Thingiverse
Team Associated RC10/RC10T/RC10T2 Front Spindle by rcnand
by Thingiverse
Last crawled date: 3 years, 5 months ago
Front spindle/carrier for a variety of different vintage Team Associated vehicles with inline axles (RC10, RC10T, RC10T2 - 6221).
These are starting to become increasingly expensive/harder to find even though they used to be widely available. The stock part is composed of nylon, so this part would likely be a "get by" unless you can print in a material of sufficient impact resistance.
Ream the kingpin/hinge pin hole with a 1/8" drill bit. The front axle hole is slightly smaller than a 1/4" bit; a 15/64" bit is close but not perfect. Use a file if you need to get a better fit for the axle. Ideally, you want to keep clearance to a minimum. You may also need to lightly file the flats on which the spindle pivots to allow for smooth motion.
NOTE: I have not yet printed this yet; but an earlier revision that I have modified was very close, so I would expect that this is very close to what is needed. If your printing tolerances are a little better, you may need to tweak the hole sizes slightly.
These are starting to become increasingly expensive/harder to find even though they used to be widely available. The stock part is composed of nylon, so this part would likely be a "get by" unless you can print in a material of sufficient impact resistance.
Ream the kingpin/hinge pin hole with a 1/8" drill bit. The front axle hole is slightly smaller than a 1/4" bit; a 15/64" bit is close but not perfect. Use a file if you need to get a better fit for the axle. Ideally, you want to keep clearance to a minimum. You may also need to lightly file the flats on which the spindle pivots to allow for smooth motion.
NOTE: I have not yet printed this yet; but an earlier revision that I have modified was very close, so I would expect that this is very close to what is needed. If your printing tolerances are a little better, you may need to tweak the hole sizes slightly.
Similar models
thingiverse
free
Team Associated RC10T2 Front Body Post Mount by rcnand
...body mount bracket for the rc10t2.
you may need to ream out the screw holes slightly, but 4-40 screws should thread in just fine.
thingiverse
free
Team Associated RC10T/RC10T2 12mm Hex Adapter by rcnand
...ssociated/team losi front bearing supported rims, the rear will be ~7 mm total (3.5 mm per side) wider when you use this adapter.
thingiverse
free
Team Associated RC10T2 Front Caster Blocks (30 Degree) by rcnand
...bit and tap the ball stud mount with a 4-40 tap.
if time allows, i may upload a 25 degree version (not that difficult to modify).
thingiverse
free
Team Associated RC10T2 Front Caster Blocks (25 Degree) by rcnand
...2. this is the 25 degree version.
ream the hinge pin hole with a 1/8" drill bit and tap the ball stud mount with a 4-40 tap.
thingiverse
free
Team Associated RC10T2 Front Mini Bumper by rcnand
...screw countersinks may need a light filing after printing. similary, you could probably modify this bumper to use more...
thingiverse
free
Team Associated RC10T2 Front Bulkhead by rcnand
... with the chassis. all directional improvements - but i will change this from a work in progress to complete once i have printed.
thingiverse
free
Team Associated RC10T2 Front Bulkhead by rcnand
...he areas near the hinge pin mounts may need to be filed slightly to clear the chassis (depending on tolerances for your printer).
thingiverse
free
Team Associated RC10T2 Front Body Post Mount by rcnand
...unting bracket for the rc10t2.
this is not a very complex component, but print orientation will be critical to maintain strength.
thingiverse
free
Low Profile Front Bumper for RC10 Gold Pan by WTF_Racing
...;s.
i have not printed one of these yet, so if you do and have any comments please share them so i might make this design better.
thingiverse
free
Schumacher Cougar 2000/Fireblade Front Bulkhead by rcnand
...very much as you want a nice snug fit. similary, you may need to file the hinge area slightly....
Rc10T
thingiverse
free
RC10T Shock Mount Bushing by Driftpony
...rc10t shock mount bushing by driftpony
thingiverse
shock mount bushing based on rc10t bushing, also tested and fits rc10t4.
thingiverse
free
Team Associated RC10T/RC10T2 12mm Hex Adapter by rcnand
...ssociated/team losi front bearing supported rims, the rear will be ~7 mm total (3.5 mm per side) wider when you use this adapter.
thingiverse
free
RC10 T rear shock tower by Nemesisllama
...shock tower by nemesisllama thingiverse rear shock tower for rc10t ...
thingiverse
free
Team Associated RC10T2 Front Mini Bumper by rcnand
...ight filing after printing. similarly, you could probably modify this bumper to use more traditional non-100 degree countersinks.
thingiverse
free
Axial SCX10 radio box and ESC mount by ieatdrt
...an scx10, rc10b3, sct410.3, tamiya hilux, losi 5ive-t, savage, rc10t (alum. pan) to be able to make parts for,...
thingiverse
free
Team Associated/Team Losi HPI 5X11 Bearing Adapter by rcnand
...traxxas nitro rustler ream rim for the rc10t/rc10t2. for losi/rc10t+, you will need ~8.5 mm thick adapter. this is...
Rc10T2
thingiverse
free
Team Associated RC10T2 Front Body Post Mount by rcnand
...unting bracket for the rc10t2.
this is not a very complex component, but print orientation will be critical to maintain strength.
thingiverse
free
Team Associated RC10T2 Front Body Post Mount by rcnand
...body mount bracket for the rc10t2.
you may need to ream out the screw holes slightly, but 4-40 screws should thread in just fine.
thingiverse
free
Team Associated RC10T2 Servo Mount/Spacer by rcnand
... an exact match for originals (2.4 vs 2.5 mm). these could easily be modified to match.
tap the mounting holes with a 4-40 tap.
thingiverse
free
Team Associated RC10T2 Rear Lower Shock Mount by rcnand
... larger to allow the screws to pass through more cleanly (if desired). the shock mounting holes should be tapped with a 4-40 tap.
thingiverse
free
Team Associated RC10T2 Front Caster Blocks (25 Degree) by rcnand
...2. this is the 25 degree version.
ream the hinge pin hole with a 1/8" drill bit and tap the ball stud mount with a 4-40 tap.
thingiverse
free
Team Associated RC10T2 Front Caster Blocks (30 Degree) by rcnand
...bit and tap the ball stud mount with a 4-40 tap.
if time allows, i may upload a 25 degree version (not that difficult to modify).
thingiverse
free
Team Associated RC10T2 Front Mini Bumper by rcnand
...ight filing after printing. similarly, you could probably modify this bumper to use more traditional non-100 degree countersinks.
thingiverse
free
Team Associated RC10T/RC10T2 12mm Hex Adapter by rcnand
...ssociated/team losi front bearing supported rims, the rear will be ~7 mm total (3.5 mm per side) wider when you use this adapter.
thingiverse
free
Team Associated RC10T2 Front Bulkhead by rcnand
... with the chassis. all directional improvements - but i will change this from a work in progress to complete once i have printed.
thingiverse
free
Team Associated RC10T2 Front Bulkhead by rcnand
...he areas near the hinge pin mounts may need to be filed slightly to clear the chassis (depending on tolerances for your printer).
Rcnand
thingiverse
free
Schumacher Cougar/Storm 2000 Front Bumper by rcnand
.../storm 2000 front bumper by rcnand
thingiverse
front bumper for the schumacher cougar 2000 and storm 2000 r/c vehicles (u1456v).
thingiverse
free
Kyosho Raider Steering Servo Mount by rcnand
...here is not a lot to say about this part as it is pretty simple. tap the mounting holes with a m3 tap, and use m3 machine screws.
thingiverse
free
Schumacher Servo Mount by rcnand
...not yet printed to confirm dimensions of this latest iteration. it should be pretty close, but i will update when i have printed.
thingiverse
free
Team Associated RC10T2 Front Body Post Mount by rcnand
...unting bracket for the rc10t2.
this is not a very complex component, but print orientation will be critical to maintain strength.
thingiverse
free
Team Associated RC10T2 Front Body Post Mount by rcnand
...body mount bracket for the rc10t2.
you may need to ream out the screw holes slightly, but 4-40 screws should thread in just fine.
thingiverse
free
Schumacher Cougar 2000 Front Shock Tower Spacer by rcnand
... connection for the schumacher cougar 2000 (u1449o).
pretty simple part - you may need to ream the through holes with a 3 mm bit.
thingiverse
free
Tamiya DF01 Wing Mount by rcnand
...or those who may have misplaced the original).
tap the mounting holes with a m3 tap and use m3 hardware to retain the wing/mount.
thingiverse
free
Team Associated RC10T2 Servo Mount/Spacer by rcnand
... an exact match for originals (2.4 vs 2.5 mm). these could easily be modified to match.
tap the mounting holes with a 4-40 tap.
thingiverse
free
Team Associated RC10T2 Rear Lower Shock Mount by rcnand
... larger to allow the screws to pass through more cleanly (if desired). the shock mounting holes should be tapped with a 4-40 tap.
thingiverse
free
Team Losi Rear Hinge Clip - JRX-Series by rcnand
...arm hub clip) for a variety of older team losi jrx-series based vehicles (jrx-pro, jrx-pro se, junior t, junior 2, lxt - a-2021).
Rc10
thingiverse
free
RC10 Rear Bulkhead by Pete1987
...ingiverse
rc10 rear bulkhead modeled from an original. there are two versions. one without logo and one with a little rc10 logo.
thingiverse
free
RC10 Shock Tower by Pete1987
...rc10 shock tower by pete1987
thingiverse
rc10 shock tower modeled from an original edinger style.
thingiverse
free
rc10 wheel by muricaforthewinusa
...thewinusa
thingiverse
prefab rear wheel for the team associated rc10 b 4.2 rtr buggy. offroad/sand/snow and other tires to come
thingiverse
free
RC10 Classic StealthTransmission Brace by mojobromley
...rc10 classic stealthtransmission brace by mojobromley
thingiverse
rc10 classic stealthtransmission brace
thingiverse
free
Classic RC10 Battery strap by mojobromley
...classic rc10 battery strap by mojobromley
thingiverse
classic rc10 battery strap
thingiverse
free
RC10 inspired spinner by BasslinedRC
...front wheels of the vintage rc10. uses a 608 bearing for the main bearing, and 608 inner races for the weights, or whatever fits.
thingiverse
free
RC10 Andy's Front A-Arm by Pete1987
...rc10 andy's front a-arm by pete1987
thingiverse
rc10 andy's front a-arm modeled from an original.
thingiverse
free
RC10 Rear A-Arm Classic by Pete1987
...rc10 rear a-arm classic by pete1987
thingiverse
rc10 rear a-arm. modeled from using a classic (re-release) a-arm as reference.
thingiverse
free
RC10 Rear Knuckle by Pete1987
...ociated rc10 rear knuckle modeled from original part.
if you downloaded before 2/25/18 please re-download rear_knuckle_fixed.stl
thingiverse
free
RC10 Front Shock Tower by Pete1987
...ont shock tower by pete1987
thingiverse
rc10 front shock tower is 2.3mm thick. i also added a couple thicker part files as well.
Spindle
3d_export
$5
simple spindle
...simple spindle
3dexport
simple spindle
design_connected
$7
Spindle shade
...spindle shade
designconnected
rothschild&bickers spindle shade computer generated 3d model.
design_connected
$9
Spindle Table
...spindle table
designconnected
ligne roset spindle table computer generated 3d model. designed by ascalon, brad.
design_connected
free
Spindle Clock
...spindle clock
designconnected
vitra spindle clock free models computer generated 3d model. designed by george nelson.
turbosquid
$10
Spindle Table
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$9
DVD Spindle
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$9
Spindle-chair
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$15
Spike Spindle 3D Model
...s procession spindled spindling spiking spearing spear document bill hole paperwork
spike spindle 3d model firdz3d 90192 3dexport
turbosquid
$15
Nelson Spindle Clock
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
Vitra Spindle Clock
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Associated
turbosquid
$15
Craft associates sofa
...e 3d model craft associates sofa 3d model for download as max on turbosquid: 3d models for games, architecture, videos. (1545764)
3ddd
$1
Associated Chair
...associated chair
3ddd
обеденный
chair and table, ready for merge and render, real-world size (cm), photorealistic v-ray shaders
turbosquid
$20
Association of Southeast Asian Nations
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
cg_studio
$20
Association of Southeast Asian Nations3d model
...cgstudio
.mb - association of southeast asian nations 3d model, royalty free license available, instant download after purchase.
3d_export
$15
craft associates sofa
...r>-the 3d model is ready to use.<br>-all maps and materials are included.<br>-real world size (system units - cm).
3d_export
$20
Association of Southeast Asian Nations 3D Model
...tandard association of southeast asian nations asan asean
association of southeast asian nations 3d model rmodeler 37966 3dexport
3d_export
$9
Association of Southeast Asian Nations 3D Model
...tandard association of southeast asian nations asan asean
association of southeast asian nations 3d model rmodeler 38016 3dexport
3d_export
$23
korea football association
...mat upon request thank you for viewing & buying our products your satisfaction is a pride for us we really appreciate you ...
3d_export
$12
japan football association
...mat upon request thank you for viewing & buying our products your satisfaction is a pride for us we really appreciate you ...
3ddd
$1
VIVIA S19
...vivia s19
3ddd
massari&associates , toso
fbx\obj\max2011
Team
design_connected
$13
Team
...team
designconnected
arper team computer generated 3d model. designed by lievore, alberto.
3ddd
$1
Team 7
...team 7
3ddd
team 7
моделилось с кталога team 7
3ddd
free
team 7
...team 7
3ddd
team 7
стол фабрики team 7.
типы размеров /900,1000/x/1750,2000,2250/x/750/
раздвигается +600 или +1200
3d_export
$99
basketball team
...basketball team
3dexport
basketball team 3d model. rigged. include obj, fbx files.
design_connected
$18
Team - trestle
...team - trestle
designconnected
arper team - trestle computer generated 3d model. designed by lievore, alberto.
3ddd
$1
TEAM 7 Atelier
...team 7 atelier
3ddd
team 7 , стол
производитель team 7
модель atelier
3ddd
$1
Банкетка Flex Team
... , flex team
http://www.abitant.com/products/banketka-flex-team-2014-kilt-pouf
3d_export
$65
mountaineering team
...mountaineering team
3dexport
simple rendering of the scene file
3d_export
$65
Camel team
...camel team
3dexport
simple rendering of the scene file
3ddd
$1
Стол Joha-team - BaumArt
... joha , team
стол от joha-team, под названием baumart
Front
archibase_planet
free
Front
...front
archibase planet
facade front bluff
front 3d01a - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
front fork
...front fork
3dexport
front fork
3d_export
$5
Front Desk
...front desk
3dexport
modern and minimal reception front desk
3d_ocean
$4
Medical Front
...medical front
3docean
horror low medical
medical front
3d_ocean
$5
Front Desk
...front desk
3docean
desk front office reception
office reception counter or front desk. cad file and obj file included.
3ddd
free
Axor WaterDream by Front
...r , waterdream , front
axor waterdream by front
3d_export
$5
front nut eye
...front nut eye
3dexport
front nut eye
3d_export
$5
front screw eye
...front screw eye
3dexport
front screw eye
3d_export
$5
front clamping device
...front clamping device
3dexport
front clamping device
archive3d
free
Front 3D Model
...rchive3d
facade front bluff
front 3d01a - 3d model (*.gsm+*.3ds) for interior 3d visualization.