Warning. This content is not moderated and could be offensive.

Thingiverse

Throttle Clamp by chromii

Throttle Clamp by chromii

by Thingiverse

Get from Thingiverse

Last crawled date: 3 years, 1 month ago

This is a cable clamp I made for electric car conversions.
I use this with the existing throttle cable to connect it to an electronic hall-effect throttle pot.
It could be used for any cable of the same end bit design.
ie Brake & Clutch cables on Motor Bikes.

Tags

throttle clamp chromii

Similar models

7mm Throttle Cable Clamp by fluin

7mm Throttle Cable Clamp by fluin

...7mm throttle cable clamp by fluin thingiverse fix your broken throttle cable with this clamp.

Domino Racing XM2 Quick Throttle Cable clamp

Domino Racing XM2 Quick Throttle Cable clamp

...e much v2 has 2 holes you need to drill new hole for the second screw, gives better clamping and seal for the cable print at 100%

Throttle grip for motorized bike / motorized bicycle by OkurRo

Throttle grip for motorized bike / motorized bicycle by OkurRo

...hen you destroy (as i did) the original throttle cable. i used the m6 and m4 hex nuts and screws with electrical cable connector.

cable cross clamp by unic8

cable cross clamp by unic8

...sed it to shorten the cord of a ceiling light. i used a power cable with a diameter of 5.25 mm the diameter of the clamp is 2 cm.

Cable clamp for model railway by Freeze

Cable clamp for model railway by Freeze

... for model railway by freeze thingiverse this is a cable clamp for a model railway. i use it to fix hanging cables form the top.

Jeep - Shorten Throttle Cable by cooasty

Jeep - Shorten Throttle Cable by cooasty

...jeep - shorten throttle cable by cooasty thingiverse 1979 cj 5 bushing use to shorten the throttle cable after adding tbi.

Grom throttle quickener by matt_johnson63

Grom throttle quickener by matt_johnson63

...ll this piece, then adjust both that and the closing cable to their most slack positions in order for it to work properly. enjoy!

90 degree cable clamp by superkartoffel

90 degree cable clamp by superkartoffel

...p by superkartoffel thingiverse cable clamp with a 90 degree angle. i use it to mount a small light bulb hanging from the cable.

Cable clip by smcameron

Cable clip by smcameron

...cable clip by smcameron thingiverse this is a cable clip to hold the throttle cable in the cyclekart that i'm building

Throttle Cable Spacer

Throttle Cable Spacer

...l last, and i would not recommend this as a permanent fix. obviously making changes to a throttle cable should be done with care.

Search for 503003 Similar models

Chromii

Flexagon by chromii

Flexagon by chromii

... designed it, so each segment are identical. i will add a link later to a video of it. this thing is very addictive to play with.

Board Game Character by chromii

Board Game Character by chromii

...board game character by chromii thingiverse this is a 3d printable man. for use in diy board games

iPhone4 OtterBox Cradle by chromii

iPhone4 OtterBox Cradle by chromii

... 4(s) while still in it's otterbox. it has ports for the speakers & the option to insert a docking plug for charging etc.

Throttle

Throttle A320 by lolosimule

Throttle A320 by lolosimule

...throttle a320 by lolosimule thingiverse throttle a320

paramotor throttle by patricioruizperret

paramotor throttle by patricioruizperret

...paramotor throttle by patricioruizperret thingiverse paramotor throttle

SSR Throttle

...r throttle thingiverse this is the plastic twist throttle for ssr 110. i printed it with a support where the cable goes through.

Throttle Collar by ericrolfe

Throttle Collar by ericrolfe

...llar by ericrolfe thingiverse collar to connect throttle shaft to slide potentiometer for diy flight simulator throttle control.

Motorcycle Throttle by Someforage

Motorcycle Throttle by Someforage

...motorcycle throttle by someforage thingiverse motorcycle throttle 35mm for heated grip.

CH Throttle Quadrant Throttle Knob by AstarothReborn

CH Throttle Quadrant Throttle Knob by AstarothReborn

...he ch quadrant flight sim controller. not yet tested, as i don't have a printer yet. (also an exercise in learning openscad).

A320 Throttle by MaximeA

A320 Throttle by MaximeA

...a320 throttle by maximea thingiverse a320 throttle prototype , working but still need a lot of work

Throttle Lever Extension

Throttle Lever Extension

...throttle lever extension thingiverse throttle lever extension for saito fa-40 https://youtu.be/bnjgwzeo5ty

Twist Throttle by Mjacobs518

Twist Throttle by Mjacobs518

...twist throttle by mjacobs518 thingiverse twist throttle, this is for a baja 50 mini bike the original one broke.

modified throttle sensor by torrentesoft

modified throttle sensor by torrentesoft

...modified throttle sensor by torrentesoft thingiverse modified throttle sensor

Search for 890 Throttle models

Clamp

Clamp

...clamp thingiverse clamp

Clamp

...clamp thingiverse clamp for vacform

Clamp by bexer

...clamp by bexer thingiverse clamp, one clamp for many possibilities!

clamp by kimduckkyo

clamp by kimduckkyo

...clamp by kimduckkyo thingiverse clamp

clamp by glukofinder

clamp by glukofinder

...clamp by glukofinder thingiverse clamp

Clamp Chain

...clamp chain thingiverse this is a clamp

Clamp by wslab

...clamp by wslab thingiverse clamp

CLAMP by leonk

...clamp by leonk thingiverse clamp

Clamp by jkorinek87

Clamp by jkorinek87

...clamp by jkorinek87 thingiverse clamp

Clamp by Emmanuelgnanasekar

Clamp by Emmanuelgnanasekar

...clamp by emmanuelgnanasekar thingiverse this thing is a clamp model , it can be used for soft clamping things

Search for 14891 Clamp models