Thingiverse
The Laminator by mnis
by Thingiverse
Last crawled date: 3 years ago
So, what is the laminator? ... And what can you do with it? ... And what can you get?
It's exactly this:
The laminator is a simple bonding agent for fixing a hot-laminate film as a removable printing underlay. The preparation of a hot-laminate film to be used as a well-adherent and low-cost object support for problematic PLA filaments (...or special filaments with a similar temperature range.). By creating a very first layer on the laminate film, the film and a carrier plate can be very well connected. Air pockets can be reduced in advance, or at best, they are totally eliminated. In addition, with this first printing process, by observing and adjusting the temperature and motion settings, a later big waste of material due to material warping can be avoided. If the recommendations are correctly implemented, printed surfaces achieve the same gloss level as if they had been printed directly on heated glass (...without adhesive additives.). Once optimally applied, it can be easily printed on the laminate film many times. It lasts for half an eternity until the foil becomes unusable...
I have made many other attempts to apply laminate film bubble free, but this method is currently the best for my concerns.
Introduction:
The laminator is a simple but reliable bonding agent for fixing a ordinary hot-laminate (PP / PE / film 0.08 - 0.12mm) on a build platform as a easy replaceable print underlay for poor adhesion PLA and (experimentally) other filaments. The main purpose of object named: the laminator ;is a good print preparation. In addition to the fixation of the laminate film, the formation of air pockets between the carrier plate and the film to be applied should be avoided as a precaution. For this, the printhead drives at best over the entire base area and creates a first layer, already with the desired material. In the template, almost 100% of the footprint of the Ultimaker 2 is covered, but of course you can make adjustments with the zoom function of the slicer of your choice. A parallel line structure is created, which must of course be removed before the actual printing process. Already during and after this first step you can determine if the material adhesion and the selected temperatures are optimal for the following printing process.
The advantages / disadvantages:
Exemplary example: PLA-HT (by Multec) adheres good to hot-laminate foil. This filament sticks very badly on most common construction surfaces. But it also has many advantages during processing. Because there are almost no lint by retractions and driving without material. Objects with large overhangs succeed better. With this material can be produced very detailed replicas that require very little post-processing. Special filaments or PLA grades with poor adhesion may better adhere to laminate films. No expensive BlueTape, hair spray, or other questionable bonding agent required. Hot-laminate film can be removed at room temperature from many surfaces absolutely residue-free, I have tested it on aluminum with PEI coating. A well-aligned print bed does not need to be re-aligned because the laminate films are very thin (0.08 - 0.12mm). Generally reduce the initial layer thickness by about 33%. So reduce 0.3mm to 0.2mm or just 100% to 66% material flow.
Important:
This method is NOT suitable for filaments printed at very high temperatures above 195...210 degrees in the first layer, or when material generally needs to be kept extremely warm throughout the entire printing time. Printing with very high starting temperature, this leads to distortions of the hot-laminate film. Generally, a platform that is kept too hot leads to distortions of the printed objects in the transition area.
Have fun experimenting with hot-laminated films...I give no guarantee at this point for success!
It's exactly this:
The laminator is a simple bonding agent for fixing a hot-laminate film as a removable printing underlay. The preparation of a hot-laminate film to be used as a well-adherent and low-cost object support for problematic PLA filaments (...or special filaments with a similar temperature range.). By creating a very first layer on the laminate film, the film and a carrier plate can be very well connected. Air pockets can be reduced in advance, or at best, they are totally eliminated. In addition, with this first printing process, by observing and adjusting the temperature and motion settings, a later big waste of material due to material warping can be avoided. If the recommendations are correctly implemented, printed surfaces achieve the same gloss level as if they had been printed directly on heated glass (...without adhesive additives.). Once optimally applied, it can be easily printed on the laminate film many times. It lasts for half an eternity until the foil becomes unusable...
I have made many other attempts to apply laminate film bubble free, but this method is currently the best for my concerns.
Introduction:
The laminator is a simple but reliable bonding agent for fixing a ordinary hot-laminate (PP / PE / film 0.08 - 0.12mm) on a build platform as a easy replaceable print underlay for poor adhesion PLA and (experimentally) other filaments. The main purpose of object named: the laminator ;is a good print preparation. In addition to the fixation of the laminate film, the formation of air pockets between the carrier plate and the film to be applied should be avoided as a precaution. For this, the printhead drives at best over the entire base area and creates a first layer, already with the desired material. In the template, almost 100% of the footprint of the Ultimaker 2 is covered, but of course you can make adjustments with the zoom function of the slicer of your choice. A parallel line structure is created, which must of course be removed before the actual printing process. Already during and after this first step you can determine if the material adhesion and the selected temperatures are optimal for the following printing process.
The advantages / disadvantages:
Exemplary example: PLA-HT (by Multec) adheres good to hot-laminate foil. This filament sticks very badly on most common construction surfaces. But it also has many advantages during processing. Because there are almost no lint by retractions and driving without material. Objects with large overhangs succeed better. With this material can be produced very detailed replicas that require very little post-processing. Special filaments or PLA grades with poor adhesion may better adhere to laminate films. No expensive BlueTape, hair spray, or other questionable bonding agent required. Hot-laminate film can be removed at room temperature from many surfaces absolutely residue-free, I have tested it on aluminum with PEI coating. A well-aligned print bed does not need to be re-aligned because the laminate films are very thin (0.08 - 0.12mm). Generally reduce the initial layer thickness by about 33%. So reduce 0.3mm to 0.2mm or just 100% to 66% material flow.
Important:
This method is NOT suitable for filaments printed at very high temperatures above 195...210 degrees in the first layer, or when material generally needs to be kept extremely warm throughout the entire printing time. Printing with very high starting temperature, this leads to distortions of the hot-laminate film. Generally, a platform that is kept too hot leads to distortions of the printed objects in the transition area.
Have fun experimenting with hot-laminated films...I give no guarantee at this point for success!
Similar models
thingiverse
free
Air Gun Holder (T-Track Mount) by Reckliss
...track mount) by reckliss
thingiverse
printed using pla filament
layer height: 0.175
hot end temperature: 240
bed temperature: 70
thingiverse
free
Swimbait by Brarups
... for better bed adhesion.
just remove useless material, when the print is finished.
use 2mm thick acrylic glass for the tail fin.
thingiverse
free
Fast Temperature Tower by Tacblades
...layer no. (from 1 and every 50) keep value and set extruder temp see image.
then just slice and print see tips below for slicing.
thingiverse
free
Split Test by NeatherBot
...q
this is now one of my standard prints that i do whenever i start using a new filament.
no infill
no support
2 perimeters
enjoy!
thingiverse
free
Temperature calibration cube by deltapenguin
... separation. i had a bad green pla filament on the picture that was useless and i printed a cube to convince the filament seller.
cg_trader
$5
Klee Genshin Impact | 3D
...zzle
-material was pla with a temperature of 205º and ventilation at 60%, the table at 60º
-layer height of 0.08 and tree support
thingiverse
free
Afinia H480 Filament feeder reinforcement by imaicom
...s are easy to break. there is no choice but to strengthen it.
please print with abs filament. it must be fixed with abs adhesive.
thingiverse
free
Maker Vikings Assistive Tech (Make:able Challenge) by LuisArizmendi02
...pla
spring: cut from spring of a pen
slider with puller: use pla
insert: use pla; edit to attach tool end (ex: fork, spoon, ect.)
thingiverse
free
WADE'S EXTRUDER MEXIFLEX prusa i3 by IMPRESSIVE3D
...mm/s
extruder temperature: 210-230 ∞c
hot bed temperature: 50-80 ∞c you can also improve the adhesion with spray hair and 3m tape
cults
free
Filament Temperature Tag
...nd debossed version.
when printing embossed version, stop at 1mm height and change filament color.
abs: 210 ~ 270
pla: 180 ~ 230
Mnis
thingiverse
free
Mni Blaster by LethalTeaspoon
...mni blaster by lethalteaspoon
thingiverse
a mini blaster sci-fi type gun, its very small about 90mm long. enjoy.
thingiverse
free
Galaxy S5 Stand by mnis
...galaxy s5 stand by mnis
thingiverse
an easy-to-print smartphone stand for the samsung galaxy s5.
thingiverse
free
Universal Hooks by mnis
...ption:
scale the s-hooks to a desired size or use the sizes available.
use single hooks. or use double hooks (... male / female).
thingiverse
free
Ring for GU10 to E27 Adapter by mnis
...ring for gu10 to e27 adapter by mnis
thingiverse
note:
please read the description in the attached picture.
thingiverse
free
UDB (Universal Device Base) by mnis
...universal device base) by mnis
thingiverse
description:
universally usable device feet (...to alleviate vibration and slippage).
thingiverse
free
LiteOn eSAU208 ODD Enclosure by mnis
...liteon esau208 odd enclosure by mnis
thingiverse
a completely new housing for the liteon optical disc drive esau208.
thingiverse
free
LED-Remote-Holder by mnis
...e
three simple variants of remote control holders.
and many types of plastic cards (credit cards, etc.) fit in these holders :-)
thingiverse
free
Soken RK1 01 Rocker by mnis
...en rk1 01 rocker by mnis
thingiverse
this object replaces a defective on / off rocker of the switch with the name: soken rk1 01.
thingiverse
free
Door Lock by mnis
...n windows or maintenance flaps.
door thickness max: 3mm
thickness of the frame max: 6mm
note: all parts have not been tested yet.
thingiverse
free
Gunpla aftermarket mni gatling gun by Mokanaman
...gunpla aftermarket mni gatling gun by mokanaman
thingiverse
aftermarket part to customize your gundam models.
Laminator
3d_export
$20
Design of automatic laminator
...design of automatic laminator
3dexport
design of automatic laminator
turbosquid
$19
Laminated Shelf
...odel laminated shelf for download as blend, 3ds, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1389343)
turbosquid
$55
Laminating machine
...chine for download as 3ds, max, ige, obj, fbx, stl, and sldas on turbosquid: 3d models for games, architecture, videos. (1293323)
3d_ocean
$2
Laminate Tiles Texture
...e contains diffuse and bump maps (2048×2048) in jpg format and a rendered image. reflections and highlight are perfectly trace...
turbosquid
$7
Cantilever laminate mechanism
...inate mechanism for download as 3ds, ige, obj, stl, and sldas on turbosquid: 3d models for games, architecture, videos. (1227218)
turbosquid
$6
The pressure laminate mechanism
...nate mechanism for download as 3ds, ige, obj, stl, and sldas on turbosquid: 3d models for games, architecture, videos. (1224220)
turbosquid
$55
ACF laminating machine
...chine for download as 3ds, max, ige, obj, fbx, stl, and sldas on turbosquid: 3d models for games, architecture, videos. (1289996)
3d_export
$5
electronic products automatic laminating machine
...electronic products automatic laminating machine
3dexport
3d model of electronic products automatic laminating machine
evermotion
$8
office plastic laminator 59 AM87
...laminator with all textures, shaders and materials. it is ready to use, just put it into your scene.. evermotion 3d models shop.
turbosquid
$6
LAMINATED WOOD FINISH DOORS
...ted wood finish doors for download as ma, max, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1274300)