...fan 4010 for drivers trigorilla
thingiverse
print vertical
thingiverse
free
![TriGorilla board mockup by AlexWaveDiver](/t/8662161.jpg)
TriGorilla board mockup by AlexWaveDiver
...ur cables and case setup without risking a real board.
feel free to comment. criticism is always welcome, as it helps me improve!
thingiverse
free
![Anycubic Trigorilla Board Mount by hanser30](/t/8739858.jpg)
Anycubic Trigorilla Board Mount by hanser30
...t is specially made for the anycubic linear plus but it could be used in the non plus version and in the pulley version as well.
thingiverse
free
![Anycubic Trigorilla Board Template by SirGed](/t/8521384.jpg)
Anycubic Trigorilla Board Template by SirGed
...o an enclosure that mine went into for another build. included a plate as well if you just want to cover the bottom of the board.
thingiverse
free
![Trigorilla MOSFET mount for 2020 extrusion by stormtrooperguy](/t/8696291.jpg)
Trigorilla MOSFET mount for 2020 extrusion by stormtrooperguy
...uy
thingiverse
i made this to mount a trigorilla mosfet on my reworked folgertech i3. should be suitable for any 2020 extrusion.
Stepper
thingiverse
free
![stepper motor](/t/4753235.jpg)
stepper motor
...stepper motor
thingiverse
this is experimental.
a nearly fully 3d printed stepper motor.
thingiverse
free
![stepper bracket by Brennenenenenen](/t/8832819.jpg)
stepper bracket by Brennenenenenen
...stepper bracket by brennenenenenen
thingiverse
stepper motor bracket thats holds the stepper at a 90 degree angle
thingiverse
free
![Stepper Attachment by googlebleh](/t/8738971.jpg)
Stepper Attachment by googlebleh
...stepper attachment by googlebleh
thingiverse
for a 5mm stepper
thingiverse
free
![Mount stepper by Salin](/t/8605568.jpg)
Mount stepper by Salin
...mount stepper by salin
thingiverse
stepper 42mm
thingiverse
free
![STEPPER PICCOLO by SergioPapagni](/t/8922566.jpg)
STEPPER PICCOLO by SergioPapagni
...stepper piccolo by sergiopapagni
thingiverse
stepper piccolo
thingiverse
free
![Stepper Motor Piece](/t/4971819.jpg)
Stepper Motor Piece
...stepper motor piece
thingiverse
this is for a stepper motor
thingiverse
free
![stepper by DogmaGab](/t/8803815.jpg)
stepper by DogmaGab
...stepper by dogmagab
thingiverse
a
thingiverse
free
![Stepper Motor by kevin02](/t/8587812.jpg)
Stepper Motor by kevin02
...stepper motor by kevin02
thingiverse
a model of a stepper motor
thingiverse
free
![Stepper Cooler by utilitybee](/t/8916447.jpg)
Stepper Cooler by utilitybee
... a 40mm fan and zip tie to stepper.
brought my stepper temps from 80c to 40c
was made to work on the smaller nema 17 steppers
thingiverse
free
![Stepper motor by umbertocilia](/t/8911184.jpg)
Stepper motor by umbertocilia
...stepper motor by umbertocilia
thingiverse
stepper motor from harddrive
Controller
thingiverse
free
![Megapoints Controllers - Servo Controller by SoBaldrick](/t/8577701.jpg)
Megapoints Controllers - Servo Controller by SoBaldrick
...megapoints controllers - servo controller by sobaldrick
thingiverse
megapoints controllers - servo controller base
thingiverse
free
![controller by tahmasnx](/t/8775161.jpg)
controller by tahmasnx
...controller by tahmasnx
thingiverse
controller fusion 360
thingiverse
free
![Control panel](/t/4715315.jpg)
Control panel
...control panel
thingiverse
control panel for scuba regulator/bank system
thingiverse
free
![ph controller](/t/4872708.jpg)
ph controller
...ph controller
thingiverse
pi zero based reef-pi ph controller
thingiverse
free
![NES Controller](/t/4884055.jpg)
NES Controller
...nes controller
thingiverse
this is just a simple nes controller prop. display purposes only.
thingiverse
free
![Frame control](/t/5002176.jpg)
Frame control
...frame control
thingiverse
installation led 12864 reprapdiscount for control machine 3d printer.
thingiverse
free
![Control Tower](/t/4912374.jpg)
Control Tower
...control tower
thingiverse
control tower or marshall tower for 1/32 slot car track
thingiverse
free
![Controller Hook by P0chapa](/t/8272666.jpg)
Controller Hook by P0chapa
... for (maybe) any game controller.
i attached this thing to ps2 controller and third-party xbox controller with double sided tape.
thingiverse
free
![Xbox 360 controller stand for 3 controllers by afrolucas](/t/8742895.jpg)
Xbox 360 controller stand for 3 controllers by afrolucas
...xbox 360 controller stand for 3 controllers by afrolucas
thingiverse
update for 3 controllers
thingiverse
free
![PS4 Controller Stand for 3 Controllers (Dualshock 4)](/t/4890978.jpg)
PS4 Controller Stand for 3 Controllers (Dualshock 4)
...the stands for a nvidia shield controller rather than a ps4 controller (so two ps4 controllers and one nvidia shield controller).
Fan
thingiverse
free
![Fan Duct 60mm fan](/t/4774802.jpg)
Fan Duct 60mm fan
...fan duct 60mm fan
thingiverse
this a 60mm fan adaptor
thingiverse
free
![Fan Stand 140mm Fan by Aron84](/t/8126613.jpg)
Fan Stand 140mm Fan by Aron84
...fan stand 140mm fan by aron84
thingiverse
fan stand for 140x140x27mm fan
thingiverse
free
![Fan wall for 40mm fan by Nule](/t/8951855.jpg)
Fan wall for 40mm fan by Nule
...fan wall for 40mm fan by nule
thingiverse
fan aislator for 40mm fan with meshmixer support
thingiverse
free
![Fan holder 40mm fan for V67](/t/4725979.jpg)
Fan holder 40mm fan for V67
...n for v67
thingiverse
fan holder 40mm fan for v67
fan: https://www.amazon.de/dp/b07vhmv4dz/ref=cm_sw_r_other_apa_i_803cebwt8kvpe
thingiverse
free
![Fan cover & fan grill to suit 50mm fan by Phil_Maddox](/t/8891959.jpg)
Fan cover & fan grill to suit 50mm fan by Phil_Maddox
...fan cover & fan grill to suit 50mm fan by phil_maddox
thingiverse
simple fan cover for 50 x 50 x 10 fan
thingiverse
free
![Fan grille for 50mm fan andE3D V6 Fan Duct for 50mm Fan V2 by vitaly12](/t/8053653.jpg)
Fan grille for 50mm fan andE3D V6 Fan Duct for 50mm Fan V2 by vitaly12
...for 50mm fan ande3d v6 fan duct for 50mm fan v2https://www.thingiverse.com/thing:4662850
height:3.5mm
40mm fan grille coming soon
thingiverse
free
![Fan Grid for 127mm Fan by MasterFX](/t/8967030.jpg)
Fan Grid for 127mm Fan by MasterFX
...fan grid for 127mm fan by masterfx
thingiverse
just a simple fan grid for unusual 127mm fan
thingiverse
free
![Fan Showdown fan submission by DAraymond](/t/9685464.jpg)
Fan Showdown fan submission by DAraymond
...fan showdown fan submission by daraymond
thingiverse
this is a fan i submitted for the youtube fan showdown series.
thingiverse
free
![Fan Shroud](/t/4885278.jpg)
Fan Shroud
...fan shroud
thingiverse
this is a fan shroud for a 140mm fan
thingiverse
free
![Mosaic Fan on Fan by bwevans](/t/9058673.jpg)
Mosaic Fan on Fan by bwevans
...a fan mount for the second fan that's included in the mosaic kit but is lacking any hardware. really useful for printing pla!
Mount
thingiverse
free
![Pen Mount on BLTouch mount by jetspot](/t/8008768.jpg)
Pen Mount on BLTouch mount by jetspot
...pen mount on bltouch mount by jetspot
thingiverse
pen mount on bltouch mount
thingiverse
free
![RAM Mount, Mount by seanmclean](/t/8576780.jpg)
RAM Mount, Mount by seanmclean
...ram mount, mount by seanmclean
thingiverse
bridging plate to attach ram mount to yamaha 242, for chartplotter placement.
thingiverse
free
![Mount for mount for Garmin GPS by GNOBLIN](/t/8370409.jpg)
Mount for mount for Garmin GPS by GNOBLIN
...you can use this mount for prevent rotation simple mount around hendelbars.
d handelbar 31.8mm
use m3 screw and din 16903 plug.
thingiverse
free
![Permanent mount for Modular Mounting System by WIR14](/t/8552241.jpg)
Permanent mount for Modular Mounting System by WIR14
...permanent mount for modular mounting system by wir14
thingiverse
permanent mount for modular mounting system.
thingiverse
free
![Gopro Mount and antenna mount by SuperYoyo](/t/8702832.jpg)
Gopro Mount and antenna mount by SuperYoyo
...gopro mount and antenna mount by superyoyo
thingiverse
cut the carbon platform to pass the gopro mount and enjoy !
thingiverse
free
![Hexagon Mount for 50mm Mount (Sparkcube) by Draman](/t/8715773.jpg)
Hexagon Mount for 50mm Mount (Sparkcube) by Draman
...for 50mm mount (sparkcube) by draman
thingiverse
hexagon mount remix from skimmys hotend-mount for sparkcube or other 50mm-mount
thingiverse
free
![mount by gixster](/t/8146345.jpg)
mount by gixster
...mount by gixster
thingiverse
custom mount
thingiverse
free
![Mount by Matrxi999](/t/8288967.jpg)
Mount by Matrxi999
...mount by matrxi999
thingiverse
shelf mount
thingiverse
free
![Motor mount](/t/4890149.jpg)
Motor mount
...motor mount
thingiverse
motor mount
thingiverse
free
![GoPro Mount](/t/4875481.jpg)
GoPro Mount
...gopro mount
thingiverse
gopro mount