Thingiverse
Test lung by emermedpirineus
by Thingiverse
Last crawled date: 3 years, 4 months ago
Disclaimer: build intended only for educational or simulation purposes.
Commercial test lungs, like the dräger one, can be really expensive so we designed a low cost, low complexity one using a latex balloon from an anesthesia or ventilator circuit. Our model is thought to be connected to an quick garden hose connector** but since the anesthesia balloon has standard connection measurements, it can be also attached directly to a ventilator tubing. This model is capable of firing vent inspiration trigger just taking apart both aluminium plates. Also sliding a overwidth wood strip clamp over the plates allows to change the model’s distensibility.
Bill of materials:
-. Anesthesia circuit balloon, a 3 liter one in our case.
-. Aluminium plate, shaped to cover nearly all the balloon length and width, in our case it's mostly a kind of rectangle 13x35cm with the edges on one side cut. We used 0,8mm thick plate but other materials or sizes might be useful as well.
-. 3D printed spacer and connector.
-. Wood strips. We used Kapla sized ones, but any size wider than the end of the plate will work.
-. Nuts and bolts, again any fitting size can be used.
-. Silicone tubing, 10 cm length x 10 mm internal diameter.
-. Quick hose connector.
-. Worm clamp.
Building
-. Cut (and polish edges) the aluminium plates adjusted to the balloon size.
-. Mark and drill the holes in the plates adjusted to 3D printed spacer holes.
-. Place balloon between spacer parts and plates and fix it with the nuts you have.
-. Drill holes in two same-sized wood strips. Put nuts to attach both strips and clamp the end of the plates AND the balloon end.
-. Attach one end of silicone tubing to the quick hose connector and the other to the 3D printed connector, fix it with the worm clamp.
-. Insert the connector to the balloon. If there are any leaks you can add sealing tape at the connector end to increase its diameter and fix the issue.
** See https://www.sciencedirect.com/science/article/abs/pii/S1695403310002808 to understand why
Commercial test lungs, like the dräger one, can be really expensive so we designed a low cost, low complexity one using a latex balloon from an anesthesia or ventilator circuit. Our model is thought to be connected to an quick garden hose connector** but since the anesthesia balloon has standard connection measurements, it can be also attached directly to a ventilator tubing. This model is capable of firing vent inspiration trigger just taking apart both aluminium plates. Also sliding a overwidth wood strip clamp over the plates allows to change the model’s distensibility.
Bill of materials:
-. Anesthesia circuit balloon, a 3 liter one in our case.
-. Aluminium plate, shaped to cover nearly all the balloon length and width, in our case it's mostly a kind of rectangle 13x35cm with the edges on one side cut. We used 0,8mm thick plate but other materials or sizes might be useful as well.
-. 3D printed spacer and connector.
-. Wood strips. We used Kapla sized ones, but any size wider than the end of the plate will work.
-. Nuts and bolts, again any fitting size can be used.
-. Silicone tubing, 10 cm length x 10 mm internal diameter.
-. Quick hose connector.
-. Worm clamp.
Building
-. Cut (and polish edges) the aluminium plates adjusted to the balloon size.
-. Mark and drill the holes in the plates adjusted to 3D printed spacer holes.
-. Place balloon between spacer parts and plates and fix it with the nuts you have.
-. Drill holes in two same-sized wood strips. Put nuts to attach both strips and clamp the end of the plates AND the balloon end.
-. Attach one end of silicone tubing to the quick hose connector and the other to the 3D printed connector, fix it with the worm clamp.
-. Insert the connector to the balloon. If there are any leaks you can add sealing tape at the connector end to increase its diameter and fix the issue.
** See https://www.sciencedirect.com/science/article/abs/pii/S1695403310002808 to understand why
Similar models
thingiverse
free
CNC Dust Shoe (Adjustable Height) by withewolf
...tion is glued into the acrylic glass.
there are 2 screws at the top end of the aluminium tubes to prevent them from slipping out.
thingiverse
free
JJ lung flush connectors by GregPye
...side.
o-rings needed are 34x2 for the lower end (same for the original). hose end ones are the standard ones for such connectors
thingiverse
free
Radiant Tube for 2 Inch water hose by NGee3D
...r. maybe the gap is a little bit to small in the windings. but i had succes with some sandpaper and screwing it while it was wet.
grabcad
free
Tubing Beader 1 Inch
...rabcad
this is for putting a bead in the end of tubing, normally used to retain a rubber hose attached and clamped over the bead
thingiverse
free
Ventilator hose splitter by vince31
... down, no supports required.
accepts 22mm outside diameter silicone tubing as an adapter for the 22mm ventilator hose to mate to.
thingiverse
free
Garden Hose Male to 1/2" Barb for Hose Repair by cudatox
...a 16mm nut (24mm between the flats).
you will need a gear clamp to attach it and it may require quite a bit of clamping pressure.
thingiverse
free
KF-16 Hose Clamp to wood end grain by TyphonDeLeon
...kf-16 hose clamp to wood end grain by typhondeleon
thingiverse
hose clamps to hold kf-16 bellows tube to 2x3 lumber endgrain
grabcad
free
2.5" Hose Clamp
...2.5" hose clamp
grabcad
2.5" worm-drive hole clamp
thingiverse
free
Ender IDEX Screen Spacer, Ender 3 / Pro by Darkmyer
...hat attache the screen to the printer to attach the spacer to the extrusion then use two more to attach the screen to the scacer.
thingiverse
free
8mm Hose Y Connector by Depdog747
...8mm hose y connector by depdog747
thingiverse
quick remix of the hose connector for some 8mm tube.
Lung
turbosquid
$10
Lung
...ng
turbosquid
royalty free 3d model lung for download as max on turbosquid: 3d models for games, architecture, videos. (1569917)
turbosquid
$15
Lung
...oyalty free 3d model lung for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1403728)
turbosquid
$40
lung
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
lungs
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
Lung
...e 3d model lung for download as jpg, bmp, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1403595)
turbosquid
$2
Lungs
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$19
Tract lung trachea Human Lung Right and Bronchi
... trachea human lung right and bronchi
3dexport
1.tract lung trachea human lung right and bronchi 2.files include 3dmax fbx obj
3d_ocean
$15
Human lungs
...on imagination laboratory lungs medical organ render science skeleton texture three-dimensional x-ray
3d human lungs and material
3ddd
free
Подушки Naked Lunge
...подушки naked lunge
3ddd
подушка
подушки для декора naked lunge
turbosquid
$79
Lungs and Trachea
...e 3d model lungs and trachea for download as ma, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1579296)
Test
turbosquid
$99
test
...st
turbosquid
royalty free 3d model test for download as max on turbosquid: 3d models for games, architecture, videos. (1251637)
turbosquid
$63
TEST
...st
turbosquid
royalty free 3d model test for download as max on turbosquid: 3d models for games, architecture, videos. (1446233)
turbosquid
$1
test
...st
turbosquid
royalty free 3d model test for download as fbx on turbosquid: 3d models for games, architecture, videos. (1360941)
3d_export
free
johnny test
...johnny test
3dexport
johnny test 3d
turbosquid
$15
Test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
gripper test
...gripper test
3dexport
robot gripper test model