Thingiverse
Toolbox for miniature tools by UroBen
by Thingiverse
Last crawled date: 4 years, 5 months ago
Version II
-Significant changes made to all tool catches, tools fit much better.
-Opening edge slightly modified (-0.010"), case closes better.
-No future versions expected
Story
Annoyed with misplacing my tools at the office I decided to make this toolbox for myself and the technicians. It is a box for the most used,lost and borrowed tools at my office. Please download and enjoy. If you want to make one for your office and need a hand please contact me.
Tools
All the tools can be purchased at McMaster Carr (www.mcmaster.com), here are the order numbers.
Screw driver kit: 52985A22
Hex Driver, 0.05": 5497A22
Hex Driver, 1/16": 5497A23
Hex Driver, 5/64": 5497A24
Hex Driver, 3/32": 5497A25
Hex Driver, 7/64": 5497A26
Tweezers: 5669A13
Brush: 7431T92 or knife: 35545A71
Vial: 5274T69
Magnets
The holes fit 3/16" x 1/2" magnets. Unfortunately McMaster does not carry that size, I purchased 5852K12, a 5" long magnet, and broke and sanded it to make the size needed.
Hinge
The pin for the hinge is a length of 1.75mm ABS filament, cut to length. Add a drop of crazy glue at one end to hold it in place.
Other notes
The brush can be replaced with a small utility knife, but both can't be stored at the same time. There are also spots for seven 1/4" screw bits. As well as three small taps, 2-56, 4-40 and 6-32 shown. Please keep in mind that printing each side takes about 7.5 hours.
Size
Closed the box is about:
Wide: 5.5" (including hinge)
High: 7.0"
Depth: 1.5"
-Significant changes made to all tool catches, tools fit much better.
-Opening edge slightly modified (-0.010"), case closes better.
-No future versions expected
Story
Annoyed with misplacing my tools at the office I decided to make this toolbox for myself and the technicians. It is a box for the most used,lost and borrowed tools at my office. Please download and enjoy. If you want to make one for your office and need a hand please contact me.
Tools
All the tools can be purchased at McMaster Carr (www.mcmaster.com), here are the order numbers.
Screw driver kit: 52985A22
Hex Driver, 0.05": 5497A22
Hex Driver, 1/16": 5497A23
Hex Driver, 5/64": 5497A24
Hex Driver, 3/32": 5497A25
Hex Driver, 7/64": 5497A26
Tweezers: 5669A13
Brush: 7431T92 or knife: 35545A71
Vial: 5274T69
Magnets
The holes fit 3/16" x 1/2" magnets. Unfortunately McMaster does not carry that size, I purchased 5852K12, a 5" long magnet, and broke and sanded it to make the size needed.
Hinge
The pin for the hinge is a length of 1.75mm ABS filament, cut to length. Add a drop of crazy glue at one end to hold it in place.
Other notes
The brush can be replaced with a small utility knife, but both can't be stored at the same time. There are also spots for seven 1/4" screw bits. As well as three small taps, 2-56, 4-40 and 6-32 shown. Please keep in mind that printing each side takes about 7.5 hours.
Size
Closed the box is about:
Wide: 5.5" (including hinge)
High: 7.0"
Depth: 1.5"