Thingiverse
TH8RS Sequential Shifter mod
by Thingiverse
Last crawled date: 4 years, 4 months ago
A mod I made that brings the TH8RS shifter sequantial mode into completely new level.
More details in the video: https://youtu.be/ftoNNL1reJ8
NOTE: after using the mod quite intensively I found a major flaw in the design - the friction between shifter shaft and the spring ball screws is resulting in occasional locking of the shifter and scratches on the shaft. You could use some kind of grease to prevent that but it would make the whole thing messy, so I inverted the design: springs are on the top and ball screws right over the base plate. At this height the shaft has a teflon insert therefore the friction is minimised and everything works smoothly.
If you like it consider a small tip: https://paypal.me/PeterMakesThings?locale.x=en_GB
Parts list:
3D models
4x M3 25mm screws
4x M3 nuts
2x M4 nuts
2x M4 screws (around 15mm long)
4x M610mm Spring Ball Plunger screws (https://tinyurl.com/w6wjjx2)
2x Springs for 3d printer bed: 20mm 7.5mm * 1.2mm (https://tinyurl.com/s4sbl6c)
Original concept by dukethirteen: https://www.thingiverse.com/thing:3406574
More details in the video: https://youtu.be/ftoNNL1reJ8
NOTE: after using the mod quite intensively I found a major flaw in the design - the friction between shifter shaft and the spring ball screws is resulting in occasional locking of the shifter and scratches on the shaft. You could use some kind of grease to prevent that but it would make the whole thing messy, so I inverted the design: springs are on the top and ball screws right over the base plate. At this height the shaft has a teflon insert therefore the friction is minimised and everything works smoothly.
If you like it consider a small tip: https://paypal.me/PeterMakesThings?locale.x=en_GB
Parts list:
3D models
4x M3 25mm screws
4x M3 nuts
2x M4 nuts
2x M4 screws (around 15mm long)
4x M610mm Spring Ball Plunger screws (https://tinyurl.com/w6wjjx2)
2x Springs for 3d printer bed: 20mm 7.5mm * 1.2mm (https://tinyurl.com/s4sbl6c)
Original concept by dukethirteen: https://www.thingiverse.com/thing:3406574
Similar models
thingiverse
free
Sim Racing Paddle Shifter
... m3 nut (for securing paddle to shaft)https://www.mcmaster.com/90592a085
4x m3 screws for mounting shifter to button box or plate
thingiverse
free
Triple magnet Paddle Shifter for SimRacing
...2mm/10mm/6mm
2x m3 35mm screws
4x m3 12mm screws
2x m3 6mm screws
6x m3 washers
2x m3 nuts
if you like it please buy me a beer :)
thingiverse
free
Sequential shifter
...50 mm screw
4x m3 nut
8x m3 washer
2x foam rubber 28x25x20 mm
2x m6 15 mm wood screw
2x micro switch 16a 30x15x10 mm
wire 3 m
thingiverse
free
Spring Paddle Shifters for Sim Racing
...or 2 x m3 45mm
edit 2019.11.07 -> added 'paddle v2.stl' which allows for more space between the rim and paddle shifter
thingiverse
free
Prusa i3 (FolgerTech) 2004 LCD screen holder by zxqueb
... and the back of the top aluminum bar. for mounting i used:
4x m3 14mm screws
4x m3 lock nuts
2x m4 12mm screws
2x m4 t-nuts
thingiverse
free
TH8A / TH8RS H-pattern improved feel mod
...h-pattern mod, it has a bunch of improvements over similar solutions available. overview: https://youtu.be/zjpheq71d44 if you like my designs...
thingiverse
free
Motor housing for flying sea turtle
... jack ( https://tinyurl.com/wzgbau9 )
5v dc power adapter ( https://tinyurl.com/wwpk9qe )
2x m4x12 counter sunk screws
2x m4 nuts
thingiverse
free
(BTT) TFT35 v2 Display Mount by lukeone
...ws for the mount
4x m3x10 screws + m3 nuts for the display
and of course a bigtreetech tft35 v2 https://amzn.to/3aweaqa
have fun!
thingiverse
free
Contra-rotating Wind Turbine by OspreyGozo
...8 lock nuts per turbine
vertical shaft barcket:
2x m8 nuts
2x m8 lock nuts
2x m8 washers
4x m3x20 screws
4x m3 nuts
4x m3 washers
thingiverse
free
Ender 3 Ultimate Spool Holder
...t combos (for attaching to frame)
spoolholder part has guide hole that can be drilled out if m3 bolt does not have leading point.
Th8Rs
thingiverse
free
Thrustmaster TH8A, TH8RS Shiftknob by Antongotberg
...thrustmaster th8a, th8rs shiftknob by antongotberg
thingiverse
shiftknob for thrustmaster th8a/th8rs
thingiverse
free
TH8A/TH8RS handbrake plate by ikbendusan
...lol
what you see is what you get.
! warning !
don't over-tighten the bolts, the layers may separate where the counterbore is.
thingiverse
free
Thrustmaster TH8A/TH8RS Short throw(6 gate remix) by teknogeek1300
... version of wotever short throw mod. requires longer screws(m3x35mm)
i printed it upside down, with support around the outer lip.
thingiverse
free
TH8A / TH8RS mod (remix) by AtoMic09
...ions to accept these teflon pads.https://www.amazon.ca/gp/product/b01lz44p6m/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=utf8&psc=1
thingiverse
free
Thrustmaster TH8A/TH8RS Short throw(Remix) by teknogeek1300
...tions, then reinstalled this gate.
requires m3x35mm bolts/screws, i recommend washers to spread the stress(as shown in pictures).
thingiverse
free
TH8A / TH8RS H-pattern improved feel mod
...m/w6wjjx2
teflon glide pads (20x20x6 mm, one needs to be cut to 15x14mm size!): https://tinyurl.com/wuhwbso
zip tie
bit of grease
thingiverse
free
![TH8A/TH8RS [short/long] shifter plate (multiple layouts) by ikbendusan](/t/8585595.jpg)
TH8A/TH8RS [short/long] shifter plate (multiple layouts) by ikbendusan
...parate during use, which rendered the plate useless. if you did break yours, let me know and i'll upload a bushing to fix it.
thingiverse
free
Thrustmaster TH8A/TH8RS Short throw shifter mod by Wotever
...t a clean "lip"
you can use heat shrink tube to preserve your axis from wear (i only had electrical tape under hand :d)
thingiverse
free
Thrustmaster TH8A Shiftknob by MK3424
...by mk3424 thingiverse custom shiftknob for your th8a or th8rs shifter. this shiftknob is closer to the shifter base...
Sequential
thingiverse
free
Sequential Gearbox by NateTG
...tg
thingiverse
constant mesh sequential gearbox using emmet's gear bearings. i need to work out how to make it printable...
thingiverse
free
Sequential shifter
...50 mm screw
4x m3 nut
8x m3 washer
2x foam rubber 28x25x20 mm
2x m6 15 mm wood screw
2x micro switch 16a 30x15x10 mm
wire 3 m
thingiverse
free
Sequential expanding mechanism box by Frolgo
...o
thingiverse
this is a nice box with a twist. to open the upper lid has to be turned. then the three leavers expand sequential.
thingiverse
free
TH8 SEQUENTIAL KNOB by Fox_85
...th8 sequential knob by fox_85
thingiverse
this is my thrustmaster th8 secuantial knob
thingiverse
free
Sequential Shifter bracket for Logitech G27 by TacosForJesus
...
slips on the mounting knobs and secured with elastics to pull the lever out of gear in order to use it as a sequential shifter.
thingiverse
free
sequential shifter MOD g27 by elgh33
...t + right model
makes the gated to sequential shifter inspired by madlap but made with 100% own measurements from the g27 shifter
thingiverse
free
Weighted Sequential Shift Knob by E_Elisio
... fanatec clubsport ssq shifter. has a slot to fit a 3/4" x 2" bolt and x3 hex nuts of the same size to act as a weight.
thingiverse
free
Sim Racing Sequential Shifter upgrade by clos2727
...stant stress applied all parts sjould be printed at 100% infill.
except for switch cover.
filament used for this project is pla.
thingiverse
free
Sequential Shifter DIY SIM RIG by DrBrauch
...n pic) to make shaft stand and make sequential feel great.
need 5 long bolt
for shaft prefer change to stainless steel shaft 10mm
thingiverse
free
SSH Shifter Sequential clip-on Plate
...st clip on an existing plate by holding on original plate screws. it's two parts so you do not have to remove the shift knob.
Shifter
thingiverse
free
shifter plates for a shifter im making by stockcar
...shifter plates for a shifter im making by stockcar
thingiverse
making a shifter for online racing.
thingiverse
free
Skull Shifter by ColeDowns
...skull shifter by coledowns
thingiverse
just a shifter
thingiverse
free
Bicycle shifter by Rumble89
...bicycle shifter by rumble89
thingiverse
shifter for a hub circuit.
thingiverse
free
Playseat Shifter Holder
...playseat shifter holder
thingiverse
playseat shifter holder
thingiverse
free
H-Shifter / Vites
...h-shifter / vites
thingiverse
h-shifter model
thingiverse
free
Shifter for audi A3
...shifter for audi a3
thingiverse
shifter for audi a3
thingiverse
free
SHIFTER SRAM SUPPORT
...shifter sram support
thingiverse
shifter sram support
thingiverse
free
pommeau shifter logitech
...pommeau shifter logitech
thingiverse
pommeau shifter logitech
thingiverse
free
Shifter by boyleengineering
...shifter by boyleengineering
thingiverse
thingiverse
free
Round Knob Shifter
...round knob shifter
thingiverse
knob shifter for car models
Mod
thingiverse
free
HB-MOD-ETH Gehäuse RPI-RF-MOD by Dquantz
...hb-mod-eth gehäuse rpi-rf-mod by dquantz
thingiverse
case for hb-mod-eth with rpi-rf-mod
thingiverse
free
Dumbo ears mod
...dumbo ears mod
thingiverse
ears mod
thingiverse
free
YoYo Mod by 19pdansor
...yoyo mod by 19pdansor
thingiverse
a yoyo mod
thingiverse
free
Freecoaster mod by imbrid
...freecoaster mod by imbrid
thingiverse
freecoaster mod
thingiverse
free
mods by wtrduflo
...mods by wtrduflo
thingiverse
thingiverse
free
SapphirePro Cable Mod
...sapphirepro cable mod
thingiverse
a cable mod for the sapphire pro.
thingiverse
free
NLPWM Mod Box
...nlpwm mod box
thingiverse
my first mod mox
thingiverse
free
Silencer Mod by jakkal
...silencer mod by jakkal
thingiverse
silencer mod.
great sucess
thingiverse
free
eye mod
...eye mod
thingiverse
eye eye
thingiverse
free
MPCNC Belt Mod
...mpcnc belt mod
thingiverse
belt mod for mpcnc. alternative to zip tie.